Getting Started (Stereo Receiver: Sx-P01, Sx-P01Dab); To Turn The Power On; Setting The Clock; General Functions - Pioneer N-P01-S Operating Instructions Manual

11
11

Getting started (Stereo receiver: SX-P01, SX-P01DAB)

To turn the power on

Press the I SYSTEM ON button on the remote control to turn
on both of the stereo receiver and network audio player.
To turn on the stereo receiver only:
Press the  RECEIVER button on the remote control or the /
I STANDBY/ON button on the stereo receiver.

Setting the clock

SYSTEM ON RECEIVER CD NETWORK
TIMER
SYSTEM OFF
CONTROL
RCV CD NET TOP
MENU
CD/USB CD USB DIRECT
TREBLE
TUNER BAND FAVORITES
NETWORK M.SERVER NET SERVICE
SETUP
BASS
DIG IN 1/2 iPod/USB BT AUDIO
AUTO TUNE
TIMER SLEEP CLOCK DIMMER
In this example, the clock is set to the 24-hour (0:00) display.
1 Turn on the stereo receiver.
Refer to To turn the power on above for details.
2
Press the CONTROL RCV button on the remote control.
3
Press the CLOCK button on the remote control.
The current day and time are displayed.
The default setting (Sun 0:00) is displayed when the first time
you set the clock.
4
Press ENTER button.
Use / to set the day, then press ENTER.
5
44
Use / to select 24-hour or 12-hour display, then
6
press ENTER.
Use / to set the hour, then press ENTER.
7
Use / to set the minute, then press ENTER to
8
confirm.
Note
• Press the CLOCK or RETURN button to exit the setting
SLEEP CLOCK DIMMER
mode without setting the clock.
iPod CONTROL
DISPLAY VOLUME
To confirm the time display:
Press the CLOCK button. The current time and day are
displayed in the front panel display of the stereo receiver for 5
ENTER
seconds.
Note
RETURN
• The current time and day display is canceled if;
PTY RDS DISP MUTE
the volume is adjusted.
-
the SETUP, BASS +/–, TREBLE +/–, DIRECT, or SLEEP
-
button is pressed.
- the stereo receiver is turned off.
the input source for the stereo receiver is changed.
-
To readjust the clock:
Perform "Setting the clock" from step 1.
Note
• If the AC power cord of the stereo receiver is disconnected
from the wall socket, the clock setting is cleared. Set the
clock.
To change the 24-hour or 12-hour display:
1 Clear all the programmed contents.
Refer to Resetting this player on page 36 for details.
2
Perform "Setting the clock" from step 1 onwards.
The time is displayed in the 24-hour
display format (0:00 – 23:59).
The time is displayed in the 12-hour
display format (AM 0:00 – PM
11:59).

General functions

SYSTEM ON RECEIVER CD NETWORK
TIMER
SYSTEM OFF
CONTROL
RCV CD NET TOP
MENU
CD/USB CD USB DIRECT
TREBLE
TUNER BAND FAVORITES
NETWORK M.SERVER NET SERVICE
SETUP
BASS
DIG IN 1/2 iPod/USB BT AUDIO
AUTO TUNE
Display brightness control
Press the CONTROL RCV button on the remote control.
Press DIMMER button to dim the display brightness. The
brightness can be controlled in four steps.
Volume control
Press the VOLUME +/– on the remote control to increase or
decrease volume, or turn the VOLUME knob on the stereo
receiver to the right to increase volume, and to the left to
decrease the volume.
CAUTION
• The sound level at a given volume setting depends on
speaker efficiency, location, and various other factors. It is
advisable to avoid exposure to high volume levels. Do not
turn the volume on to full at switch on. Listen to music at
moderate levels. Excessive sound pressure from earphones
and headphones can cause hearing loss.
Note
• If you turn off and on the stereo receiver with the volume set
to 61 or higher, the volume starts at 60.
• When the DIRECT function is off, the volume can be set
from minimum to 60.
SLEEP CLOCK DIMMER
iPod CONTROL
DISPLAY VOLUME
ENTER
RETURN
PTY RDS DISP MUTE