Wincor Nixdorf BA83 User Manual
  1. Manuals
  2. Brands
  3. Wincor Nixdorf Manuals
  4. Monitor
  5. BA83 /cTouch
  6. User manual

Wincor Nixdorf BA83 User Manual

Lcd tft 15" (38.1 cm) flat panel display
Hide thumbs Also See for BA83:
Table of Contents

Advertisement

Quick Links

See also: User Manual
BA83
LCD TFT 15" (38.1 cm) Flat Panel Display
User Guide

Advertisement

Table of Contents
loading

Related Manuals for Wincor Nixdorf BA83

Summary of Contents for Wincor Nixdorf BA83

  • Page 1 BA83 LCD TFT 15" (38.1 cm) Flat Panel Display User Guide...
  • Page 2 Please send us a copy of this page if you have any constructive criticism. We would like to thank you in advance for your comments. With kind regards. Your Opinion: Wincor Nixdorf International GmbH Dokumentation RD HWD01 Rohrdamm 7 D-13629 Berlin E-Mail: retail.documentation@wincor-nixdorf.com...
  • Page 3 BA83 Flat Panel Display User Guide Edition September 2011...
  • Page 4 All brand and pro duct na mes men tio ned in this do cu ment are tra de marks of their re spec ti ve owners. Co py right© Win cor Nix dorf In ter na tio nal GmbH, 2011 The re pro duc ti on, trans mis si on or use of this do cu ment or its con tents is not per mit ted wit hout ex press aut ho ri ty.

  • Page 5: Table Of Contents

    About This Ma nu al ......2 The Flat Pa nel Dis play BA83 ....3 Ge ne ral .
  • Page 6 Con nec ti on Be zel ......22 Con nec ting the BA83 ......22 Dual Dis play Hol der .
  • Page 7 Dis play Co ding ......65 Cur rent Con sump ti on Of the Screen Mo du le ....66 Pro gram ming the Key bo ard And MSR .

  • Page 8: Introduction

    The low-ener gy, fli cker free and ra di ati on-free co lour mo ni tor of the BA83 is an LCD in TFT-tech no lo gy (Thin Film Tran sis tor).

  • Page 9: Ad Van Ta Ges At A Glan Ce

    (soft wa re and hard wa re), the ope ra ti on and the main ten an ce of your BA83. Some parts of this book re qui re fa mi lia ri ty and ex per ien ce in wor king with ope ra ting sys tems and in stal la ti on and con fi gu ra ti on procedures.

  • Page 10: The Flat Panel Display Ba83

    GENERAL The Flat Panel Display BA83 General The TFT LCD flat panel display is an XGA-com pa ti ble 15-inch flat panel display which is ab so lu te ly fli cker free and free from ra di ati on. It is de sig ned for a re so lu ti on of max.

  • Page 11: Usb Inter Fa Ce

    With this key you can switch the system into ‘Wake up Mode’ or ‘Sleep Mode’ provided a Remote function (see page 18) for the BA83 is availabe (i.e. the cable is connected to a BEETLE system via a remote connector).

  • Page 12: Se Cu Ri Ty

    SE CU RI TY Se cu ri ty The operator panel module can be mounted horizontally turned thus to handicap the access. Slightly press the module inwards at the left and right hand side (1). Remove the module of the recesses and carefully move it off downwards (2).

  • Page 13: Integrated Loudspeakers

    INTEGRATED LOUDSPEAKERS Integrated Loudspeakers The two integrated loudspeakers are located at the bottom side of the screen (see arrows).

  • Page 14: Capacitive Touch Screen

    Connecting a BA83 for the first time, we recommend that you calibrate the Touch Screen. Details depend on the Operating System that you use.

  • Page 15: Clea Ning In Struc Tions

    CLEA NING IN STRUC TIONS Clea ning In struc tions Al ways turn off the sys tem be fo re clea ning. The glass sur fa ce of your Touch Screen should be clea ned with a mild, abrasive free, com mer ci al ly avai la ble glass clea ning pro duct. All pH neut ral ma ter ials (pH 6 to 8) are good for clea ning.

  • Page 16: Infrared Touch Screen

    GE NE RAL Infrared Touch Screen Ge ne ral The infrared (IR) technology is based on the interruption of a grid of IR light beams before the surface of a screen. The touch frame contains a row of infrared light emitting diodes (LEDs) and photo transistors, each mounted on two opposite sides to create a grid of invisible infrared light.

  • Page 17: Clea Ning In Struc Tions

    CLEA NING IN STRUC TIONS Breaking through the grid has the same ef fect as cli cking the left mou se but ton. Therefore, touching the glass is not necessary. To avoid malfunctions: Do not fix labels or stickers on the frame and do not put pencils or the like on the inner frame.

  • Page 18: Swipe Card Reader (Optional)

    HOW TO OPE RA TE Swipe Card Reader (optional) The swi pe card rea der (MSR Mo du le), that is avai la ble as an op ti on, can read three ISO tracks si mul ta ne ous ly in a sing le swi pe.

  • Page 19: Keyboard (Optio N)

    CLEA NING IN STRUC TIONS Keyboard (Optio n) The keyboard is connected directly to the display via a USB interface. It is fitted to the right-hand side of the screen. The keyboard is available with or without a swipe card reader. Clea ning In struc tions The key bo ard should be clea ned with a ger mi ci de from time to time.

  • Page 20: Ex Chan Ging The Keys

    EX CHAN GING THE KEYS Ex chan ging the Keys You can re mo ve each of the key caps using the key re mo val de vi ce en clo sed, pul ling the key up wards. Pla ce the key re mo val de vi ce on the se lec ted key un til you hear a click.

  • Page 21: In Ser Ting Key La Bels

    IN SER TING KEY CAPS In ser ting Key La bels Be low you will find in struc tions on how to in sert the key la bels: Each key should be la bel led in di vi du al ly. You can use the emp ty la bels de li ver ed with the sys tem to do so.

  • Page 22: Swipe Card Reader In A Keyboard (Optional)

    SWIPE CARD READER IN A KEYBOARD (OPTIONAL) When in ser ting dou ble ac tua ting cy lin der keys, plea se en su re that the actuating cy lin der is on the left (horizontally inserted key) resp. on top (vertically insertion).

  • Page 23: Waiter Lock (Optional)

    WAITER LOCK (OPTIONAL) Waiter Lock (optional) Each transaction is correctly as signed to the personell by using the magnetic key. The magnetic keys are available in 10 different colors. The magnet keys are waterproof, shatterproof and by the 16-digit key number also safe for clear identification.

  • Page 24: Installing And Securing

    Wincor Nixdorf sales outlet. Trans port the de vi ce only in its ori gi nal pa cka ging (to pro tect it against im pact and shock).
  • Page 25 TABLE MOUNTING Loosen the four screws on the screen for approx. 2 mm. Put the screen element on to the base. P-USB DVI-I Wincor Nixdorf BA8X/ cTouch 5V/ 12V 017500 000000 0.7A/ 0.7A I.T.E. IC 78+E146247 0199900107 Made in China...

  • Page 26: Table Mounting

    MOUNTING THE TUBE ADAPTER Table Mounting Underneath the cable cover there are two holes in the BA83 stand (see arrows) with a diameter of 5.5 mm. The holes can be used to fix the stand on the footprint with appropriated screws. We recommend using screws with a diameter of 4.0 to 5.0 mm.

  • Page 27: Mounting The Tube Adapter

    For the mounting you need a Phillips head screwdriver for fixing and releasing the screws. Pull the co ver downwards (see pages 16, 17). Loo sen four screws at the rear side of the BA83 and put them asi de. Mount the tube adap ter on the rear...
  • Page 28 MOUNTING THE TUBE ADAPTER Af ter cab ling the dis play put on the op ti nal available co ver. Put the dis play with the adap ter on the preins tal led tube (1) and fix it with the screw (2).

  • Page 29: Connection Bezel

    CONNECTING THE BA83 Connection Bezel The following sockets are located under the bezel of the screen: RJ10/RMT USB- A Po wer edUSB DC Po wer Jack/12 V DVI- I (12) USB- A For external peripherals, can be used for MSR Data transfer and/or current supply for the screen via system e.g.
  • Page 30 DUAL DISPLAY HOLDER When laying this cable please mind to slightly clamp it (with a loop) into the strain relief. Lay the cable into the guidance inside the base. Lay a USB-A cable loosely-fitting into the strain relief. When passing the cables please mind the following maximal cable diameters (in mm).

  • Page 31: Dual Display Holder

    (see installation manual BA8x, Dual Display Holder). Likewise, you can continue a BA82 with another BA82 or a BA82 with a BA83. A clever cable management not only prevents a cable disorder but adds an elegant impression to the device.

  • Page 32: Mounting Positions

    MOUNTING PERIPHERALS Mounting Positions There are three mounting positions.Two (at the left and right hand side) can be used to install Magnetic Card Reader; a keyboard may be installed at the right hand side. The third position is located above the screen. Other units (e.g.

  • Page 33: Ergonomic Terminal Workplace

    MOUNTING PERIPHERALS Ergonomic Terminal Workplace Plea se ob ser ve the fol lo wing when set ting up your ter mi nal work pla ce: Avoid di rect gla ring and re flec ti ve gla ring. Use the screen only in a con trol led lu mi nan ce su roun ding.

  • Page 34: Mounting Peripherals

    Keyboard And Swipe Card Reader The delivery contains the keyboard with Swipe Card Reader (SCR), the connected cable, the pre-installed holder (BA83), the holder of the BA82, two screws and a set of keys including a key remover. key bo ard, SCR, ca ble and hol der BA83...
  • Page 35 MOUNTING PERIPHERALS Loosen the two screws (see arrows) and remove the bracket. Turn the screen around and remove the bezel (see page 17). Loosen the screws beneath the cover. Lift the screen out of the holder to the top. Lay the screen on an appropiate base.
  • Page 36 MOUNTING PERIPHERALS Loosen the snap arms of the loudspeaker's bezel (see arrows). Flap the bezel downwards. Carefully press out the blind screen from inside.
  • Page 37 MOUNTING PERIPHERALS Push the bracket into the opening of the housing, so that the holes are lying upon each other. Tighten with two (delivered) screws. You must always discharge yourself (e. g. by touching a grounded object) before mounting. Take care to pull the connector off the keyboard. Pass the keyboard cable through the housing into the cable guidance and connect it.
  • Page 38 Keyhole Screw Tighten the keyboard. If you are going to use the USB interface at the backside of the BA83 then run the cable loosely through the strain relief as shown below. Put the cable loop into the housing. OSD Ca ble Con nec ti on Key bo ard Ca ble Con nec ti on...
  • Page 39 MAGNETIC SWIPE CARD READER If a device has a second Hub, you can connect the keyboard at the next free port on the Hub. To do so, release the cable's loop and run the cable through the strain relief. Strain re lief USB in ter fa ces (HUB) Insert the cover of the keyboard as shown below.

  • Page 40: Magnetic Swipe Card Reader

    The Magnetic Swipe Card Reader can be mounted on either the right or the left side of the screen. The delivery contains the Swipe Card Reader (SCR), the connected cable, the pre-installed holder (BA83), a holder (BA82) and two screws. SCR, ca ble and hol der BA83 hol der BA82 Do not release the cable loop.

  • Page 41: Moun Ting On The Right Side

    MAGNETIC SWIPE CARD READER Moun ting On the Right Side Loosen the Torx screws and remove the bracket. Turn the screen and remove the cover (see page 17). Loosen and remove the screws beneath the cover. Lift the screen out of the holder to the top.
  • Page 42 MAGNETIC SWIPE CARD READER Loosen the snap arms of the loudspeaker's bezel (see arrows). Flap the blind bezel downwards. Carefully press out the blind screen from inside.
  • Page 43 MAGNETIC SWIPE CARD READER Push the bracket of the Reader into the opening of the housing, so that the holes are lying upon each other. Then tighten it. You must always discharge yourself (e. g. by touching a grounded object) before mounting.
  • Page 44 MAGNETIC SWIPE CARD READER Pass the swipe card reader cable through the housing into the cable guidance and connect it. Push the reader beneath the bracket so that the screws fit into the keyhole and the holder lays under the clamps. Clamp Screw Keyhole...
  • Page 45 MAGNETIC SWIPE CARD READER Pass the cable loosely through the cable guidance and connect it to the USB interface. Put the cable loop into the housing (see big arrow). OSD Ca ble con nec ti on Ca ble con nec ti on for Swi pe Card Mo du le If a device has a second Hub, you can connect the swipe card reader at the next free port on the Hub.

  • Page 46: Moun Ting On The Left Side

    MAGNETIC SWIPE CARD READER Attach the cover of the Swipe Card Reader (1) and push it to the monitor until it engages (2). Flap the loudspeaker's bezel upwards and snap it into place. Mount the monitor's stand. Moun ting On the Left Side Proceed as described above ("Mounting on the right side").
  • Page 47 MAGNETIC SWIPE CARD READER Clamp Push the reader beneath the bracket, so that the screws fit into the keyhole and the holder lays under the clamps. Tighten the screws. Pass the cable through the cable guidance and connect it to the USB interface.

  • Page 48: Waiter Lock

    The delivery contains the waiter lock (1), the connected cable (2), a pre-installed BA83 holder (3); a BA82 holder (4) and two screws (5). Do not release the cable loop. Turn the waiter lock and push the cover sidewards (see arrow).

  • Page 49: Moun Ting On The Right Side

    WAITER LOCK Moun ting on the right Side Loosen the screws of the retain plate. Move the retain plate out of the guide in direction of the arrows and lift it up.
  • Page 50 WAITER LOCK Pull the electronic element out of the housing. You must always discharge yourself (e. g. by touching a grounded object) before mounting. Loosen the screws and pull the plug.
  • Page 51 WAITER LOCK Turn the screen and remove the cover (see page 17). Loosen the 4 mounting screws about 3 mm beneath the cover . Lift up the screen out of the holder to the top. Lay the screen on an appropiate base.
  • Page 52 WAITER LOCK Carefully press out the blind screen from inside.
  • Page 53 OSD Cable connection Cable connection for Swipe Card Module If you are going to use the USB interface at the backside of the BA83 then connect the waiter lock to any free interface at the HUB. To do so, release the cable's loop and run the cable through the strain relief (see page 38).
  • Page 54 WAITER LOCK Plug the jack to the connection of the waiter lock. Screw electronic and element together and clamp it into the housing until it is engaged. Screw the retain plate at the BA83.
  • Page 55 WAITER LOCK Use the left borehole of the two pairs of boreholes to install the retain plate. Put the cable of the waiter lock into the housing. Slip the waiter lock on the retain plate and push it backwards. Make sure that the cable is not crimped. Screw the waiter lock to the retain plate.
  • Page 56 WAITER LOCK Put the housing of the waiter lock on the retain plate and push it until it is engaged. Control the cabling. Flap the loudspeaker's bezel upwards and snap it into place. Mount the monitor's stand.

  • Page 57: Moun Ting On The Left Side

    WAITER LOCK Moun ting on the left Side Proceed as described above ("Mounting on the right side", page 44ff). Fasten the retain plate of the waiter lock on the opening of the housing rotated 180°. Use the right borehole of the two pairs of boreholes to install the retain plate.

  • Page 58: On Screen Display (Osd)

    ON SCREEN DISPLAY (OSD) On Screen Display (OSD) A set of 4 buttons is located at the operator panel module. Power Menu/ left right select scrol ling Pressing the menu button will activate the OSD. Depending on the selected function, a sub- menu option will be available for a selection on the same screen.

  • Page 59: Input Source

    ON SCREEN DISPLAY (OSD) Input Source The Input Source indicates the active video channel B A 8 3 1 0 2 4 x 7 6 8 6 0 H z I n p u t S o u r c e Analog Input (VGA) Digital Input (DVI) Exit sub menu...

  • Page 60: Display Setting

    ON SCREEN DISPLAY (OSD) Display Setting B A 8 3 1 0 2 4 x 7 6 8 6 0 H z D i s p l a y S e t t i n g Brightness Sub menu Contrast Sub menu If the contrast is set too high, bright surfaces can no longer be distinguished from very bright surfaces.

  • Page 61: Colour Setting

    ON SCREEN DISPLAY (OSD) Colour Setting The colour setting is only adjustable in the normal running temperature. The display must run at least 20 minutes. B A 8 3 1 0 2 4 x 7 6 8 6 0 H z A u t o C o l o r Auto Colour (auto colour adjustment at VGA mode only)
  • Page 62 ON SCREEN DISPLAY (OSD) Sub menu colour temperature RGB Setting manual setting There are 5 basic settings: 4200K 5000K 6500K (setting, for example , for image processing or playing DVD) 7500K 9300K (setting for CAD/ CAM applications) Exit sub menu Exit menu...

  • Page 63: Image Setting (Vga- Mode)

    ON SCREEN DISPLAY (OSD) Image Setting (VGA- Mode) B A 8 3 1 0 2 4 x 7 6 8 6 0 H z I m a g e S e t t i n g Auto scaling (auto adjustment) Should the image setting be faulty during the initial operation this function will adjust the image if necessary you operate "Auto colour"...
  • Page 64 ON SCREEN DISPLAY (OSD) Horizontal position Sub menu Vertical position Sub menu Exit sub menu...

  • Page 65: Tools Menu

    ON SCREEN DISPLAY (OSD) Tools Menu B A 8 3 1 0 2 4 x 7 6 8 6 0 H z To o l s M e n u Factory setting No reset of Image Setting (Screen width, phase, horizontal/vertical position) After reset to factory setting at VGA mode: it is absolutely necessary to operate "Auto colour"...

  • Page 66: Volume Setting

    ON SCREEN DISPLAY (OSD) Information about the firmware version Exit sub menu Volume Setting B A 8 3 1 0 2 4 x 7 6 8 6 0 H z V o l u m e S e t t i n g s Volume Sub menu Exit sub menu...

  • Page 67: Exit Osd

    ON SCREEN DISPLAY (OSD) EXIT OSD B A 8 3 1 0 2 4 x 7 6 8 6 0 H z E x i t O S D...

  • Page 68: Technical Data Ba83

    TECHNICAL DATA BA83 Technical Data BA83 Diagonal Screen size 15" (38.1 cm) Active screen size 304 mm x 228 mm (horizontal x vertical) Dimensions Cable length up to 3 m Dimensions Display 368 x 300 x 90 (WxHxD, mm) Housing w/o base 4.5 kg...

  • Page 69: Dimensions (Mm)

    TECHNICAL DATA BA83 Dimensions (mm)

  • Page 70: Capacitive Touch Screen

    TECHNICAL DATA BA83 Capacitive Touch Screen Horizontal Resolutions Vertical Analog capacitive LCD Technology anti-reflection (capacitive) Surface Brightness typ. 200 cd/m² Data transfer Infrared Touch Screen Horizontal 4096 pixel Resolutions Vertical 4096 pixel infrared touch LCD Technology anti-reflection Surface Brightness typ. 220 cd/m²...

  • Page 71: Msr In Si De Key Bo Ard

    TECHNICAL DATA BA83 140 mm Width 40 mm Depth approx. 800 g Weight MSR In si de Key bo ard up to 3 Number of tracks according to ISO 7811-2 Coding of swipe cards 10 to 140 cm/sec. Reading speed MSR Module HID 1.1 (Human Interface Device)

  • Page 72: Screen Driver Installation/ Installation Tool

    The second position on the type label (B) is important for the driver installation. The number marks the used display technology. You find the type label at the rear side of the BA83 under the cable cover. Wincor Nixdorf Ba83/ ...

  • Page 73: Current Consumption Of The Screen Module

    Calibrate the Touch Screen when you connected it for the first time. Current Consumption Of the Screen Module The maximum power input of the BA83 is 2.6 A (12VDc). Power consumption (nominal) < 17 W Power consumption (Standby) <...

  • Page 74: Programming The Keyboard And Msr

    It is, however, possible to program the MSR as well, e.g. if you want to get the same codes for the BA83 MSR (having a USB HID interface) compared to an already existing customer’s MSR (which has e.g. a PS/2 interface).

  • Page 75: Files

    OK rsp. which error occurred. By convention files containing tables have the extension ‘.kbu’. In some cases the power supply to the BA83 would have to be disconnected thus causing a reboot and the import of the new settings. Alternatively, you can use the SW command to activate the "MSR legacy mode".

  • Page 76: Modus

    MODUS Modus Keyboard and MSR may have two different states: “Default” This is the default state of keyboard and MSR, codes are assigned by firmware “Programmed” In this case a table has been sent to keyboard or even MSR Creating Tables Tables can be created and sent / received using KbUtiUSB under Windows or WNLPOS.

  • Page 77: Software Interfaces

    KEY BO ARD CODES (STAN DARD) Software Interfaces Key bo ard Codes (Stan dard) (F1) (F9) (ESC) (BS) Scan Code of the key bo ard con trol ler 3B 00 43 00 01 1B 0E 08 (F2) (F10) 3C 00 44 00 1F 73 16 75...

  • Page 78: Manufacturer's Declaration And Approval

    Tested Safety The BA83 has been awar ded the GS sym bol for “Ge prüf te Si cher heit” (tes ted sa fe ty). BA83 fulfills the re qui re ments for er go no my ac cor ding to ISO 13406-2 and ISO 9241-307.

  • Page 79: User Information

    USER INFORMATION User Information Re pair work on the de vi ces should only be car ried out by aut ho ri zed and spe ci al ly trai ned per son nel. Im pro per re pairs will lead to the loss of any gua ran tee and lia bi li ty claims.

  • Page 80: Instructions For Maintenance

    Instructions For Maintenance Cle an your BA83 regularly with an ap pro pria te sur fa ce clea ning pro duct. Make sure that the de vi ce is swit ched off, con nec tor ca bles are un plug ged and that no moi stu re is al lo wed to get into the in si de of the de vi ce.

  • Page 81: Recycling

    The com pact BA83 is ma nu fac tur ed wit hout the use of CFCs and CCHS and is pro du ced main ly from reu sa ble com po nents and ma ter ials.

  • Page 82: Abbreviation Index

    ABBREVIATION INDEX Abbreviation Index European Symbol of Conformity Canadian Registration (Recognized by UL) Com mu ni ca ti on Port Cen tral Pro ces sing Unit Deutsche Industrie Norm (German Institute for Industrial Standards) DVI-I Digital Visual Interface Integrated Electronic Key Controller Electromagnetic Interference Europäische Norm (European Standard) Electrostatic Discharge...
  • Page 83 Herausgegeben von/Published by Wincor Nixdorf International GmbH D-33094 Paderborn Bestellnummer/Order No. 01750158764F Printed in Singapore...

Table of Contents