Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for Intelix DIGI-VGASD-8X8e
Summary of Contents for Intelix DIGI-VGASD-8X8e
- Page 1 DIGI-VGASD-8X8e 8 input by 8 output Matrix Switcher...
-
Page 2: Table Of Contents
Intelix DIGI-VGASD-8X8e Installation Manual Table of Contents Overview ..................... 4 Installation ..................5 Controlling the Matrix ................ 8 Transmitting Control Signals ............17 Using the Matrix with Video Signals other than VGA ...... 22 Technical Specifications ..............23 Warranty .................... 24 Contact Information…………………………………………………... -
Page 3: Important Safety Instructions
Do not block the air ventilation openings. Only mount the equipment per Intelix’s instructions. Use only with the cart, stand, tripod, bracket, table, or rack specified by Intelix or sold with the equipment. When/if a cart is used, use caution when moving the cart/equipment combination to avoid injury from tip-over. -
Page 4: Overview
350 feet on a single twisted pair cable. In essence, the DIGI-VGASD-8X8e allows you to switch audio, video, and control and transmit it all over a single twisted pair cable to a remote Intelix DIGI- VGASD Series receiver. -
Page 5: Installation
Intelix DIGI-VGASD-8X8e Installation Manual Installation To install the Intelix DIGI-VGASD-8X8e matrix switcher, please perform the following steps. 1. If mounting in a 19” audio/video rack, verify the rack has one rack space unit (1RU) of open space. Ventilation when Rack Mounting ... - Page 6 350 feet YPbPr, audio, IR, RS232 *Note that the DIGI-VGASD-8X8e is not a scaler. Like inputs must be routed to like outputs; i.e., VGA inputs must be routed to VGA receivers, component video inputs must be routed to component video receivers, etc.
- Page 7 5. Connect the included power cord to the DIGI-VGASD-8X8e. 6. Connect an RS232 cable to the DIGI-VGASD-8X8e. Verify the opposite end of the cable is connected to a controller (i.e., PC running Intelix Smart Control software, touch panel, etc.). Note: If controlling the DIGI-VGASD-8X8e matrix with Intelix Smart Control software, verify the software is properly loaded on a connected PC.
-
Page 8: Controlling The Matrix
Intelix Smart Control software is included with each DIGI-VGASD-8X8e matrix purchase. In order to install Intelix Smart Control software, please follow the steps below. 1) Insert the Intelix Software CD into the computer’s CD-ROM drive. 2) The CD should automatically start, and the Intelix Autorun Wizard window should initiate. - Page 9 Intelix DIGI-VGASD-8X8e Installation Manual After installation, execute the Intelix Smart Control software on the computer. 1) The first screen will prompt you to load an existing configuration. If you have a pre-configured file, select Yes. If you are creating a new file, select No.
- Page 10 Intelix DIGI-VGASD-8X8e Installation Manual 4) Select the Intelix DIGI-VGASD series matrix type for each router in the application. 5) Define the quantity of inputs and outputs for each router in the application. 6) Select the Communication Port your computer or control system is using to connect to the DIGI-VGASD-8X8e matrix.
- Page 11 Note: Intelix Smart Control software allows each input and output to be custom labeled. Select the desired input/output and enter your label. 9) Intelix Smart Control Pro software provides control routing at each individual crosspoint. To route a signal, select the circle where the input and output meet.
- Page 12 Intelix DIGI-VGASD-8X8e Installation Manual For example, the Lab Computer may be routed to LCD 3 by selecting the third crosspoint from the left on the top row. Note: Inputs may be routed simultaneously to multiple outputs, but each output may only view a single input.
- Page 13 Intelix DIGI-VGASD-8X8e Installation Manual 10) To record a routing sequence as a preset, or macro, select the Record button under the Macro header. A blinking recording message will appear. Note: A macro records your clicks in the software. 11) Select the desired crosspoints in the preset. There is no limit on preset routing.
- Page 14 Intelix DIGI-VGASD-8X8e Installation Manual To cancel saving a macro, select the Cancel Save button. 12) Intelix Smart Control software provides up to 50 saved macros. To recall a macro, select it from the column in the Smart Control Pro screen.
- Page 15 Exclusive OR (XOR) of all previous bytes <CR> Carriage return (0Dh); all commands sent from a PC end with <CR> * CRC protocol can be disabled through the Intelix Smart Control software or by sending the following command: CRCOFF <CR> Example Routing Command Requirement...
- Page 16 Intelix DIGI-VGASD-8X8e Installation Manual Routing RS232 from Specific Sources to Specific Destinations The DIGI-VGASD-8X8e matrix allows RS232 commands to be transmitted from an individual input to an individual output. Code Description //FxxRyyIzz<CHK><CR> Connect to a crosspoint //FxxDyyIzz<CHK><CR> Disconnect to a crosspoint //FxxFnn<CHK><CR>...
-
Page 17: Transmitting Control Signals
Intelix DIGI-VGASD-8X8e Installation Manual Transmitting Control Signals The DIGI-VGASD-8X8e transmits bi-directional RS232 and IR over the same twisted pair output cable used for audio and video. RS232 and IR operate in different manners, and the DIGI-VGASD-8X8e handles each signal differently. - Page 18 Intelix DIGI-VGASD-8X8e Installation Manual 1. Connect the desired controller to the DIGI-VGASD-8X8e matrix using an RS232 (serial) cable. Serial Connector Pinout 2. Verify the communication baud rate is 115,000 kbps or less. www.intelix.com...
- Page 19 Intelix DIGI-VGASD-8X8e Installation Manual IR Transmission The DIGI-VGASD-8X8e features independent IR transmission for each of the matrix’s eight channels. Unlike RS232, IR is not bi-directional; the Intelix DIGI-VGASD-8X8e transmits IR signals from the remote twisted pair receiver back to the matrix. The signal is then output to the active audio/video channel;...
- Page 20 Intelix DIGI-VGASD-8X8e Installation Manual 1. Verify a remote Intelix twisted pair receiver is connected to the DIGI- VGASD-8X8e matrix via twisted pair cable. 2. Connect an Intelix DIGI-VGASD-IREYE IR receiver (sold separately) to the twisted pair receiver. 3. Connect an Intelix DIGI-VGASD-IREMT IR emitter (sold separately) directly to the DIGI-VGASD-8X8e.
-
Page 21: Using The Matrix With Video Signals Other Than Vga
Using the Matrix with Video Signals other than VGA Even though the Intelix DIGI-VGASD-8X8e features HD15 (traditional VGA) style connectors, the matrix supports video formats other than VGA. Component video, composite video, and Y/C video may all be routed through the matrix;... - Page 22 Intelix DIGI-VGASD-8X8e Installation Manual Intelix manufactures adaptor cables to convert an HD15 connector to component video, composite video, and Y/C video standards. Each converted input requires a conversion cable. Conversion Cables BRKOUT-KIT Converts (1) female HD15 connector to (5) male BNC...
-
Page 23: Technical Specifications
Operating Humidity Range ..........5 to 90% non-condensing Dimensions ................. 19.00” x 1.25” x 9.25” 1 RU Enclosure ..................... Black metal Regulatory ..................... CE, RoHS Compatible Intelix Twisted Pair Receivers ........ DIGI-VGASD-R DIGI-VGASD-WP-R DIGI-V3A2-R DIGI-V3SD-R Shipping Weight ................... 12 lbs Intelix Part Number .............. -
Page 24: Warranty
No agent or reseller of Intelix is authorized to modify this warranty or to make additional warranties on behalf of Intelix. Statements, representations or warranties made by any party other than Intelix does not constitute warranties by Intelix. - Page 25 All other standard warranty limitations apply. *Or current applicable rate/fee. Warranty terms and conditions subject to change and do not apply outside of United States and Canada. Intelix Warranty is subject to change. Please contact the factory for the most up-to-date information. www.intelix.com...
-
Page 26: Contact Information
Intelix DIGI-VGASD-8X8e Installation Manual Thank you for your purchase. We appreciate your business. Please contact us with your questions and comments. Intelix 2222 Pleasant View Road Suite 1 Middleton, WI 53562 Phone: 608-831-0880 Toll-Free: 866-4-MATMIX Fax: 608-831-1833 www.intelix.com intelix@intelix.com Copyright 2009 Intelix LLC. - Page 27 Intelix DIGI-VGASD-8X8e Installation Manual www.intelix.com...
Need help?
Do you have a question about the DIGI-VGASD-8X8e and is the answer not in the manual?
Questions and answers