Locking Channels; Locking The Video Inputs - Toshiba 42HP86 Owner's Manual

Locking channels

With the CH LOCK feature, you can lock specific channels. You will not
be able to tune locked channels unless you clear the setting. You can
choose to lock up to six TV channels and six cable channels.
1. Press TV to select the TV mode.
2. Use the Channel Number buttons (0-9 and 100) to display the
television channel you wish to lock.
3. Press MENU, then press
4. Press ▲ or ▼ to display the password entering mode.
5. Use the Channel Number buttons
(0-9) to enter your password, then
press ENTER. The LOCKS menu
appears.
6. Press ▲ or ▼ to highlight CH LOCK
and press to display the CH LOCK
menu.
7. Press or to select SET to set the
channel as one to be locked. Then
press ENTER.
8. Repeat steps 1 through 7 to lock
other channels. When you are
finished locking channels, press EXIT
to return to normal viewing.
If you try to tune a locked channel, the TV will not display it, but will
display the nearest unlocked channel.
To unlock channels:
1. Press TV to select the TV mode.
2. Press MENU, then press
3. Press ▲ or ▼ to display the password entering mode.
4. Use the Channel Number buttons (0-9) to enter your password,
then press ENTER. The LOCKS menu appears.
5. Press ▲ or ▼ to highlight CH LOCK and press
the CH LOCK menu.
6. Press or to highlight CLEAR and clear all channels from the
list of locked channels. Press ENTER.
7. Press EXIT to return to normal viewing.

Locking the video inputs

With the VIDEO LOCK feature, you can lock out the input sources
(VIDEO-1~3, ColorStream HD-1/2, HDMI-1/2, PC) and channels 3 and
4. You will not be able to select the input sources with the INPUT button
or Channel Number buttons unless you clear the setting.
To set up the video lock:
1. Press TV to select the TV mode.
2. Press MENU, then press
3. Press ▲ or ▼ to display the password entering mode.
4. Use the Channel Number buttons (0-9) to enter your password,
then press ENTER. The LOCKS menu appears.
5. Press ▲ or ▼ to highlight VIDEO
LOCK.
6. Press or to select:
• OFF: Unlocks all video input
sources.
• VIDEO: Locks VIDEO-1~3,
ColorStream HD-1/2, HDMI-1/2,
PC.
• VIDEO +: Locks VIDEO-1~3, ColorStream HD-1/2, HDMI-1/2,
PC, channel 3 and channel 4. This option should be used if you
use the antenna terminal to play a video tape.
7. Press EXIT to return to normal viewing.
To unlock the video inputs:
Select OFF in step 6, above.
30A0121A_En_p26-30 27
or to display the LOCKS menu.
L O C K S
L O C K
C H L O C K
V I D E O L O C K O F F
: S E L E C T : A D J U S T
CH LOCK : CH 002
SET / CLEAR TV CABLE
LOCKED CH 0
002
0 0
RETURN
SELECT ADJUST
ENTER:SET
or to display the LOCKS menu.
or to display
or to display the LOCKS menu.
L O C K S
L O C K
C H L O C K
O F F
V I D E O L O C K
O F F / V I D E O / V I D E O +
: S E L E C T : A D J U S T
27
INPUT DISPLAY
0
0
Note:
After programming CH LOCK, change
channels before turning off the television.
INPUT DISPLAY
Note:
After programming VIDEO LOCK, change
channels or press INPUT before turning off
the television.
Note:
If the remote control does not operate your TV,
press the "TV" button on the remote control
and try again.
06.5.30, 3:35 PM
Channel
Numbers
TV
Menu/Enter
Exit
Input
Channel
Numbers
TV
Menu/Enter
Exit