Locking Channels; Locking The Video Inputs - Toshiba 42HP66 Owner's Manual

÷
÷
Locking channels
With the CH LOCK feature, you can lock specific channels. You will not
be able to tune locked channels unless you clear the setting. You can
choose to lock up to nine TV channels and nine cable channels.
1. Press TV to select the TV mode.
2. Use the Channel Number buttons (0-9 and 100) to display the
television channel you wish to lock.
3. Press MENU, then press 4 or _ to display the LOCKS menu.
4. Press • or • to display the password entering mode.
5. Use the Channel Number buttons
(0-9) to enter your password, then
LOCKS
press ENTER. The LOCKS menu too,
appears. _v,oEo LOOK _ o_
6. Press • or • to highlight CH LOCK
and press 1_ to display the CH LOCK ,., ......... _.......
menu.
7. Press _1 or _ to select the following:
• SET: to set the channel as one to be ..........
locked. Then press ENTER.
• CLEAR: to clear all channels from
RETURN
the list of locked channels. Then _........
@.ADJUST
ENTER:SET
press ENTER.
8. Repeat steps 1 through 7 to lock other channels. When you are
finished locking channels, press EXIT to return to normal viewing.
If you try to tune a locked channel, the TV will not display it, but will
display the nearest unlocked channel.
To unlock channels:
1. Press TV to select the TV mode.
2. Press MENU, then press _11 or _- to display the LOCKS menu.
3. Press • or • to display the password entering mode.
4. Use the Channel Number buttons (0-9) to enter your password,
then press ENTER. The LOCKS menu appears.
5. Press • or • to highlight CH LOCK and press I_ to display the
CH LOCK menu.
6. Press ,_ or _ to highlight CLEAR and clear all channels from the
list of locked channels. Press ENTER.
7. Press EXIT to return to normal viewing.
Locking the video inputs
With the VIDEO LOCK feature, you can lock out the input sources
(VIDEO-1-3, ColorStream HD-1/2, HDMI-1/2, PC) and channels 3 and
4. You will not be able to select the input sources with the INPUT button
or Channel Number buttons unless you clear the setting.
To set up the video lock:
1. Press TV to select the TV mode.
2. Press MENU, then press _t or P- to display the LOCKS menu.
3. Press • or • to display the password entering mode.
4. Use the Channel Number buttons (0-9) to enter your password,
then press ENTER. The LOCKS menu appears.
5. Press • or • to highlight VIDEO
LOCK.
6. Press _ or _- to select: .....
A
LOCK
• OFF: Unlocks all video input
sources.
• VIDEO: Locks VIDEO-1-3, ,,_ . ....... _.......
ColorStream HD-1/2, HDMI-1/2,
PC.
• VIDEO +: Locks VIDEO-I-3, ColorStream HD-1/2, HDMI-1/2,
PC, channel 3 and channel 4. This option should be used if you
use the antenna terminal to play a video tape.
7. Press EXIT to return to normal viewing.
To unlock the video inputs:
Select OFF in step 6, above.
28
-- Channel
Numbers
-- TV
-- Menu/Enter
-- Exit
Note:
After programming CH LOCK, change
channels before turning off the television.
--
Input
-- Channel
Numbers
-- TV
Menu/Enter
__
Exit
Note:
After programming VIDEO LOCK, change
channels or press INPUT before turning off
the television.
Note:
If the remote control does not operate your TV,
press the "TV" button on the remote control
and try again.
÷
3X70121A En p26-31 28 _ 1/31/06,10:59 PM