Kenmore 134313400 Use And Care Manual

Coin- operated commercial ryer

Advertisement

®
Coin- Operated
Commercial
ryer
i
ModeJs" 64182, 74182
PIN 134313400D
(0712)
Sears, Roebuck and Co., Hoffman Estates, IL 60179 U.S.A.
www.sears.com

Advertisement

Table of Contents
loading

Summary of Contents for Kenmore 134313400

  • Page 1 ® Coin- Operated Commercial ryer ModeJs" 64182, 74182 PIN 134313400D (0712) Sears, Roebuck and Co., Hoffman Estates, IL 60179 U.S.A. www.sears.com...
  • Page 2 Sears Service (1-800-469-4663) SERVICE or PARTS your washer: be ready to give the model the installation and ensure the dryer for future reference. and the latest edition immediately follow instructions. follow instructions. Kenmore Record of the of the...
  • Page 3 United States must also comply with the Outline for Clothes Dryer Transition Duct, UL standard 2158A. venting materials are known to collapse, be easily crushed and trap lint. These conditions will obstruct clothes dryer airflow and increase the risk of fire, any lint prior to installing...
  • Page 4: Gas Supply Requirements

    Exceeding the length of duct pipe or number of elbows allowed in the "MAXIMUM cause an accumulation of lint in the exhaust system. Plugging the system could create a fire hazard, aswell as increase drying times. Do not screen the exhaust ends of the vent system, nor use any screws, rivets or other fastening means that extend into the duct and catch lint to assemble the exhaust system.
  • Page 5: Rear View

    ROUGH-IN DIMENSIONS ._---_267/8" (68.3 crn) 43/8" 1.2cm) ELECTRIC CONNECTION REAR ViEW 2 9116"---_ (6.5 cm) 13 1/2" 3/8" (0.96 cm) DIA. 3 314' (9.5 cm) 47 1/2" (120.7 cm) DOOROPEN900 SIDE ViEW 4 318" (11.1 cm) OPTIONAL VENTKNOCKOUT (68.6 cm) (Figure UNPACKING 1.
  • Page 6 DO NOTINSTALL YOUR DRYER: 1. in an area exposed to dripping water or outside weather conditions. 2. In an area where it will come in contact with curtains, drapes, or anything that will obstruct the flow of combustion and ventilation air. 3.
  • Page 7: Grounding Requirements

    ELECTRICAL INSTALLATION Before proceeding with electrical installation, install the dryer's coin-metering system (when used)in accordance with the separate instructions provided with the meter. /ILL ELECTR/CDryers The following are specific requirements for proper and safe electrical installation to follow these instructions can create electrical shock and/ or a fire hazard.
  • Page 8 ELECTRICALCONNECTIONS FOR 3-WIRE SYSTEM ELECTR/CDryer 1. Remove the screws securing the terminal block access cover and the strain relief mounting bracket located on the back of the dryer upper corner. 2. Install a U.L. listed strain relief into the power cord entry hole of the mounting bracket.
  • Page 9 INSTALLATION GAS CONNECTION (Gas dryers only) a. Remove the shipping cap from gas pipe at the rear of the dryer. NOTE: DO NOTconnect the dryer to L.R gas service without converting the gas valve. An L.R conversion kit must be installed by a qualified gas technician. Connect a 1/2 inch (1.27 cm)I.D, semi-rigid or approved pipe from gas supply line to the 3/8 inch (0.96 cm) pipe located on the back of the dryer.
  • Page 10 REPLACING NYLON TIMING CAMS ON ACCUMULATOR MECHANISM Electrical Shock Hazard • Disconnect both power supply cords from the electric power supply before making these changes. Change timing cams before completing connection. Failure to do so could result in electrical shock or personal injury. A.
  • Page 11 * Pull coin slide out of coin chute (see FIGURE4). STEP4 Turn coin slide upside down and remove screw that holds coin receiver block (see FIGURE 5). (1) Receiver Block Screw STEP5 Remove coin receiver block from coin slide (see FIGURE 6): * Turn coin slide right side up.
  • Page 12 To remove block-out keys, pull straight up. NOTE: Be sure block-out keys and/or dime inserts are seated properly and ratchet dog is in place with its spring connected (see FIGURE8). Be sure the proper coin sizing block is in place. Block-Out Keys FIGURE 8...
  • Page 13 eter Case Parts List Parts List For Greenwald Dryer Timers Timer Assembly Model 50-1232=9 ITEM PART NUMBER 50-61-13-2 51-16!-4 00-6164 *Additional 51-161-1 cams that 51-161-2 are available. 51-161-3 Cams pull 51-161-5 51-161-6 off and push on for 51-161-7 51-161-8 replacement. 51-161-9 51-161-10 51-161-1!
  • Page 14 V8 Parts List DESCRIPTION ___o.3o2o_ _20_300_0_ SCREW (METRIC) 00-972_44 00-7924 _1 °° 793_4 00_7936 SCREW (METRIC) _120 30194 20_3002 TOP HOUSING _!120 204_ ... SHIM _120 3006_ 20 3 006 COIN SIZING BLOCK _120 2°434 20 2 006 GATE COVER _12°...
  • Page 15: Dryer Warranty

    To change vend price, detach and mail the lower portion to: Customer Service Department Greenwald industries inc. 212 Middlesex Ave. Chester, CT 06412 The coin chute has been pre-set at the factory. When increasing in $.25 pricing Follow product information instructions; no extra parts required. When decreasing in $.25 pricing - or - changing $.10 pricing.
  • Page 16 For expert troubleshooting For repair - in your home - of all major brand appliances, lawn and garden equipment, no matter who made it, no matter who sold it! For the replacement owner's manuals that you need to do-it-yourself. For Sears professional and items like garage door openers and water heaters.

Table of Contents