Related Manuals for Dynamix 4-Band VDSL CO/CPE Modem
Summary of Contents for Dynamix 4-Band VDSL CO/CPE Modem
- Page 1 4-Band VDSL CO/CPE MODEM USER’S MANUAL Ver. A.2 4-Band VDSL CO/CPE Modem USER’S MANUAL...
-
Page 2: Vdsl Point To Point Solution
4-Band VDSL CO/CPE MODEM USER’S MANUAL Ver. A.2 Best viewed at full screen. VDSL Point to Point Solution The 4-BAND VDSL CO MODEM works as Ethernet to/from VDSL subscriber-site conversion bridge. The 4-BAND VDSL CO MODEM uses QAM-based 4-band VDSL technology which supports max distance of 1.9km (6333ft) at 5M/5M or 1.3km (4333ft) at 15M/15M, or 800m (2666ft) at 25M/25M symmetrical data service. -
Page 3: Table Of Contents
4-Band VDSL CO/CPE MODEM USER’S MANUAL Ver. A.2 Table of Contents VDSL Point to Point Solution………………………………………………………………………………………………2 1. Unpacking Information…………………………………………………………………………………………………..4 2. Installing the Modem……………………………………………………………………………………………………..5 Hardware Installation………………………………………………………………………………………………………..5 Pre-installation Requirements……………………………………………………………………………………………..5 General Rules…………………………………………………………………………………………………………………5 Connecting the Modem……………………………………………………………………………………………………..6 Connecting the RJ-11 / RJ-45 Ports………………………………………………………………………………………7 3. Hardware Description…………………………………………………………………………………………………….9... -
Page 4: Unpacking Information
4-Band VDSL CO/CPE MODEM USER’S MANUAL Ver. A.2 1. Unpacking Information Check List Carefully unpack the package and check its contents against the checklist. Package Contents VDSL 4-Band Modem (4-BAND VDSL CO MODEM for CO side/ 4-BAND VDSL CPE MODEM for CPE side) -
Page 5: Installing The Modem
4-Band VDSL CO/CPE MODEM USER’S MANUAL Ver. A.2 2. Installing the Modem Hardware Installation This chapter describes how to install the Modem and establishes network connections and may install the Modem on any level surface (e.g. a table or shelf). However, please take note of the following minimum site requirements before one begin. Stick the 4 plastic feet at the bottom to avoid scratches. -
Page 6: General Rules
4-Band VDSL CO/CPE MODEM USER’S MANUAL Ver. A.2 General Rules Before making any connections to the modem, please note the following rules: Ethernet port (RJ-45) All network connections to the modem Ethernet port must be made using Category 5 UTP for 100Mbps; Category 3 and 4 UTP for 10Mbps. -
Page 7: Connecting The Rj-11/Rj-45 Ports
4-Band VDSL CO/CPE MODEM USER’S MANUAL Ver. A.2 Connecting the RJ-11/RJ-45 Ports The Modem’s RJ-11 ports support max distance 1.9km at 5M/5M or maximum speed at 25M/25M symmetrical and distances up to 800m data service across existing phone wiring without interfering with standard voice transmissions, easy-to-use does not require the installation of any additional wiring. - Page 8 4-Band VDSL CO/CPE MODEM USER’S MANUAL Ver. A.2 4-BAND VDSL CO MODEM has embedded splitter between every VDSL side (Line) and POTS (Phone) side. It permits you to deliver broadband service on the same lines as Plain Old Telephone Service (POTS), PBX, ISDN traffic and VDSL Signal.
-
Page 9: Hardware Description
4-Band VDSL CO/CPE MODEM USER’S MANUAL Ver. A.2 3. Hardware Description This section describes the important parts of the modem. It features the front panel, side panel and rear connectors. Front Panel The figure shows the front panel. 4-BAND VDSL CO MODEM... - Page 10 4-Band VDSL CO/CPE MODEM USER’S MANUAL Ver. A.2 Front Indicators The modem has Five LED indicators. The following Table shows the description. (Table 1) LEDs Status Descriptions It will light up (ON) to show that the product is Steady power good, and system reset OK.
-
Page 11: Rear Panel
4-Band VDSL CO/CPE MODEM USER’S MANUAL Ver. A.2 Rear Panel The following figure shows the rear connectors. (Figure3) Figure 3: Rear Connectors The table shows the rear modem connectors, description and type. (Table2) Connectors Description Type For connecting to the VDSL Modem... -
Page 12: Side Panel
4-Band VDSL CO/CPE MODEM USER’S MANUAL Ver. A.2 Side Panel The following figure shows the DIP switch connection. (Figure 4) Figure 4: Side Panel At quick glance, it is easy to see that the DIP switch pin 1 is switch ON where it is in auto-speed and that is also the default mode. - Page 13 4-Band VDSL CO/CPE MODEM USER’S MANUAL Ver. A.2 To set the data speed to 25Mbps simply switch ON pin 2 while the other pins are in reset mode. To change it to 15Mbps, switch ON the pin 3 while the other pins are in reset mode and for 5Mbps switch on the pin 4 while other are in reset mode. Remember that no two pins can be activated at the same time or it will result in error and for data speed of 5Mbps.
-
Page 14: Firmware Description
4-Band VDSL CO/CPE MODEM USER’S MANUAL Ver. A.2 4. Firmware Description Auto and manual data speed selector description: 4-Band VDSL CO modem is a 4 band VDSL solution which supports real plug & play and can do auto and manual selection of the data speed, the setting of the data speed depends on the phone cable limit, they can support 5M/15M/25M symmetrical data service but depends on installation environment. -
Page 15: Appendix A: Cable Requirements
4-Band VDSL CO/CPE MODEM USER’S MANUAL Ver. A.2 Appendix A: Cable Requirements A CAT 3, 4 or 5 UTP (Unshielded Twisted Pair) cable is typically used to connect the Ethernet device to the modem. A 10Base-T cable often consists of four pairs of wires, two of which are used for transmission. The connector at the end of the 10Base-T cable is referred to as an RJ-45 connector and it consists of eight pins. - Page 16 4-Band VDSL CO/CPE MODEM USER’S MANUAL Ver. A.2 Standard telephone wire of any gauge or flat type, twisted or quad is used to connect the modem to the telephone network. A telephone cable typically consists of three pairs of wires, one of which is used for transmission. The connector at the end of the telephone cable is called an RJ-11 connector and it consists of six pins.
-
Page 17: Appendix B: Product Features And Specification
4-Band VDSL CO/CPE MODEM USER’S MANUAL Ver. A.2 Appendix B: Product Features & Specification Product Name：4-BAND VDSL CO/CPE MODEM Features: Compliant with IEEE802.3 10BASE-T standard. Compliant with IEEE802.3u 100BASE-TX standard. Compliant with ETSI, ITU, ANSI standards Max speed 5M/5M with distance up to 1.9km(6333ft) Max speed 15M/15M with distance up to 1.3km(4333ft) - Page 18 4-Band VDSL CO/CPE MODEM USER’S MANUAL Ver. A.2 Specifications: Standard IEEE802.3 standard IEEE802.3u standard Compliant with ETSI, ITU & ANSI standards Interface 1 * RJ-45 10/100Mbps Ethernet port 1 * RJ-11 connector for EoVDSL 1 * RJ-11 connector for telephone connection...
-
Page 19: Appendix C: Troubleshooting
4-Band VDSL CO/CPE MODEM USER’S MANUAL Ver. A.2 Appendix C: Troubleshooting Diagnosing the Modem’s Indicators The Modem can be easily monitored through its comprehensive panel indicators. These indicators assist the network manager in identifying problems the hub may encounter. This section describes common problems you may encounter and possible solutions. - Page 20 4-Band VDSL CO/CPE MODEM USER’S MANUAL Ver. A.2 when both are power on. 4-BAND VDSL CO Modem will do auto speed function depending on phone wire length, therefore if 4-BAND VDSL CO Modem can’t detect 4-BAND VDSL CPE Modem over phone wire while both power on, this will cause the link to fail.
- Page 21 4-Band VDSL CO/CPE MODEM USER’S MANUAL Ver. A.2 Power and Cooling Problems If the POWER indicator does not turn on when the power cord is plugged in, you may have a problem with the power outlet, power cord, or internal power supply as explained in the previous section. However, if the unit power is off after running for a while, check for loose power connections, power losses or surges at the power outlet, and verify that the fan on back of the unit is unobstructed and running prior to shutdown.
- Page 22 4-Band VDSL CO/CPE MODEM USER’S MANUAL Ver. A.2 Physical Configuration If problems occur after altering the network configuration, restore the original connections, and try to track the problem down by implementing the new changes, one step at a time. Ensure that cable distances and other physical aspects of the installation do not...
-
Page 23: Appendix D: Compliance And Safety Information
4-Band VDSL CO/CPE MODEM USER’S MANUAL Ver. A.2 Appendix D：Compliance and Safety Information FCC Radio Frequency Interference Statement This equipment has been tested and found to comply with the limits for a computing device, pursuant to Part 15 of FCC rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. - Page 24 4-Band VDSL CO/CPE MODEM USER’S MANUAL Ver. A.2 Important Safety Instructions Caution：The direct plug-in wall transformer serves as the main disconnect for the product. The socket outlet shall be installed near the product and be readily accessible. Caution：Use only the power supply included with this product. In the event the power supply is lost or damaged：In the United States, use only with CSA certified or UL listed Class 2 power supply, rated 5Vdc 1A or above.
-
Page 25: Warranty
4-Band VDSL CO/CPE MODEM USER’S MANUAL Ver. A.2 CE Mark Warning This is a CE class A product. In a domestic environment, this product may cause radio interference in which case the user may be required to take adequate measures.