Download Table of Contents Print this page

Panasonic KX-TDE100 Installation Manual

Pure ip-pbx
Hide thumbs Also See for KX-TDE100:

Advertisement

Table of Contents
Thank you for purchasing a Panasonic Pure IP-PBX.
Please read this manual carefully before using this product and save this manual for future use.
KX-TDE100/KX-TDE200: PMMPR Software File Version 1.0000 or later
Pure IP-PBX

Installation Manual

KX-TDE100
Model No.
KX-TDE200
SD Logo is
a trademark.

Advertisement

Table of Contents
loading

Related Manuals for Panasonic KX-TDE100

Summary of Contents for Panasonic KX-TDE100

  • Page 1: Installation Manual

    Model No. KX-TDE200 Thank you for purchasing a Panasonic Pure IP-PBX. Please read this manual carefully before using this product and save this manual for future use. SD Logo is KX-TDE100/KX-TDE200: PMMPR Software File Version 1.0000 or later a trademark.
  • Page 2: System Components

    System Components System Components Table Category Model No. Description Shelves KX-TDE100 Basic Shelf KX-TDE200 Basic Shelf Main Processing Card IP Convergence Main Processing Card (IPCMPR) IPCMPR Option Cards KX-TDE0110 16-Channel VoIP DSP Card (DSP16) KX-TDE0111 64-Channel VoIP DSP Card (DSP64)
  • Page 3 System Components Table Category Model No. Description Physical Trunk Cards KX-TDA0180 8-Port Analogue Trunk Card (LCOT8) KX-TDA0181 16-Port Analogue Trunk Card (LCOT16) KX-TDA0182 8-Port DID Card (DID8) KX-TDA0183 4-Port Analogue Trunk Card (LCOT4) KX-TDA0184 8-Port E & M Trunk Card (E&M8) KX-TDA0187 T-1 Trunk Card (T1) KX-TDA0188...
  • Page 4 S/M-type Back-up Battery Cable KX-A229 L-type Back-up Battery Cable KX-A258 Blank Slot Cover KX-T30865 Doorphone Compatible Panasonic Proprietary Telephones The PBX supports the following telephones: • IP proprietary telephones (e.g., KX-NT300 series) • IP softphones (e.g., KX-NCS8100) • Digital proprietary telephones (e.g., KX-T7600 series) •...
  • Page 5 • Notice • Some optional service cards and features are not available for certain countries/areas. Consult your certified Panasonic dealer for detailed instructions. • In this manual, the suffix of each model number (e.g., KX-TDE100NE) is omitted unless necessary. •...
  • Page 6: Important Safety Instructions

    Important Safety Instructions SAFETY REQUIREMENTS When using your telephone equipment, basic safety precautions should always be followed to reduce the risk of fire, electric shock and injury to persons, including the following: Read and understand all instructions. Follow all warnings and instructions marked on the product. Unplug the product from the wall outlet before cleaning.
  • Page 7 SAVE THESE INSTRUCTIONS Installation Manual...
  • Page 8 Contact your telephone company. If all SLTs operate properly, there may be a problem with your PBX. Do not reconnect the PBX to the trunks until it has been serviced by an authorised Panasonic Factory Service Centre. • Wipe the unit with a soft cloth. Do not clean with abrasive powders or with chemical agents such as benzene or thinner.
  • Page 9 For users in Germany only • Machine Noise Information Ordinance, 3rd GPSGV: The highest sound pressure level is 70 dB (A) or less according to EN ISO 7779. For users in Finland, Norway and Sweden only • This unit may only be installed in a room or space with restricted access, and equipotential bonding must be applied.
  • Page 10 UNPLUG THIS UNIT FROM THE AC OUTLET IF IT EMITS SMOKE, AN ABNORMAL SMELL OR MAKES UNUSUAL NOISE. THESE CONDITIONS CAN CAUSE FIRE OR ELECTRIC SHOCK. CONFIRM THAT SMOKE HAS STOPPED AND CONTACT AN AUTHORISED PANASONIC FACTORY SERVICE CENTRE. • WHEN RELOCATING THE EQUIPMENT, FIRST DISCONNECT THE TELECOM CONNECTION BEFORE DISCONNECTING THE POWER CONNECTION.
  • Page 11 • THE SD MEMORY CARD POSES A CHOKING HAZARD. KEEP THE SD MEMORY CARD OUT OF REACH OF CHILDREN. For Future Reference Please print, record, and retain the following information for future reference. Note The serial number of this product can be found on the label affixed to the unit. You should record the model number and the serial number of this unit as a permanent record of your purchase to aid in identification in the event of theft.
  • Page 12 Radio & Telecommunications Terminal Equipment (R&TTE) Directive 1999/5/EC. Declarations of Conformity for the relevant Panasonic products described in this manual are available for download by visiting: http://www.doc.panasonic.de...
  • Page 13: Installation Manual

    Introduction This Installation Manual is designed to serve as an overall technical reference for the Panasonic Pure IP- PBX, KX-TDE100/KX-TDE200. It provides instructions for installing the hardware, and programming the PBX using the KX-TDE Maintenance Console. The Structure of this Manual...
  • Page 14 • All other trademarks identified herein are the property of their respective owners. • Screen shots reprinted with permission from Microsoft Corporation. Installation Manual...
  • Page 15 A replacement fuse cover can be purchased from your local Panasonic dealer. IF THE FITTED MOULDED PLUG IS UNSUITABLE FOR THE AC OUTLET IN YOUR PREMISES, THEN THE FUSE SHOULD BE REMOVED AND THE PLUG CUT OFF AND DISPOSED OF SAFELY.
  • Page 16 How to replace the fuse: Open the fuse compartment with a screwdriver and replace the fuse and fuse cover. The equipment must be connected to direct extension lines, and a payphone should not be connected as an extension. 999 and 112 can be dialled on the apparatus after accessing the Exchange line for the purpose of making outgoing calls to the BT emergency services.
  • Page 17: Table Of Contents

    Attaching a Ferrite Core ....................68 3.2.10 Fastening an Amphenol Connector .................. 71 3.2.11 Wall Mounting (KX-TDE200) .................... 73 3.2.12 Wall Mounting (KX-TDE100) .................... 75 3.2.13 Floor Standing (KX-TDE200 Only) ................... 77 3.2.14 Surge Protector Installation ....................79 Information about the Main Processing Card .............. 82 3.3.1...
  • Page 18 3.5.4 CID8 Card (KX-TDA0193)....................93 3.5.5 E&M8 Card (KX-TDA0184) ....................94 3.5.6 T1 Card (KX-TDA0187).....................97 3.5.7 E1 Card (KX-TDA0188) ....................100 3.5.8 BRI4 Card (KX-TDA0284) and BRI8 Card (KX-TDA0288)..........103 3.5.9 PRI30 Card (KX-TDA0290CE/CJ) .................. 107 3.5.10 PRI23 Card (KX-TDA0290)..................... 111 3.5.11 IP-GW4E Card (KX-TDA0484)..................114 3.5.12 IP-GW16 Card (KX-TDA0490) ..................116 Information about the Physical Extension Cards ............118 3.6.1...
  • Page 19: Installation Manual

    3.12 Connection of Peripherals................... 216 3.12.1 Connection of Peripherals ....................216 3.13 LAN Connection ......................220 3.13.1 LAN Connection ......................220 3.14 Power Failure Connections ..................221 3.14.1 Power Failure Connections..................... 221 3.15 Starting the PBX ......................225 3.15.1 Starting the PBX......................225 Guide for the KX-TDE Maintenance Console ........227 Overview ........................
  • Page 20 Installation Manual...
  • Page 21: System Outline

    Section 1 System Outline This section provides general information on the PBX, including the system capacity and specifications. Installation Manual...
  • Page 22: System Highlights

    1.1 System Highlights System Highlights 1.1.1 System Highlights IPCMPR Card Features The IPCMPR card (the preinstalled Main Processing card) includes the following features and resources: VoIP Trunks/VoIP Extensions The IPCMPR card allows the use of IP trunks (H.323/SIP) and IP telephones (IP-PTs, IP softphones, and SIP Extensions).
  • Page 23 This PBX supports the connection of third party SIP supported IP telephones (hardphones and softphones). SIP Extensions make and receive calls using IP. IP Softphones This PBX supports the connection of Panasonic IP softphones, providing IP-PT operations and features using software on a PC. Internet Protocol (IP) Related Features...
  • Page 24 1.1 System Highlights External Device Support The following are just a few of the many useful optional devices available to enhance your telephony system: Portable Station (PS) Features PSs can be connected to this PBX. It is possible to use the PBX features using the PS like a PT. This PBX supports basic CSs (allows up to 4 PSs to be on a call simultaneously) as well as high-density CSs (allows up to 8 PSs to be on a call simultaneously).
  • Page 25 1.1 System Highlights Built-in Small Call Centre Features An incoming call distribution (ICD) group can be used as a small call centre with the following features: – Queuing Feature When a preprogrammed number of extensions in an ICD group are busy, additional incoming calls can wait in a queue.
  • Page 26: Basic System Construction

    The basic shelf contains an IPCMPR card for controlling the PBX. To use the system, install a power supply unit (PSU) in the PSU Slot and optional service cards in the basic shelf. KX-TDE100 KX-TDE200 Construction of the Basic Shelf...
  • Page 27: System Connection Diagram

    1.2 Basic System Construction 1.2.2 System Connection Diagram Private ITSP IP Network Network Trunk (Telephone Company Lines) Analogue/BRI/PRI/T1/E1 Remote PC Pure IP-PBX Router (e.g., ADSL Modem) Batteries IP-PT IP Softphone Fax Machine SIP Extension DSS Console Wireless Phone Printer CTI Server ISDN Telephone External Sensor/ DSS Console...
  • Page 28 1.2 Basic System Construction LCOT4 LCOT4 MSLC16 (KX-TDA0183) (KX-TDA0183) (KX-TDA0175) LCOT16 SLC16 (KX-TDA0181) (KX-TDA0174) Wireless Phone Fax Machine LCOT8 SLC8 (KX-TDA0180) (KX-TDA0173) CID/PAY8 (KX-TDA0189) EXT-CID (KX-TDA0168) CID8 KX-T7600 KX-T7600 KX-T7636/ (KX-TDA0193) Analogue KX-T7633 DLC16 Trunk (KX-TDA0172) DID8 Voice (KX-TDA0182) DLC8 Processing E &...
  • Page 29: Optional Equipment

    Power Supply Unit for the KX-TDE200. Total power output of 279 W. Safety Class 1 compliant. KX-TDA0104 M-Type Power Supply Unit (PSU-M) Power Supply Unit for the KX-TDE100 and KX- TDE200. Total power output of 140.4 W. Safety Class 1 compliant. KX-TDA0108 S-Type Power Supply Unit (PSU-S) Power Supply Unit for the KX-TDE100.
  • Page 30 1.3 Optional Equipment Model No. Model Name Description KX-TDA0172 16-Port Digital Extension Card 16-port digital extension card for DPTs, DSS (DLC16) consoles, and PT-interface CSs (Basic/High- density). KX-TDA0173 8-Port Single Line Telephone 8-port extension card for SLTs with 2 power failure Extension Card (SLC8) transfer (PFT) ports.
  • Page 31 NI (North American standard ISDN protocol) compliant. KX-TDA0470 16-Channel VoIP Extension Card (IP- 16-channel VoIP extension card. Compliant with EXT16) Panasonic proprietary protocol, and ITU-T G.729a and G.711 CODEC methods. KX-TDA0484 4-Channel VoIP Gateway Card (IP- 4-channel VoIP gateway card. Compliant with VoIP GW4E) H.323 V.2 protocol, and ITU-T G.729a, G.723.1 and...
  • Page 32: Specifications

    1.4 Specifications Specifications 1.4.1 General Description Control Bus Original bus (16-bit, 8 MHz, 10 megabytes per second) Communication Bus H.100 bus conformity (1024 time slots) Switching Non-blocking Power Input PSU-S 100 V AC to 130 V AC; 1.4 A/200 V AC to 240 V AC; 0.8 A; 50 Hz/60 Hz PSU-M 100 V AC to 130 V AC;...
  • Page 33 DSS Console and Add-on 1-pair wire (D1, D2) Key Module Dimension KX-TDE100 334 mm (W) × 390 mm (H) × 272 mm (D) KX-TDE200 430 mm (W) × 415 mm (H) × 276 mm (D) Weight (when fully KX-TDE100...
  • Page 34: Characteristics

    1.4 Specifications 1.4.2 Characteristics PT: KX-T7600 series DPT: 90 Ω; all other DPTs/APTs: 40 Ω Terminal Equipment Loop Limit • SLT: 600 Ω including set • Doorphone: 20 Ω • CS: 130 Ω; PT-interface CS (Basic/High-density): 65 Ω • 15 000 Ω minimum Minimum Leakage Resistance Maximum Number of Extension 1 for PT or SLT...
  • Page 35: System Capacity

    1.4 Specifications 1.4.3 System Capacity Type and Maximum Number of Slots The PBX supports the following type and number of slots. Slot Type Maximum Number KX-TDE100 KX-TDE200 IPCMPR Card Slot Free Slot Virtual Trunk Slot Virtual Slot Virtual Extension Slot...
  • Page 36 Any card that exceeds the capacity of the PBX will be ignored. • When the PBX starts up with an invalid configuration, some cards will be ignored. Cards Installed in Free Slots or Virtual Slots Maximum Number Card Type KX-TDE100 KX-TDE200 IPCMPR Trunk Card Virtual Trunk Card V-IPGW16...
  • Page 37 1.4 Specifications Cards Mounted on Other Optional Service Cards Maximum Number Card Type Mounted on KX-TDE100 KX-TDE200 DSP16 DSP64 IPCMPR Card CID/PAY8 LCOT8 Card/LCOT16 Card CID8 EXT-CID SLC8 Card DPH4 DPH2 ECHO16 OPB3 Card MSG4 EIO4 Only 1 ECHO16 card can be mounted on each OPB3 card.
  • Page 38 1.4 Specifications Maximum Terminal Equipment The following shows the number of each terminal equipment type supported by the PBX. Terminal Equipment Type KX-TDE100 KX-TDE200 Telephone KX-T7600 series DPT KX-T7560/KX-T7565 DPT Other DPT IP-PT IP-PT (supported by IP-EXT16 card) IP-PT (supported by IPCMPR...
  • Page 39 1.4 Specifications Note for KX-NT265 IP-PT users The supported card varies depending on the software version of your KX-NT265 IP-PT. To confirm the version, follow the procedure below: While starting up SP-PHONE SP-PHONE PROGRAM "AP Version". Select Select "Maintenance". "Version display". To exit the programming mode Software version SP-PHONE...
  • Page 40 1.4 Specifications PSU Capacity Each PSU supports a different load figure. PSU Type Maximum Load Figure PSU-S (for KX-TDE100 only) PSU-M PSU-L (for KX-TDE200 only) Calculation Example (KX-TDE200) Equipment Type Load Figure KX-T7600 series DPT 48 units Other DPT 2 units...
  • Page 41: Activation Key Installation

    Section 2 Activation Key Installation This section describes information on activation keys, including how to obtain an activation key and install it in the SD Memory Card. Installation Manual...
  • Page 42: Information About The Activation Keys

    2.1 Information about the Activation Keys Information about the Activation Keys 2.1.1 Activation Keys To use IP trunks and IP telephones on a private IP network using the IPCMPR card or to upgrade the software for enhanced features, you need the appropriate activation keys. Type and Maximum Number of Activation Keys The PBX supports the following type and number of activation keys: Maximum...
  • Page 43 2.1 Information about the Activation Keys Additional Activation Keys in the SD Memory Card (Activation Key Files) In addition to the preinstalled activation keys on the DSP16/DSP64 card, the following type and number of activation keys are installed in the SD Memory Card: Maximum Number Supported IP Trunks/IP Telephones Activation Key Type...
  • Page 44: Activation Key Card And Key Management System

    2.1 Information about the Activation Keys 2.1.2 Activation Key Card and Key Management System To obtain additional activation keys, you need to purchase the appropriate activation key cards and access the Key Management System. You can download the activation keys as an activation key file from the Key Management System.
  • Page 45: Activation Key File

    2.1 Information about the Activation Keys 2.1.3 Activation Key File The corresponding number of IP trunks and IP telephones or enhanced features can be activated by installing the downloaded activation key file(s) in the SD Memory Card of the IPCMPR card using the KX- TDE Maintenance Console.
  • Page 46 2.1 Information about the Activation Keys Installation Manual...
  • Page 47: Installation

    Section 3 Installation This section describes the procedures to install the PBX. Detailed instructions for planning the installation site, installing the shelves and optional service cards, and cabling of peripheral equipment are provided. Further information on system expansion and peripheral equipment installation is included.
  • Page 48: Before Installation

    Use caution when installing or modifying telephone lines. Installation Precautions This set is made for wall mounting (KX-TDE100/KX-TDE200) or floor standing (KX-TDE200 only), and should be installed in a location where it is accessible for inspections and maintenance. To prevent malfunction, noise, or discolouration, avoid installing the system in the following locations: In direct sunlight and hot, cold, or humid places.
  • Page 49 3.1 Before Installation Use 2-pair telephone cables when connecting PTs. Use 1-pair telephone cables when connecting SLTs, data terminals, answering machines, computers, Voice Processing Systems, etc. Unplug the system from its power source when wiring, and plug the system back in only after all wiring is completed.
  • Page 50: Installation Of The Pbx

    3.2 Installation of the PBX Installation of the PBX 3.2.1 Unpacking Unpack the box and check the items below: KX-TDE100 KX-TDE200 Main Unit Ferrite Core (for the IPCMPR card) AC Cord with a Ferrite Core Metal Bracket Screw A Screw B (Black)
  • Page 51: Names And Locations

    3.2 Installation of the PBX 3.2.2 Names and Locations Inside View KX-TDE100 KX-TDE200 RUN Indicator ALARM Indicator MNT Port LAN Port PSU Slot Null Slot (not available for any optional service card) Free Slots 1 to 6 (from the left)
  • Page 52: Opening/Closing The Front Cover

    3.2 Installation of the PBX 3.2.3 Opening/Closing the Front Cover Opening the Front Cover Insert a flathead screwdriver into the opening (on the left of the screw cover) and unlatch the screw cover. Screw Cover Turn the screw anticlockwise to loosen. Slide the front cover to the right until it stops, then lift the front cover.
  • Page 53 3.2 Installation of the PBX Closing the Front Cover Hook the front cover onto the shelf (line up the protrusions on the cover with the receptacles on the shelf). Then slide the front cover to the left until it locks. Turn the screw clockwise to tighten.
  • Page 54: Installing/Replacing The Power Supply Unit

    Lower/Upper Input Voltage Range Current Input Frequency PSU-S Lower: 100 V AC to 130 V AC 1.4 A (for KX-TDE100) Upper: 200 V AC to 240 V AC 0.8 A PSU-M Lower: 100 V AC to 130 V AC 2.5 A...
  • Page 55 3.2 Installation of the PBX Never install or replace a PSU unless at least 20 s has elapsed after the AC supply and backup battery supply are disconnected. To protect the back board from static electricity, do not touch parts on the back board in the main unit and PSU.
  • Page 56 3.2 Installation of the PBX Push the release lever in the direction of the arrow, so that the PSU engages securely with the connector on the back board. Back Board Release Lever Turn the 4 screws clockwise, in the order indicated by the numbers 1 to 4, to fix the PSU. Screws Replacing the Power Supply Unit Unplug the AC power cord and Back-up Battery Cable.
  • Page 57 3.2 Installation of the PBX Turn the 4 screws anticlockwise to loosen them. Screws Pull the release lever in the direction of the arrow to disconnect the PSU from the back board. Back Board Release Lever Replace the PSU. New PSU Current PSU Follow the steps in "Installing the Power Supply Unit".
  • Page 58: Frame Earth Connection

    3.2 Installation of the PBX 3.2.5 Frame Earth Connection IMPORTANT Connect the frame of the PBX to earth. Loosen the screw. Screw Insert an earthing wire (user- supplied)*. Tighten the screw. Connect the earthing wire to Earthing earth. wire To earth * For earthing wire, green-and-yellow insulation is required, and the cross-sectional area of the conductor must be more than 0.75 mm or 18 AWG.
  • Page 59: Backup Battery Connection

    3.2 Installation of the PBX 3.2.6 Backup Battery Connection The backup batteries and Back-up Battery Cable provide a backup power supply to allow full use of the PBX in the event of a power failure. In case of power failure, the backup batteries automatically maintain the power to the PBX without interruption.
  • Page 60 3.2 Installation of the PBX Connecting Backup Batteries Turn off the battery switch on the PSU. Connect the Back-up Battery Cable to a set of 3 identical batteries. Battery Switch Battery Connector Back-up Battery Cable Fuse Black Backup Batteries (VRLA 12 V DC x 3) Installation Manual...
  • Page 61: Installing/Removing The Optional Service Cards

    3.2 Installation of the PBX 3.2.7 Installing/Removing the Optional Service Cards CAUTION To protect the back board from static electricity, do not touch parts on the back board in the main unit and on the optional service cards. To discharge static electricity, touch ground or wear an earthing strap. Note The optional service cards can be installed or removed while the DC power is supplied.
  • Page 62 3.2 Installation of the PBX Holding the card as shown below, push the release lever in the direction of the arrow so that the card engages securely with the connector on the back board. Back Board Release Lever Turn the 2 screws clockwise to fix the card in place. Screws Note Make sure the screws are tightened to earth the card securely.
  • Page 63 3.2 Installation of the PBX Covering the Blank Slots Be sure to cover each slot in which no optional service card is installed by using a Blank Slot Cover. CAUTION Failure to install the Blank Slot Cover may cause electromagnetic interference. Installation Manual...
  • Page 64 3.2 Installation of the PBX Handling of the Cables When cables are connected to the PBX, run the cables to either the right or the left and then towards the back of the shelf as shown below. Note For safety reasons, do not stretch, bend, or pinch the AC power cord. Installation Manual...
  • Page 65 3.2 Installation of the PBX Removing the Optional Service Cards Turn the 2 screws anticlockwise to loosen them. Screws Pull the release lever in the direction of the arrow to disconnect the card from the back board. Pull the card from the shelf to remove it. Back Board Release Lever Installation Manual...
  • Page 66: Types Of Connectors

    3.2 Installation of the PBX 3.2.8 Types of Connectors Connector Type Pin Number Used for • DHLC8 (KX-TDA0170) RJ11 • SLC8 (KX-TDA0173) • SLC16 (KX-TDA0174) • MSLC16 (KX-TDA0175) • LCOT8 (KX-TDA0180) • LCOT16 (KX-TDA0181) • LCOT4 (KX-TDA0183) (Twisted pair cable) •...
  • Page 67 3.2 Installation of the PBX Connector Type Pin Number Used for • DPH4 (KX-TDA0161) 10-pin 8-pin • DPH2 (KX-TDA0162) Terminal Terminal Block Block • EIO4 (KX-TDA0164) • Basic Shelf RS-232C (Shielded cable) • IPCMPR Mini Plug Installation Manual...
  • Page 68: Attaching A Ferrite Core

    3.2 Installation of the PBX 3.2.9 Attaching a Ferrite Core A ferrite core must be attached when: • an RJ45 connector is connected to an IPCMPR, T1, E1, PRI, BRI, IP-GW16 or IP-EXT16 cards, or • an Amphenol connector is connected to an extension card. Note In Canada, the ferrite core is not necessarily required for the T1 and PRI23 cards.
  • Page 69 3.2 Installation of the PBX For a BRI Card Attach the ferrite core, then close the case of the ferrite core. Attach the ferrite core as close to the card's connector as possible. The ferrite core is included with the card. When only 1 or 2 cables are used for connection, wrap the cable(s) once around the ferrite core.
  • Page 70 3.2 Installation of the PBX Attaching to an Amphenol Connector For Extension Cards Pass the cable through the ferrite core, then close the case of the ferrite core. Attach the ferrite core 3 cm away from the connector. The ferrite core is included with the card. 3 cm If you need to open the ferrite core, use a flathead screwdriver to unlatch the case of the ferrite core.
  • Page 71: Fastening An Amphenol Connector

    3.2 Installation of the PBX 3.2.10 Fastening an Amphenol Connector An Amphenol 57JE-type connector is used on some of the optional service cards. To connect an Amphenol connector, use the spring latch or screw to fix the upper part and use Velcro tape ®...
  • Page 72 3.2 Installation of the PBX Amphenol Connector Pin Assignment Chart Below is an Amphenol connector pin assignment chart for all optional service cards that use the Amphenol connector. For more details, refer to the appropriate section in "3.5 Information about the Physical Trunk Cards"...
  • Page 73: Wall Mounting (Kx-Tde200)

    3.2 Installation of the PBX 3.2.11 Wall Mounting (KX-TDE200) WARNING • MAKE SURE THAT THE WALL THAT THE SHELF WILL BE ATTACHED TO IS STRONG ENOUGH TO SUPPORT THE SHELF. IF NOT, IT IS NECESSARY FOR THE WALL TO BE REINFORCED. •...
  • Page 74 3.2 Installation of the PBX Hook the shelf onto the metal bracket, making sure that the shelf slides down and onto the hooked parts of the metal bracket. Use 2 screws (B) to fix both sides of the shelf. Screw (B) Installation Manual...
  • Page 75: Wall Mounting (Kx-Tde100)

    3.2 Installation of the PBX 3.2.12 Wall Mounting (KX-TDE100) WARNING • MAKE SURE THAT THE WALL THAT THE SHELF WILL BE ATTACHED TO IS STRONG ENOUGH TO SUPPORT THE SHELF. IF NOT, IT IS NECESSARY FOR THE WALL TO BE REINFORCED.
  • Page 76 3.2 Installation of the PBX Hook the shelf onto the metal bracket, making sure that the shelf slides down and onto the hooked parts of the metal bracket. Use 2 screws (B) to fix both sides of the shelf. Screw (B) Installation Manual...
  • Page 77: Floor Standing (Kx-Tde200 Only)

    3.2 Installation of the PBX 3.2.13 Floor Standing (KX-TDE200 Only) Notes • Do not block the openings of the shelf. Allow space of at least 20 cm above and 10 cm at the sides of the shelf. • Make sure that the surface behind the shelf is flat and free of obstacles, so that the openings on the back of the shelf will not be blocked.
  • Page 78 3.2 Installation of the PBX Lift the shelf, attach it to the metal bracket, slide it backwards until it locks, and retain it with 2 screws (B). FRONT Screws (B) Metal Bracket Fix the front cover on the shelf (refer to "3.2.3 Opening/Closing the Front Cover"). Installation Manual...
  • Page 79: Surge Protector Installation

    3.2 Installation of the PBX 3.2.14 Surge Protector Installation Overview A massive electrical surge can be caused if lightning strikes a telephone cable 10 m above ground, or if a telephone line comes into contact with a power line. A surge protector is a device that is connected to a trunk to prevent potentially dangerous electrical surges from entering the building via the trunk and damaging the PBX and connected equipment.
  • Page 80 3.2 Installation of the PBX Outside Installation (Main Building) Surge Protector Trunk (Another Building) Trunk Extn. PT-interface CS Terminal Board Surge Extn. Protector Extn. Extn. PT-interface CS Earth Extn.: Extension Line If you install an extension outside of the building, the following precautions are recommended: Install the extension wire underground.
  • Page 81 3.2 Installation of the PBX Connect the earth rod to the surge protector using an earthing wire with a cross-sectional area of at least 1.3 mm Bury the earth rod near the protector. The earthing wire should be as short as possible. The earthing wire should run straight to the earth rod.
  • Page 82: Information About The Main Processing Card

    3.3 Information about the Main Processing Card Information about the Main Processing Card 3.3.1 IPCMPR Card Function The IPCMPR card is the preinstalled main processing card with built-in SVM feature (2-channel). The Virtual Cards (trunk/extension) can be installed in Virtual Slots of the IPCMPR card and can be activated with the activation keys.
  • Page 83 3.3 Information about the Main Processing Card Notes • Make sure to use the MNT port for PC connection, and the LAN port for LAN connection. • The maximum length of the cable to be connected to the IPCMPR card is 100 m. •...
  • Page 84 3.3 Information about the Main Processing Card LED Indications Indication Colour Description BATT ALARM Battery alarm indication • OFF: Normal ON: Alarm SD ACCESS Green SD memory card status • ON: Accessing 10BASE-T/100BASE-TX MNT 2 LINK Green Link status indication •...
  • Page 85: Dsp16 Card (Kx-Tde0110) And Dsp64 Card (Kx-Tde0111)

    3.3 Information about the Main Processing Card 3.3.2 DSP16 Card (KX-TDE0110) and DSP64 Card (KX-TDE0111) Function DSP16: 16-channel digital signal processor card with a 4-Channel IP Trunk activation key and a 8- Channel IP Proprietary Telephone activation key preinstalled. Compliant with ITU-T G.729a and G.711 CODEC methods.
  • Page 86: Rmt Card (Kx-Tda0196)

    3.3 Information about the Main Processing Card 3.3.3 RMT Card (KX-TDA0196) Function Analogue modem card for remote communication with the PBX. ITU-T V.90 support. To be mounted on the IPCMPR card. IPCMPR Card inside RMT Card Screw Accessories and User-supplied Items Accessories (included): Screws ×...
  • Page 87: Information About The Virtual Cards

    3261, 3262, 3264, 3311, 3581, 3960 and 4028 protocols, and ITU-T G.729a/b and G.711 CODEC methods. Virtual 32-Channel VoIP Extension Card Virtual Card for 32 VoIP extensions. Compliant with Panasonic (V-IPEXT32) proprietary protocol, and ITU-T G.729a, G.711 and G.722 CODEC methods.
  • Page 88: Information About The Physical Trunk Cards

    3.5 Information about the Physical Trunk Cards Information about the Physical Trunk Cards 3.5.1 LCOT4 Card (KX-TDA0183), LCOT8 Card (KX-TDA0180), and LCOT16 Card (KX-TDA0181) Function LCOT4: 4-port analogue trunk card with 2 power failure transfer (PFT) ports. LCOT8: 8-port analogue trunk card with 2 power failure transfer (PFT) ports. One CID8 or CID/PAY8 card can be mounted on the LCOT8 card (refer to "3.5.3 CID/PAY8 Card (KX-TDA0189)"...
  • Page 89 3.5 Information about the Physical Trunk Cards Pin Assignments Amphenol Connector Signal Name Function Signal Name Function Ring port 1 Tip port 1 Ring port 2 Tip port 2 Ring port 3 Tip port 3 Ring port 4 Tip port 4 Ring port 5 Tip port 5 Ring port 6...
  • Page 90: Did8 Card (Kx-Tda0182)

    3.5 Information about the Physical Trunk Cards 3.5.2 DID8 Card (KX-TDA0182) Function 8-port DID trunk card. Amphenol To DID line Accessories and User-supplied Items Accessories (included): Screws × 2 User-supplied (not included): Amphenol connector Notes • To connect the Amphenol connector, refer to "3.2.10 Fastening an Amphenol Connector". •...
  • Page 91 3.5 Information about the Physical Trunk Cards LED Indications Indication Colour Description CARD STATUS Green/Red Card status indication • OFF: Power Off • Green ON: Normal (all ports are idle) • Green Flashing (60 times per minute): Normal (a port is in use) •...
  • Page 92: Cid/Pay8 Card (Kx-Tda0189)

    3.5 Information about the Physical Trunk Cards 3.5.3 CID/PAY8 Card (KX-TDA0189) Function 8-port Caller ID signal type FSK/FSK (with Call Waiting Caller ID [Visual Caller ID])/DTMF, and 8-port Pay Tone Service (12 kHz/16 kHz). To be mounted on the LCOT8/LCOT16 cards. Set all DIP switches for ports 09-16 at "OFF"...
  • Page 93: Cid8 Card (Kx-Tda0193)

    3.5 Information about the Physical Trunk Cards 3.5.4 CID8 Card (KX-TDA0193) Function 8-port Caller ID signal type FSK/FSK (with Call Waiting Caller ID [Visual Caller ID])/DTMF. To be mounted on the LCOT8/LCOT16 cards. LCOT16 card only inside CID8 Card Screw S W 1 Accessories and User-supplied Items Accessories (included): Screws ×...
  • Page 94: E&M8 Card (Kx-Tda0184)

    3.5 Information about the Physical Trunk Cards 3.5.5 E&M8 Card (KX-TDA0184) Function 8-port E & M (TIE) trunk card. Type 5 support. Amphenol To terminal board from the E & M (TIE) line Accessories and User-supplied Items Accessories (included): Screws × 2 User-supplied (not included): Amphenol connector Notes •...
  • Page 95 3.5 Information about the Physical Trunk Cards Pin Assignments Amphenol Connector Signal Name Function Signal Name Function Tip port 1 Ring port 1 Tip 1 port 1 Ring 1 port 1 E line port 1 M line port 1 SG line port 1 SG line port 2 Tip port 2 Ring port 2...
  • Page 96 3.5 Information about the Physical Trunk Cards LED Indications Indication Colour Description CARD STATUS Green/Red Card status indication • OFF: Power Off • Green ON: Normal (all ports are idle) • Green Flashing (60 times per minute): Normal (a port is in use) •...
  • Page 97: T1 Card (Kx-Tda0187)

    3.5 Information about the Physical Trunk Cards 3.5.6 T1 Card (KX-TDA0187) Function 1-port T1 trunk card. EIA/TIA standard compliant. LEDs RJ45 To NT1 / Extension Accessories and User-supplied Items Accessories (included): Ferrite core × 1 User-supplied (not included): RJ45 connector Notes •...
  • Page 98 3.5 Information about the Physical Trunk Cards Pin Assignments RJ45 Connector for Trunk Use Signal Name Level [V] Function Receive data (+) Receive data (-) Reserved – – Transmit data (-) Transmit data (+) Reserved – – RJ45 Connector for Extension Use Signal Name Level [V] Function...
  • Page 99 3.5 Information about the Physical Trunk Cards Indication Colour Description SYNC Green Synchronisation status indication • OFF: Not synchronised • ON: Synchronised • Flashing (60 times per minute): Synchronised (Clock Master) Maximum Cabling Distance of Extension Connection The maximum length of the extension cable that connects the T1 cards is shown below: Diameter Maximum Distance 0.5 mm:...
  • Page 100: E1 Card (Kx-Tda0188)

    3.5 Information about the Physical Trunk Cards 3.5.7 E1 Card (KX-TDA0188) Function 1-port E1 trunk card. ITU-T standard compliant. LEDs RJ45 BNC (TX) outer conductor J 3 0 8 J 3 0 8 To NT1/Extension For Frame For Frame To NT1/Extension Ground Open Ground Short For RJ45...
  • Page 101 3.5 Information about the Physical Trunk Cards Switch Settings Switch Type Usage and Status Definition Select 120 Ω (default) or 75 Ω to match the connector type to be Termination Slide used. Slide When using an RJ45 connector, select A (default) for trunk or B for extension use.
  • Page 102 3.5 Information about the Physical Trunk Cards BNC (coaxial) Connector (RX) Signal Name Level [V] Function Receive data (-) Receive data (+) LED Indications Indication Colour Description CARD STATUS Green/Red Card status indication • OFF: Power Off • Green ON: Normal (all ports are idle) •...
  • Page 103: Bri4 Card (Kx-Tda0284) And Bri8 Card (Kx-Tda0288)

    3.5 Information about the Physical Trunk Cards 3.5.8 BRI4 Card (KX-TDA0284) and BRI8 Card (KX-TDA0288) Function BRI4: 4-port ISDN Basic Rate Interface card with 1 power failure transfer port. EURO-ISDN/ETSI compliant. BRI8: 8-port ISDN Basic Rate Interface card with 1 power failure transfer port. EURO-ISDN/ETSI compliant.
  • Page 104 3.5 Information about the Physical Trunk Cards Switch Settings Switch Type Usage and Status Definition Slide Select A (default) for trunk or B for extension use. Pin Assignments RJ45 Connector for Trunk Use Signal Name Level [V] Function Reserved – –...
  • Page 105 3.5 Information about the Physical Trunk Cards Indication Colour Description LINE 8 Green Line status indication (LINE 1 to LINE 8): LINE 7 Refer to "LINE LED Pattern" below for details. LINE 6 Note LINE 5 LINE 4 LINE 5 to LINE 8 are for BRI8 card only. LINE 3 LINE 2 LINE 1...
  • Page 106 3.5 Information about the Physical Trunk Cards Maximum Cabling Distance of S0 Bus Connection The maximum length of the extension cable that connects the PBX and the ISDN terminal equipment (TE) is shown below: CAT 5: Under 1000 m Point-to-Point CAT 5: Under 150 m Point-to-Multipoint TE 1...
  • Page 107: Pri30 Card (Kx-Tda0290Ce/Cj)

    3.5 Information about the Physical Trunk Cards 3.5.9 PRI30 Card (KX-TDA0290CE/CJ) Function 1-port ISDN Primary Rate Interface card (30B channels). EURO-ISDN/ETSI compliant. LEDs RJ45 To NT1 / Extension To NT1/Extension For RJ45 BNC (TX) BNC (RX) 120Ω 120Ω For BNC 75Ω...
  • Page 108 3.5 Information about the Physical Trunk Cards Switch Settings Switch Type Usage and Status Definition Select 120 Ω (default) or 75 Ω to match the connector type to be Termination Slide used. Slide When using an RJ45 connector, select A (default) for trunk or B for extension use.
  • Page 109 3.5 Information about the Physical Trunk Cards BNC (coaxial) Connector (RX) Signal Name Level [V] Function Receive data (-) Receive data (+) LED Indications Indication Colour Description CARD STATUS Green/Red Card status indication • OFF: Power Off • Green ON: Normal (all ports are idle) •...
  • Page 110 3.5 Information about the Physical Trunk Cards Maximum Cabling Distance of Extension Connection The maximum length of the extension cable that connects the PRI30 cards is shown below: Diameter Maximum Distance 0.5 mm: 200 m Installation Manual...
  • Page 111: Pri23 Card (Kx-Tda0290)

    3.5 Information about the Physical Trunk Cards 3.5.10 PRI23 Card (KX-TDA0290) Function 1-port ISDN Primary Rate Interface card (23B channels). NI (North American standard ISDN protocol) compliant. LEDs RJ45 To NT1/ Extension Accessories and User-supplied Items Accessories (included): Ferrite core × 1 User-supplied (not included): RJ45 connector Notes •...
  • Page 112 3.5 Information about the Physical Trunk Cards Pin Assignments RJ45 Connector for Trunk Use Signal Name Level [V] Function Receive data (+) Receive data (-) Reserved – – Transmit data (-) Transmit data (+) Reserved – – RJ45 Connector for Extension Use Signal Name Level [V] Function...
  • Page 113 3.5 Information about the Physical Trunk Cards Indication Colour Description SYNC Green Synchronisation status indication • OFF: Not synchronised • ON: Synchronised • Flashing (60 times per minute): Synchronised (Clock Master) D-LINK Green Data link status indication • OFF: Not established •...
  • Page 114: Ip-Gw4E Card (Kx-Tda0484)

    3.5 Information about the Physical Trunk Cards 3.5.11 IP-GW4E Card (KX-TDA0484) Function 4-channel VoIP gateway card. Compliant with VoIP H.323 V.2 protocol, and ITU-T G.729a, G.723.1 and G.711 CODEC methods. LEDs RJ45 (10BASE-T/100BASE-TX) To private IP network Accessories and User-supplied Items Accessories (included): CD-ROM (including documentation for web programming) ×...
  • Page 115 3.5 Information about the Physical Trunk Cards LED Indications Indication Colour Description CARD STATUS Green/Red Card status indication • OFF: Power Off • Green ON: Normal (all ports are idle) • Green Flashing (60 times per minute): Normal (a port is in use) •...
  • Page 116: Ip-Gw16 Card (Kx-Tda0490)

    3.5 Information about the Physical Trunk Cards 3.5.12 IP-GW16 Card (KX-TDA0490) Function 16-channel VoIP gateway card. Compliant with VoIP H.323 V.2 protocol, and ITU-T G.729a, G.723.1 and G.711 CODEC methods. LEDs RJ45 (10BASE-T/100BASE-TX Full Duplex) To private IP network Accessories and User-supplied Items Accessories (included): Ferrite core ×...
  • Page 117 3.5 Information about the Physical Trunk Cards LED Indications Indication Colour Description CARD STATUS Green/Red Card status indication • OFF: Power Off • Green ON: Normal (all ports are idle) • Green Flashing (60 times per minute): Normal (a port is in use) •...
  • Page 118: Information About The Physical Extension Cards

    3.6 Information about the Physical Extension Cards Information about the Physical Extension Cards 3.6.1 CSIF4 Card (KX-TDA0143) and CSIF8 Card (KX-TDA0144) Function CSIF4: 4-port CS interface card for 4 CSs. CSIF8: 8-port CS interface card for 8 CSs. RJ45 (LINE 1 to LINE 8) To CS Accessories and User-supplied Items Accessories (included): none...
  • Page 119 3.6 Information about the Physical Extension Cards Pin Assignments RJ45 Connector Signal Name Function Reserved – Data port (High) POWH Power (High) POWL Power (Low) Data port (Low) Reserved – LED Indications Indication Colour Description CARD STATUS Green/Red Card status indication •...
  • Page 120: Dhlc8 Card (Kx-Tda0170)

    3.6 Information about the Physical Extension Cards 3.6.2 DHLC8 Card (KX-TDA0170) Function 8-port digital hybrid extension card for DPTs, APTs, SLTs, DSS consoles, and PT-interface CSs (Basic/High- density), with 2 power failure transfer (PFT) ports. Amphenol To extensions Accessories and User-supplied Items Accessories (included): Screws ×...
  • Page 121 3.6 Information about the Physical Extension Cards Pin Assignments Amphenol Connector No. Signal Name Function No. Signal Name Function SLT Ring port 1 SLT Tip port 1 PT Data port 1 (Low) PT Data port 1 (High) Reserved – Reserved –...
  • Page 122 3.6 Information about the Physical Extension Cards LED Indications Indication Colour Description CARD STATUS Green/ Card status indication Orange/Red • OFF: Power Off • Green ON: Normal (all ports are idle) • Green Flashing (60 times per minute): Normal (a port is in use) •...
  • Page 123: Dlc8 Card (Kx-Tda0171)

    3.6 Information about the Physical Extension Cards 3.6.3 DLC8 Card (KX-TDA0171) Function 8-port digital extension card for DPTs, DSS consoles, and PT-interface CSs (Basic/High-density). Amphenol To extensions Accessories and User-supplied Items Accessories (included): Screws × 2, Ferrite core × 1 User-supplied (not included): Amphenol connector Notes •...
  • Page 124 3.6 Information about the Physical Extension Cards Pin Assignments Amphenol Connector Signal Name Function Signal Name Function Reserved – Reserved – Data port 1 (Low) Data port 1 (High) Reserved – 28-29 Reserved – Data port 2 (Low) Data port 2 (High) Reserved –...
  • Page 125: Dlc16 Card (Kx-Tda0172)

    3.6 Information about the Physical Extension Cards 3.6.4 DLC16 Card (KX-TDA0172) Function 16-port digital extension card for DPTs, DSS consoles, and PT-interface CSs (Basic/High-density). Amphenol To extensions Accessories and User-supplied Items Accessories (included): Screws × 2, Ferrite core × 1 User-supplied (not included): Amphenol connector Notes •...
  • Page 126 3.6 Information about the Physical Extension Cards Pin Assignments Amphenol Connector Signal Name Function Signal Name Function Data port 1 (Low) Data port 1 (High) Data port 2 (Low) Data port 2 (High) Data port 3 (Low) Data port 3 (High) Data port 4 (Low) Data port 4 (High) Data port 5 (Low)
  • Page 127: Slc8 Card (Kx-Tda0173)

    3.6 Information about the Physical Extension Cards 3.6.5 SLC8 Card (KX-TDA0173) Function 8-port extension card for SLTs with 2 power failure transfer (PFT) ports. Amphenol To extensions Accessories and User-supplied Items Accessories (included): Screws × 2, Ferrite core × 1 User-supplied (not included): Amphenol connector Notes •...
  • Page 128 3.6 Information about the Physical Extension Cards Pin Assignments Amphenol Connector Signal Name Function Signal Name Function Ring port 1 Tip port 1 Reserved – 27-28 Reserved – Ring port 2 Tip port 2 Reserved – 30-31 Reserved – Ring port 3 Tip port 3 Reserved –...
  • Page 129: Ext-Cid Card (Kx-Tda0168)

    3.6 Information about the Physical Extension Cards 3.6.6 EXT-CID Card (KX-TDA0168) Function Sends Caller ID signals to extension ports. To be mounted on the SLC8 card only. inside SLC8 Card Screw EXT-CID Card Accessories and User-supplied Items Accessories (included): Screws × 2 User-supplied (not included): none Installation Manual...
  • Page 130: Slc16 Card (Kx-Tda0174) And Mslc16 Card (Kx-Tda0175)

    Accessories (included): Screws × 2, Ferrite core × 1 User-supplied (not included): Amphenol connector Notes • Panasonic SLT with Message Waiting Lamp (e.g., KX-T7310) is recommended for connection to the MSLC16 card. • Attach the included ferrite core to the cable. Refer to "3.2.9 Attaching a Ferrite Core".
  • Page 131 3.6 Information about the Physical Extension Cards Pin Assignments Amphenol Connector Signal Name Function Signal Name Function Ring port 1 Tip port 1 Ring port 2 Tip port 2 Ring port 3 Tip port 3 Ring port 4 Tip port 4 Ring port 5 Tip port 5 Ring port 6...
  • Page 132: Ip-Ext16 Card (Kx-Tda0470)

    3.6 Information about the Physical Extension Cards 3.6.8 IP-EXT16 Card (KX-TDA0470) Function 16-channel VoIP extension card. Compliant with Panasonic proprietary protocol, and ITU-T G.729a and G.711 CODEC methods. LEDs RJ45 (10BASE-T/100BASE-TX Full Duplex) To LAN Accessories and User-supplied Items Accessories (included): Ferrite core × 1...
  • Page 133 If the LINK indicator is OFF, the ONLINE indicator will also be OFF. ALARM Alarm indication • OFF: Normal • ON: Alarm VoIP BUSY Green Panasonic proprietary VoIP protocol process indication • OFF: VoIP process inactive • ON: VoIP process active LINK Green Link status indication • OFF: Connection error •...
  • Page 134: Information About The Other Physical Cards

    3.7 Information about the Other Physical Cards Information about the Other Physical Cards 3.7.1 OPB3 Card (KX-TDA0190) Function Optional 3-slot base card for mounting a maximum of 3 option cards from the following: • DPH4 card • DPH2 card • EIO4 card •...
  • Page 135: Dph4 Card (Kx-Tda0161)

    3.7 Information about the Other Physical Cards 3.7.2 DPH4 Card (KX-TDA0161) Function 4-port doorphone card for 4 doorphones and 4 door openers. To be mounted on the OPB3 card. Fully insert the connectors through the panel openings. DPH4 Card OPB3 Card 8-pin Screw 10-pin...
  • Page 136 3.7 Information about the Other Physical Cards Pin Assignments 8-pin Terminal Block Signal Name Function Doorphone 4 transmit com4 Doorphone 4 receive Doorphone 3 transmit com3 Doorphone 3 receive Doorphone 2 transmit com2 Doorphone 2 receive Doorphone 1 transmit com1 Doorphone 1 receive 10-pin Terminal Block Signal Name...
  • Page 137: Dph2 Card (Kx-Tda0162)

    3.7 Information about the Other Physical Cards 3.7.3 DPH2 Card (KX-TDA0162) Function 2-port doorphone card for 2 German-type doorphones and 2 door openers. To be mounted on the OPB3 card. Fully insert the connectors through the panel openings. DPH2 Card OPB3 Card 8-pin Screw...
  • Page 138 3.7 Information about the Other Physical Cards Pin Assignments 8-pin Terminal Block Signal Name Function Path_2b Doorphone 2 transmit Path_2a Doorphone 2 receive Call_2b Doorphone 2 call button Call_2a Doorphone 2 call button com Path_1b Doorphone 1 transmit Path_1a Doorphone 1 receive Call_1b Doorphone 1 call button Call_1a...
  • Page 139 3.7 Information about the Other Physical Cards Connection Diagram for German-type Doorphones and Door Openers German-type Doorphone 2 BL: Light RT: Call Button OP: Door Opener Connection Terminal Door Opener 2 DC: Doorphone Current Supply Control Terminal Path: Doorphone Call Path Call_2b L O U B Call_2a...
  • Page 140: Eio4 Card (Kx-Tda0164)

    3.7 Information about the Other Physical Cards 3.7.4 EIO4 Card (KX-TDA0164) Function 4-port external input/output card. To be mounted on the OPB3 card. Fully insert the connectors through the panel openings. EIO4 Card OPB3 Card 8-pin Screw 10-pin Accessories and User-supplied Items Accessories (included): Screws ×...
  • Page 141 3.7 Information about the Other Physical Cards Pin Assignments 8-pin Terminal Block Signal Name Function Control 4 Control 4 com Control 3 Control 3 com Control 2 Control 2 com Control 1 Control 1 com 10-pin Terminal Block Signal Name Function Reserved –...
  • Page 142 3.7 Information about the Other Physical Cards External Sensor Power to the external sensor is provided from the EIO4 card and must be grounded through the EIO4 card as indicated in the diagram below. A pair of "sensor" and "common" lines are connected to the EIO4 card for each external sensor.
  • Page 143: Echo16 Card (Kx-Tda0166)

    3.7 Information about the Other Physical Cards 3.7.5 ECHO16 Card (KX-TDA0166) Function 16-channel card for echo cancellation during conferences. To be mounted on the OPB3 card. OPB3 Card inside ECHO16 Card Screw Accessories and User-supplied Items Accessories (included): Screws × 3 User-supplied (not included): none Note To establish a conference call involving 6 to 8 parties, install an ECHO16 card and enable echo...
  • Page 144: Msg4 Card (Kx-Tda0191)

    3.7 Information about the Other Physical Cards 3.7.6 MSG4 Card (KX-TDA0191) Function 4-channel message card. To be mounted on the OPB3 card. OPB3 Card inside MSG4 Card Screw Accessories and User-supplied Items Accessories (included): Screws × 3 User-supplied (not included): none Installation Manual...
  • Page 145: Connection Of Extensions

    3.8 Connection of Extensions Connection of Extensions 3.8.1 Maximum Cabling Distances of the Extension Wiring (Twisted Cable) Cable Maximum Distance PT-interface CS ø 0.4 mm: 222 m (Basic/High-density) ø 0.5 mm: 347 m ø 0.6 mm: 500 m CAT 5: 347 m Cable Maximum Distance...
  • Page 146: Parallel Connection Of The Extensions

    3.8 Connection of Extensions 3.8.2 Parallel Connection of the Extensions Any SLT can be connected in parallel with an APT or a DPT as follows. Note In addition to an SLT, an answering machine, a fax machine or a modem (PC) can be connected in parallel with an APT or a DPT.
  • Page 147 3.8 Connection of Extensions Using an EXtra Device Port With KX-T7600 Series DPT (except KX-T7665) To DHLC8 card 2-conductor wiring cord 4-conductor wiring cord Connect pins "T" and "R". Connect pins "T", "R", "D1" and "D2". TO MAIN UNIT TO TEL / PABX To DHLC8 card To SLT...
  • Page 148: Digital Extra Device Port (Digital Xdp) Connection

    3.8 Connection of Extensions 3.8.3 Digital EXtra Device Port (Digital XDP) Connection A DPT can be connected to another DPT on the Digital XDP connection. In addition, if the DPT is connected to a DHLC8 card, it can also have an SLT connected in Parallel mode or XDP mode. Notes •...
  • Page 149 3.8 Connection of Extensions Using an EXtra Device Port To DLC8/DLC16 card 4-conductor wiring cord To DHLC8 card Connect pins "T", "R", 2-conductor wiring cord (for connection of SLT) "D1" and "D2". Connect pins "T" and "R". 4-conductor wiring cord Connect pins "T", "R", "D1"...
  • Page 150 3.8 Connection of Extensions With KX-T7600E Series DPT Using a Modular T-Adaptor To DLC8/DLC16 card Modular To DHLC8 card T-Adaptor (for connection of SLT) 2-conductor wiring cord Connect pins "T" and "R". 4-conductor wiring cord Connect pins "D1" and "D2". 4-conductor wiring cord Connect pins "D1"...
  • Page 151 3.8 Connection of Extensions Using an EXtra Device Port Connecting to a Slave DPT To DLC8/DLC16 card To DHLC8 card 4-conductor wiring cord (for connection of SLT) Connect pins "T", "R", 2-conductor wiring cord "D1" and "D2". Connect pins "T" and "R". 4-conductor wiring cord Connect pins "T", "R", "D1"...
  • Page 152 3.8 Connection of Extensions Connecting to a Master DPT To DLC8/DLC16 card To DHLC8 card 4-conductor wiring cord (for connection of SLT) Connect pins "D1" and "D2". 4-conductor wiring cord Connect pins "T", "R", "D1" and "D2". Master DPT Slave DPT 2-conductor wiring cord Connect pins "T"...
  • Page 153: First Party Call Control Cti Connection

    3.8 Connection of Extensions 3.8.4 First Party Call Control CTI Connection CTI connection between a PC and a KX-T7633/KX-T7636 DPT provides first party call control. The CTI connection is made via a USB interface (version 2.0), and uses the TAPI 2.1 protocol. A USB Module (KX-T7601) must be connected to the KX-T7633/KX-T7636 DPT.
  • Page 154: Connection Of Dect Portable Stations

    • KX-TD7580 Note for users in Europe The Cell Station Units for DECT are for connection to Panasonic PBXs in European countries only. Note For more details about the PS, refer to the Operating Instructions of the PS. RF Specification...
  • Page 155 3.9 Connection of DECT Portable Stations CAUTION • The CS should be kept free of dust, moisture, high temperature (more than 40 ), low temperature ˚C (less than 0 ), and vibration, and should not be exposed to direct sunlight. ˚C •...
  • Page 156: Procedure Overview

    3.9 Connection of DECT Portable Stations 3.9.2 Procedure Overview When connecting the wireless system, use extreme care in conducting the site survey. Site surveys can be conducted using the KX-TCA255/KX-TCA256/KX-TCA355/KX-TD7590 PS. An incorrectly performed site survey can result in poor service area, frequent noise, and disconnection of calls. 1.
  • Page 157 3.9 Connection of DECT Portable Stations Make sure that the radio signal strength level is greater than "3" at any location within the service area required by the user. 4. Finish the site survey Refer to "3.9.6 After Site Survey". Return all DIP switches of each CS to the OFF position, and stop supplying power.
  • Page 158: Site Planning

    3.9 Connection of DECT Portable Stations 3.9.3 Site Planning Choosing the best site for the CS requires careful planning and testing of essential areas. The best location may not always be convenient for installation. Read the following information before installing the unit. Understanding Radio Waves Characteristics of Radio Waves The transmission of radio waves and the CS coverage area depend on the structure and materials of the...
  • Page 159 3.9 Connection of DECT Portable Stations Object Material Transmission Tendency Wall Concrete The thicker they are, the less radio waves penetrate them. Ferroconcrete Radio waves can penetrate them, but the more iron there is, the more radio waves are reflected. Window Glass Radio waves usually penetrate them.
  • Page 160 3.9 Connection of DECT Portable Stations CS Coverage Area The example below shows the size of the coverage area of 1 CS if it is installed in an area with no obstacles. Note Radio signal strength levels are measured during the site survey (refer to "3.9.5 Site Survey Using the KX-TCA255/KX-TCA256/KX-TCA355/KX-TD7590").
  • Page 161 3.9 Connection of DECT Portable Stations Where CS coverage areas overlap, the PS will start call handover to the next CS if the signal from one CS becomes weak. However, if a PS moves away from a CS and there are no CSs available for handover, the PS may go out of range and the call could be lost.
  • Page 162: Before Site Survey

    3.9 Connection of DECT Portable Stations 3.9.4 Before Site Survey Use the KX-TCA255/KX-TCA256/KX-TCA355/KX-TD7590 PS to conduct the site survey. Note Display prompts for the site survey are only available in English. Checking the CS ID Number Check the CS ID number label attached to the CS. If the CS ID number label is not attached to the CS, check the CS ID number using the KX-TDE Maintenance Console.
  • Page 163 3.9 Connection of DECT Portable Stations Using the KX-TD7590 To enter letters INT' CS No. CS ID No. Press 1, 9, and POWER 0 to 7 0 to 9 and A to F for more than 5 seconds. To the Desired CS No. To the initial display Note To clear the CS ID number assigned to the PS, follow the procedure below:...
  • Page 164 3.9 Connection of DECT Portable Stations Setting and Installing the CS Temporarily for Site Survey Switch the Radio Signal Test switch from OFF to ON. Set the channel number switches as desired. Set the Power Supply Select switch as desired (KX-TDA0158CE only). KX-TDA0158CE Radio Signal Test Switch Power Supply Select Switch...
  • Page 165 3.9 Connection of DECT Portable Stations KX-TDA0141CE/KX-TDA0142CE DIP Switch Channel Number Switch Keep this switch at the default "OFF" position. Otherwise, the CS will not function. Radio Signal Test Switch Channel 0 Channel 1 Channel 2 Channel 3 Channel 4 Channel 5 Channel 6 Channel 7 Channel 8 Channel 9 Note If more than 1 CS is in Radio Signal Test mode, each CS must have a unique channel number.
  • Page 166 3.9 Connection of DECT Portable Stations After setting the DIP switch, connect the CS to an AC adaptor/battery box using a power supply adaptor, or connect to a CSIF/DLC/DHLC card. Notes • The AC adaptor should be connected to a vertically oriented or floor-mounted AC outlet. Do not connect the AC adaptor to a ceiling-mounted AC outlet, as the weight of the adaptor may cause it to become disconnected.
  • Page 167: Site Survey Using The Kx-Tca255/Kx-Tca256/Kx-Tca355/Kx-Td7590

    3.9 Connection of DECT Portable Stations 3.9.5 Site Survey Using the KX-TCA255/KX-TCA256/KX-TCA355/ KX-TD7590 The PS has a Radio Signal Test mode that monitors the state of the radio link to the CS for site survey. In Radio Signal Test mode, the frame loss and signal strength of a synchronous slot, and the signal strength of the other slots can be measured when the PS is monitoring the CS.
  • Page 168 3.9 Connection of DECT Portable Stations Measure the radio signal strength by moving towards and away from the CS. Move to the CS until the radio signal strength level becomes "12". Move away from the CS and identify the CS coverage area within which the radio signal strength level is greater than "8".
  • Page 169 3.9 Connection of DECT Portable Stations Repeat steps 1 and 2 for other CSs, and relocate the CSs when necessary. Overlap adjacent CS coverage areas where the radio signal strength level is "8" by 5 m to 10 m. Channel no. 0 Channel no.
  • Page 170 3.9 Connection of DECT Portable Stations Referring to the Stored Scan Data Using the KX-TCA255/KX-TCA256/KX-TCA355 Log No. Press 1, 9, and POWER 0 to 9 for more than 2 seconds. To go to other slots To go to specific channel Channel No.
  • Page 171: After Site Survey

    3.9 Connection of DECT Portable Stations 3.9.6 After Site Survey After obtaining the proper measurement results, exit Radio Signal Test mode before connecting the CS to the PBX. Keep pressing the POWER button on the PS until the PS is turned OFF. Disconnect the CS from the AC adaptor/battery box or the CSIF/DLC/DHLC card, and stop supplying electricity.
  • Page 172: Connecting A Cell Station To The Pbx

    3.9 Connection of DECT Portable Stations 3.9.7 Connecting a Cell Station to the PBX Using a CSIF Card Refer to the following example to connect a CS to the PBX. KX-TDA0142CE CSIF8 Card Port 1 Cable Maximum Distance ø 0.4 mm: 444 m ø...
  • Page 173 3.9 Connection of DECT Portable Stations Using a DHLC/DLC Card Refer to the following examples to connect a CS to the PBX. KX-TDA0158CE DHLC8 Card Cable Maximum Distance ø 0.4 mm: 222 m ø 0.5 mm: 347 m ø 0.6 mm: 500 m CAT 5: 347 m...
  • Page 174 3.9 Connection of DECT Portable Stations • CS connections must be made within the same DHLC/DLC card. • When a wrong connection is made, satisfactory performance of the CS cannot be guaranteed. Check the connection of CS and the PBX using the KX-TDE Maintenance Console. For information about how to view CS information using the KX-TDE Maintenance Console, refer to "2.5.15 Utility—CS Information"...
  • Page 175 3.9 Connection of DECT Portable Stations Connecting the CS Connect the cable from the CSIF/DHLC/DLC card to the CS. KX-TDA0158CE KX-TDA0141CE/KX-TDA0142CE Modular Modular To DHLC/DLC card To CSIF/DHLC/DLC card Pass the cable through the groove of the CS (in any direction depending on your preference). KX-TDA0158CE KX-TDA0141CE/KX-TDA0142CE To CSIF/DHLC/DLC card...
  • Page 176 3.9 Connection of DECT Portable Stations For the KX-TDA0142CE User only: Wrap the cable once around the ferrite core. Then close the case of the ferrite core. To CSIF card Note If you need to open the ferrite core, use a flathead screwdriver to unlatch the case of the ferrite core. Installation Manual...
  • Page 177 3.9 Connection of DECT Portable Stations Registering the PS The PS must be registered to the PBX before it can be used. Programming of both the PS and PBX is required. A PT with multiline display (e.g., KX-T7636 6-line display) is required to perform the PBX system programming.
  • Page 178 3.9 Connection of DECT Portable Stations Using the KX-TD7590 System lock can be set after PS registration. When system lock is enabled, the system lock password will be required for system setting. Press POWER for 5 seconds. To register for the first time SELECT Select "INITIAL SETTING".
  • Page 179 3.9 Connection of DECT Portable Stations Setting the Personal Identification Number (PIN) for PS Registration To prevent registering the PS to a wrong PBX, a PIN for PS registration can be set to the PBX. Before registering the PS to the PBX, enter the PIN set to the PBX into the PS. By doing so, the PS will only be registered to the PBX with the matching PIN.
  • Page 180 3.9 Connection of DECT Portable Stations PS Termination Confirm the following before cancelling the PS registration: • The PS is turned on. • The PS is within range. [691] PS No. 001 to 128 ENTER ENTER If "Rejected" or "Time out" is displayed CLEAR To the PS operation...
  • Page 181 3.9 Connection of DECT Portable Stations Testing the Operation Walk around the service area while having a conversation using a registered PS. If noise is frequent or conversations disconnect, relocate the CSs or install an additional CS. Installation Manual...
  • Page 182: Wall Mounting

    3.9 Connection of DECT Portable Stations 3.9.8 Wall Mounting Mounting the KX-TDA0158CE Place the reference for wall mounting (KX-TDA0158CE) on the wall to mark the 2 screw positions. Install the 2 screws and washers (included) into the wall. Notes • Make sure that the screw heads are at the same distance from the wall.
  • Page 183 3.9 Connection of DECT Portable Stations Reference for Wall Mounting (KX-TDA0158CE) Please copy this page and use as a reference for wall mounting. Install a screw here. 83 mm Install a screw here. Note Make sure to set the print size to correspond with the size of this page. If the dimension of the paper output still deviates slightly from the measurement indicated here, use the measurement indicated here.
  • Page 184 3.9 Connection of DECT Portable Stations Mounting the KX-TDA0141CE/KX-TDA0142CE Place the reference for wall mounting (KX-TDA0141CE/KX-TDA0142CE) on the wall to mark the 2 screw positions. Install the 2 screws and washers (included) into the wall. Notes • Make sure that the screw heads are at the same distance from the wall. •...
  • Page 185 3.9 Connection of DECT Portable Stations Reference for Wall Mounting (KX-TDA0141CE/KX-TDA0142CE) Please copy this page and use as a reference for wall mounting. Install a screw here. 71 mm Install a screw here. Note Make sure to set the print size to correspond with the size of this page. If the dimension of the paper output still deviates slightly from the measurement indicated here, use the measurement indicated here.
  • Page 186: Connection Of 2.4 Ghz Portable Stations

    3.10 Connection of 2.4 GHz Portable Stations 3.10 Connection of 2.4 GHz Portable Stations 3.10.1 Overview Required Equipment and Maximum Number of Calls CSs determine the area covered by the wireless system. The number of calls that can be made simultaneously through each CS varies depending on the model, as follows: Connection Card Maximum Calls...
  • Page 187: Procedure Overview

    3.10 Connection of 2.4 GHz Portable Stations 3.10.2 Procedure Overview When connecting the wireless system, use extreme care in conducting the site survey. An incorrectly performed site survey can result in poor service area, frequent noise, and disconnection of calls. 1.
  • Page 188 3.10 Connection of 2.4 GHz Portable Stations Make sure that adjacent CS coverage areas overlap where the radio signal strength level is "8" by at least 5 m. Make sure that the radio signal strength level is greater than "3" at any location within the service area required by the user.
  • Page 189: Site Planning

    3.10 Connection of 2.4 GHz Portable Stations 3.10.3 Site Planning Choosing the best site for the CS requires careful planning and testing of essential areas. The best location may not always be convenient for installation. Read the following information before installing the unit. Understanding Radio Waves Characteristics of Radio Waves The transmission of radio waves and the CS coverage area depend on the structure and materials of the...
  • Page 190 3.10 Connection of 2.4 GHz Portable Stations Object Material Transmission Tendency Wall Concrete The thicker they are, the less radio waves penetrate them. Ferroconcrete Radio waves can penetrate them, but the more iron there is, the more radio waves are reflected. Window Glass Radio waves usually penetrate them.
  • Page 191 3.10 Connection of 2.4 GHz Portable Stations CS Coverage Area The example below shows the size of the coverage area of 1 CS if it is installed in an area with no obstacles. Note Radio signal strength levels are measured during the site survey (refer to "3.10.5 Site Survey"). Coverage Area Radio signal strength level is greater than "3".
  • Page 192 3.10 Connection of 2.4 GHz Portable Stations one CS becomes weak. However, if a PS moves away from a CS and there are no CSs available for handover, the PS may go out of range and the call could be lost. If the signal from the CS fades, due to the structure of the building, there may be some handover delay.
  • Page 193: Before Site Survey

    3.10 Connection of 2.4 GHz Portable Stations 3.10.4 Before Site Survey Setting and Installing the CS Temporarily for Site Survey Switch the Radio Signal Test switch from OFF to ON. Set the CS number switches as desired. Set the Power Supply Select switch as desired (KX-TDA0151/KX-TDA0152 only). KX-TDA0151/KX-TDA0152 CS no.
  • Page 194 3.10 Connection of 2.4 GHz Portable Stations KX-TDA0141/KX-TDA0142 DIP Switch CS Number Switch Keep this switch at the default "OFF" position. Otherwise, the CS will not function. Radio Signal Test Switch CS no. 1 CS no. 2 CS no. 3 CS no.
  • Page 195 3.10 Connection of 2.4 GHz Portable Stations After setting the DIP switch, connect the CS to an AC adaptor/battery box using a power supply adaptor, or connect to a CSIF/DLC/DHLC card. Notes • The AC adaptor should be connected to a vertically oriented or floor-mounted AC outlet. Do not connect the AC adaptor to a ceiling-mounted AC outlet, as the weight of the adaptor may cause it to become disconnected.
  • Page 196: Site Survey

    3.10 Connection of 2.4 GHz Portable Stations 3.10.5 Site Survey The PS has a Radio Signal Test mode that monitors the state of the radio link to the CS. After installing the CSs temporarily, set the PS to Radio Signal Test mode and measure each CS coverage area. Then, record the results on the map of the installation site.
  • Page 197 3.10 Connection of 2.4 GHz Portable Stations Measure the radio signal strength by moving towards and away from the CS. Move to the CS until the radio signal strength level becomes "12". Move away from the CS and identify the CS coverage area within which the radio signal strength level is greater than "8".
  • Page 198 3.10 Connection of 2.4 GHz Portable Stations Overlap the CS coverage areas of at least 2 CSs at any location in the installation site. CS no. 1 CS no. 2 CS no. 3 CS no. 4 Make sure that the radio signal strength level is greater than "3" at any location in the service area required by the user.
  • Page 199 3.10 Connection of 2.4 GHz Portable Stations Using the KX-TD7690 Display example: When there is scan data Scan Data No. NO.1 CS No.2 LEVEL: 9 Press 1, 9, and POWER 0 to 9 for more than 2 seconds. When there is no scan data NO.0 NOT SAVED To the Desired Scan Data No.
  • Page 200: After Site Survey

    3.10 Connection of 2.4 GHz Portable Stations 3.10.6 After Site Survey After obtaining the proper measurement results, exit Radio Signal Test mode before connecting the CS to the PBX. Keep pressing the POWER button on the PS until the PS is turned OFF. Disconnect the CS from the AC adaptor/battery box or the CSIF/DLC/DHLC card, and stop supplying electricity.
  • Page 201: Connecting A Cell Station To The Pbx

    3.10 Connection of 2.4 GHz Portable Stations 3.10.7 Connecting a Cell Station to the PBX Using a CSIF Card Refer to the following example to connect a CS to the PBX. KX-TDA0152/KX-TDA0142 CSIF8 Card Port 1 Cable Maximum Distance ø 0.4 mm: 444 m ø...
  • Page 202 3.10 Connection of 2.4 GHz Portable Stations Using a DHLC/DLC Card Refer to the following example to connect a CS to the PBX. KX-TDA0151/KX-TDA0141 DHLC8 Card Cable Maximum Distance ø 0.4 mm: 222 m ø 0.5 mm: 347 m ø 0.6 mm: 500 m CAT 5: 347 m...
  • Page 203 3.10 Connection of 2.4 GHz Portable Stations Connecting the CS Connect the cable from the CSIF/DHLC/DLC card to the CS. KX-TDA0151/KX-TDA0152 KX-TDA0141/KX-TDA0142 Modular Modular To CSIF/DHLC/DLC card To CSIF/DHLC/DLC card Pass the cable through the groove of the CS (in any direction depending on your preference). KX-TDA0151/KX-TDA0152 KX-TDA0141/KX-TDA0142 To CSIF/DHLC/DLC card...
  • Page 204 3.10 Connection of 2.4 GHz Portable Stations Registering the PS The PS must be registered to the PBX before it can be used. Programming of both the PS and PBX is required. A PT with multiline display (e.g., KX-T7636 6-line display) is required to perform the PBX system programming.
  • Page 205 3.10 Connection of 2.4 GHz Portable Stations PS Registration [690] PS No. Extn. No. To the PS operation 001 to 128 1 to 4 digits below ENTER ENTER When the PS has not been registered yet When registering the PS for the first time, it is possible to select the desired language for the display. (You do not need to enter the PS system programming mode when registering for the first time.) Using the KX-TD7684/KX-TD7694 C.Tone...
  • Page 206 3.10 Connection of 2.4 GHz Portable Stations Setting the System Lock When a system lock has been set, the system lock password will be required for PS system setting. Using the KX-TD7684/KX-TD7694 Select Choose "On/Off". "SYSTEM LOCK". System Lock Password System Lock Password 4 digits 4 digits...
  • Page 207 3.10 Connection of 2.4 GHz Portable Stations Setting the Personal Identification Number (PIN) for PS Registration To prevent registering the PS to a wrong PBX, a PIN for PS registration can be set to the PBX. Before registering the PS to the PBX, enter the PIN set to the PBX into the PS. By doing so, the PS will only be registered to the PBX with the matching PIN.
  • Page 208 3.10 Connection of 2.4 GHz Portable Stations PS Termination Confirm the following before cancelling the PS registration: • The PS is turned on. • The PS is within range. [691] PS No. 001 to 128 ENTER ENTER If "Rejected" or "Time out" is displayed CLEAR To the PS operation...
  • Page 209: Wall Mounting

    3.10 Connection of 2.4 GHz Portable Stations 3.10.8 Wall Mounting Mounting the KX-TDA0151/KX-TDA0152 Place the reference for wall mounting (KX-TDA0151/KX-TDA0152) on the wall to mark the 2 screw positions. Install the 2 screws and washers (included) into the wall. Notes •...
  • Page 210 3.10 Connection of 2.4 GHz Portable Stations CAUTION Make sure the cables are securely fastened to the wall. Reference for Wall Mounting (KX-TDA0151/KX-TDA0152) Please copy this page and use as a reference for wall mounting. Install a screw here. 83 mm Install a screw here.
  • Page 211 3.10 Connection of 2.4 GHz Portable Stations Mounting the KX-TDA0141/KX-TDA0142 Place the reference for wall mounting (KX-TDA0141/KX-TDA0142) on the wall to mark the 2 screw positions. Install the 2 screws and washers (included) into the wall. Notes • Make sure that the screw heads are at the same distance from the wall. •...
  • Page 212 3.10 Connection of 2.4 GHz Portable Stations Reference for Wall Mounting (KX-TDA0141/KX-TDA0142) Please copy this page and use as a reference for wall mounting. Install a screw here. 71 mm Install a screw here. Note Make sure to set the print size to correspond with the size of this page. If the dimension of the paper output still deviates slightly from the measurement indicated here, use the measurement indicated here.
  • Page 213: Connection Of Doorphones, Door Openers, External Sensors, And External Relays

    3.11 Connection of Doorphones, Door Openers, External Sensors, and External Relays 3.11 Connection of Doorphones, Door Openers, External Sensors, and External Relays 3.11.1 Connection of Doorphones, Door Openers, External Sensors, and External Relays The PBX supports a maximum of 16 doorphones (KX-T30865 with a DPH4 card, or German-type doorphone with a DPH2 card), 16 door openers, 16 external sensors, and 16 external relays.
  • Page 214 3.11 Connection of Doorphones, Door Openers, External Sensors, and External Relays Pass the wires through the hole in the base cover, and attach the base cover to a wall using 2 screws. Screw To 8-pin terminal block Note Two kinds of screws are included with a KX-T30865. Please choose the appropriate kind for your wall type.
  • Page 215 3.11 Connection of Doorphones, Door Openers, External Sensors, and External Relays Attach the terminal blocks to the connectors of the DPH4/DPH2/EIO4 card on the PBX. To doorphones/ door openers/ external sensors/ external relays Installation Manual...
  • Page 216: Connection Of Peripherals

    3.12 Connection of Peripherals 3.12 Connection of Peripherals 3.12.1 Connection of Peripherals Maximum Distance Cable Maximum Distance ø 0.4 mm: 10 m ø 0.5 mm: 10 m MNT Port ø 0.6 mm: 10 m CAT 5: 10 m Cable Maximum Distance ø...
  • Page 217 3.12 Connection of Peripherals BGM/MOH The PBX provides Background Music and Music on Hold. Up to 2 external music sources (e.g., user- supplied radios) can be connected to the PBX. CAUTION • Wiring should be done carefully to prevent undue force being exerted on the plug. Otherwise, sound may only be heard intermittently.
  • Page 218 3.12 Connection of Peripherals Connection Charts For connecting a printer/PC with a 9-pin RS-232C connector PBX (9-pin) Printer/PC (9-pin) Circuit Type Signal Signal Circuit Type Pin No. Pin No. (EIA) Name Name (EIA) RD (RXD) RD (RXD) SD (TXD) SD (TXD) ER (DTR) ER (DTR) DR (DSR)
  • Page 219 3.12 Connection of Peripherals • Clear To Send (CTS):…(input) An ON condition of circuit CS (CTS) indicates that the printer or the PC is ready to receive data from the unit. The unit does not attempt to transfer data or receive data when circuit CS (CTS) is OFF.
  • Page 220: Lan Connection

    3.13 LAN Connection 3.13 LAN Connection 3.13.1 LAN Connection Connection Chart for LAN Connection The PBX is equipped with a LAN port for connecting to a LAN so that IP telephones (IP-PTs, IP softphones, SIP Extensions), PCs and a CTI Server can be connected on a private IP network. IP Softphone LAN Port CTI Server...
  • Page 221: Power Failure Connections

    3.14 Power Failure Connections 3.14 Power Failure Connections 3.14.1 Power Failure Connections When the power supply to the PBX fails, power failure transfer (PFT) will switch from the current connection to the Power Failure Connection. Refer to "2.4.1 Power Failure Transfer" in the Feature Guide for further information.
  • Page 222 3.14 Power Failure Connections RJ11 Connector Pin Assignments for Analogue Trunk Card PFT Ports 1 and 2 Signal Name Function Ring port 2 Ring port 1 Tip port 1 Tip port 2 PFT Ports 3 and 4 (for LCOT16 card only) Signal Name Function Ring port 4...
  • Page 223 3.14 Power Failure Connections Using BRI Card LINE 1 and LINE 2 of the BRI4 and BRI8 cards can be used for Power Failure Connections. Note When the power returns, the connection will switch back to normal configuration from the Power Failure Connection, and a trunk conversation established during power failure will be dropped.
  • Page 224 3.14 Power Failure Connections RJ45 Connector LINE 2 Pin Assignments Signal Name Level [V] Function Reserved – – Receive data 2 Transmit data 1 Transmit data 2 Receive data 1 Reserved – – Installation Manual...
  • Page 225: Starting The Pbx

    3.15 Starting the PBX 3.15 Starting the PBX 3.15.1 Starting the PBX CAUTION • The SD Memory Card must be inserted in the SD Memory Card slot of the IPCMPR card before startup. • Before touching the System Initialise Switch, discharge static electricity by touching ground or wearing an earthing strap.
  • Page 226 3.15 Starting the PBX Plug the AC power cord into the PBX and an AC outlet, and turn on the PBX. The RUN indicator will flash. Note For safety reasons, do not stretch, bend, or pinch the AC power cord. To AC Outlet While the RUN indicator is flashing, slide the System Initialise Switch back to the "NORMAL"...
  • Page 227: Guide For The Kx-Tde Maintenance Console

    Section 4 Guide for the KX-TDE Maintenance Console Explains the installation procedure, structure, and basic information of the KX-TDE Maintenance Console. Installation Manual...
  • Page 228: Overview

    4.1 Overview Overview 4.1.1 Overview KX-TDE Maintenance Console is designed to serve as an overall system programming reference for the PBX. To programme and administer the PBX by PC, you need to install the KX-TDE Maintenance Console onto the PC. This section describes overview and installation of the KX-TDE Maintenance Console only.
  • Page 229: Pc Connection

    4.2 PC Connection PC Connection 4.2.1 PC Connection Connection via MNT Port of IPCMPR Card MNT Port To LAN Port IMPORTANT When connecting a PC to the PBX, a fixed IP address must be assigned to the PC. For information about fixed IP addresses, ask your network administrator. Note For pin assignments and maximum cabling distance, refer to "3.12.1 Connection of Peripherals".
  • Page 230 4.2 PC Connection CAUTION Use an RS-232C cross cable (shielded cable) for connection between the PBX and PC. Make sure to connect both the PBX and the PC to earth. Note For pin assignments and maximum cabling distance, refer to "3.12.1 Connection of Peripherals". External Modem Connection Modem To RS-232C port (25-pin)
  • Page 231: Installation Of The Kx-Tde Maintenance Console

    4.3 Installation of the KX-TDE Maintenance Console Installation of the KX-TDE Maintenance Console 4.3.1 Installing and Starting the KX-TDE Maintenance Console System Requirements Required Operating System • Microsoft Windows 2000, Windows XP, or Windows Vista™ Business ® ® Minimum Hardware Requirements •...
  • Page 232 4.3 Installation of the KX-TDE Maintenance Console Starting the KX-TDE Maintenance Console and Assigning the Basic Items (Quick Setup) When you start the KX-TDE Maintenance Console with the Installer Level Programmer Code and connect to the PBX for the first time after initialisation (with the factory default setting), Quick Setup will launch automatically.
  • Page 233 4.3 Installation of the KX-TDE Maintenance Console is reset for some reason, all the system data in RAM will be lost. However, if system data has been saved to the SD Memory Card, it can be easily restored. To save the system data to the SD Memory Card, (1) click the "SD Memory Backup" icon before resetting the PBX or turning off the power, or (2) exit the KX-TDE Maintenance Console so that the PBX automatically saves the system data.
  • Page 234 4.3 Installation of the KX-TDE Maintenance Console Installation Manual...
  • Page 235: Troubleshooting

    Section 5 Troubleshooting This section provides information on the PBX and telephone troubleshooting. Installation Manual...
  • Page 236: Troubleshooting

    5.1 Troubleshooting Troubleshooting 5.1.1 Installation PROBLEM PROBABLE CAUSE SOLUTION You cannot make/receive calls • IP-EXT/IP-GW/DSP card • Replace the corresponding card. via an IP network. malfunction • IPCMPR card malfunction • Replace the IPCMPR card (be sure to turn off the PBX when replacing). •...
  • Page 237 5.1 Troubleshooting PROBLEM PROBABLE CAUSE SOLUTION • Network malfunction • Make sure that all network devices in use are switched on. • Make sure that the IP-PT/SIP Extension is not blocked by the firewall or other network devices. Extensions (except IP-PT/SIP •...
  • Page 238 5.1 Troubleshooting PROBLEM PROBABLE CAUSE SOLUTION The LINK indicator of the IP- • IP-EXT/IP-GW card • Replace the corresponding card. EXT/IP-GW/IPCMPR does not malfunction turn on. • IPCMPR card malfunction • Replace the IPCMPR card (be sure to turn off the PBX when replacing). •...
  • Page 239: Connection

    5.1 Troubleshooting 5.1.2 Connection Connection between the PBX and a PT: CAUSE SOLUTION Can you dial The T/R is connected to the D1/D2. Use the correct cord (the an extension? inner 2 wires are for T/R and the outer 2 wires are for D1/D2) Extension Connection between the PBX and an SLT:...
  • Page 240 5.1 Troubleshooting Connection between the trunk and the PBX: CAUSE SOLUTION (Continued from the Trunk is connected to the T2/T1. Reconnect the trunk to previous page.) the T1/R1 or T2/R2 of the telephone jack using 2- conductor wiring. Can you dial out on a Trunk trunk?
  • Page 241: Operation

    5.1 Troubleshooting 5.1.3 Operation PROBLEM PROBABLE CAUSE SOLUTION • Cannot set the IP address, • An unusable value is being • Set an IP address within the valid subnet mask address, and set. range. IP address of the IP-PT/PBX: PBX IP address to the IP- "1.0.0.0"...
  • Page 242 5.1 Troubleshooting PROBLEM PROBABLE CAUSE SOLUTION • Cannot register the PS. • Wrong Personal • Enter the PIN set to the PBX into the Identification Number (PIN) is registered to the PS. • CS is not connected • Make sure that the cable is connected properly.
  • Page 243: Using The Reset Button

    5.1 Troubleshooting 5.1.4 Using the Reset Button If the PBX does not operate properly, use the Reset Button. Before using the Reset Button, try the system feature again to confirm whether there definitely is a problem or not. CAUTION In order to avoid possible corruption of data on the SD Memory Card, please ensure that the "SD ACCESS"...
  • Page 244: Troubleshooting By Error Log

    5.1 Troubleshooting 5.1.5 Troubleshooting by Error Log When a major system error occurs in the PBX, the ALARM indicator on the front of the shelf turns on red, and the system logs the error information. Error Log Display Format Below is the display format of the error log. For information about how to view the error log using the KX- TDE Maintenance Console, refer to "2.5.8 Utility—Error Log"...
  • Page 245 • 1: Shelf number • YY: Slot number – KX-TDE100 (Physical slot): 00 to 06 (00: IPCMPR Card Slot; 01 to 06: Free Slots) – KX-TDE200 (Physical slot): 00 to 11 (00: IPCMPR Card Slot; 01 to 11: Free Slots) –...
  • Page 246 5.1 Troubleshooting Installation Manual...
  • Page 247: Index

    Index Installation Manual...
  • Page 248 Index Numerics Basic Shelf, Construction 16-Channel Echo Canceller Card (KX-TDA0166) 29, 143 Blank Slot Cover (KX-A258) 16-Channel SIP Extension Activation Key (KX-NCS4716) BRI4 Card (KX-TDA0284) 16-Channel VoIP DSP Card (KX-TDE0110) 29, 85 BRI8 Card (KX-TDA0288) 16-Channel VoIP Extension Card (KX-TDA0470) 31, 132 16-Channel VoIP Gateway Card (KX-TDA0490) 31, 116...
  • Page 249 KX-TDA0173 (8-Port Single Line Telephone Extension Card) 30, 127 KX-TDA0174 (16-Port Single Line Telephone Extension Card) 30, 130 Pager KX-TDA0175 (16-Port Single Line Telephone Extension with Message Lamp Panasonic Proprietary Telephones, Compatible Card) 30, 130 Panasonic Proprietary Telephones, Incompatible KX-TDA0180 (8-Port Analogue Trunk Card) 30, 88...
  • Page 250 RMT Card (KX-TDA0196) V-SIPGW16 (Virtual 16-Channel SIP Trunk Card) RUN Indicator Wall Mounting (CS) 182, 209 Safety Installation Instructions Wall Mounting (KX-TDE100) Safety Instructions Wall Mounting (KX-TDE200) SD Memory Card Wiring Precautions Site Planning, 2.4 GHz Portable Station Site Planning, DECT Portable Station Site Survey, 2.4 GHz Portable Station...
  • Page 251 Index Installation Manual...
  • Page 252 Copyright: This material is copyrighted by Panasonic Communications Co., Ltd., and may be reproduced for internal use only. All other reproduction, in whole or in part, is prohibited without the written consent of Panasonic Communications Co., Ltd. 2007 Panasonic Communications Co., Ltd. All Rights Reserved.

This manual is also suitable for:

Kx-tde200

Table of Contents