Bosch AMAX 2100 User Manual
Hide thumbs
Also See for AMAX 2100:
- Installation manual (164 pages) ,
- Operation manual (52 pages) ,
- Quick start manual (38 pages)
Table of Contents
Advertisement
Advertisement
Table of Contents
Subscribe to Our Youtube Channel
Related Manuals for Bosch AMAX 2100
Summary of Contents for Bosch AMAX 2100
- Page 1 AMAX 2100 / 3000 / 4000 User Guide...
-
Page 3: Table Of Contents
Reset the Control Panel Bypassing Bypassing Zones Codes Add/Change and Delete User Code Change Individual Code Keypad Alarm Operation Commands Keypad Panic Alarm Keypad Fire Alarm Keypad Medical Alarm Domestic Dialing Bosch Sicherheitsysteme GmbH User Guide 2014.01 | 02 | F.01U.295.569... -
Page 4: Introduction
| Introduction AMAX Introduction IUI-AMAX4-TEXT IUI-AMAX3-LED8 IUI-AMAX3-LED16 IUI-AMAX-LED8 IUI-AMAX-LCD8 2014.01 | 02 | F.01U.295.569 User Guide Bosch Sicherheitsysteme GmbH... - Page 5 Keypad Medical Alarm Long press [7] and [9] D = Duress User A = Arming User B = Basic User S = Super User M = Master User IN = Install User Bosch Sicherheitsysteme GmbH User Guide 2014.01 | 02 | F.01U.295.569...
- Page 6 [Code] + [9][5][8] + [#] √ D = Duress User A = Arming User B = Basic User S = Super User M = Master User IN = Install User 2014.01 | 02 | F.01U.295.569 User Guide Bosch Sicherheitsysteme GmbH...
- Page 7 PRINT ENABLE RESET SYSTEM SETTINGS DAYL.SAV.TIME +1h DAYL.SAV.TIME -1h ADD/CHG USER CODE CHANGE INDIV CODE INITIATE CALL BACK CHANGE LANGUAGE INSTALLER ACCESS ENABLE INSTALLER DISABLE INSTALLER Figure 1.1: User Menu Bosch Sicherheitsysteme GmbH User Guide 2014.01 | 02 | F.01U.295.569...
- Page 8 AC main power supply failed. MAINS second lights off) System fault or Tamper condition is present. System is in normal status. FAULTS Flashes System fault or Tamper condition must be acknowledged. System is disarmed. 2014.01 | 02 | F.01U.295.569 User Guide Bosch Sicherheitsysteme GmbH...
- Page 9 Last 10s on exit time – Keypad fault/tamper sound (fault/tamper to be acknowledged) – Keypad alarm sound Continuous 0.5 second beep, stops Entry delay time (until alarm ends or system is 0.5 seconds disarmed). Bosch Sicherheitsysteme GmbH User Guide 2014.01 | 02 | F.01U.295.569...
-
Page 10: Arming And Disarming The System
AWAY indicator flashes slow and exit time starts. After exit time, the AWAY indicator is lit. When the Key switch is deactivated, the system is disarmed and Away indicator is off. 2014.01 | 02 | F.01U.295.569 User Guide Bosch Sicherheitsysteme GmbH... -
Page 11: Arming In Stay Mode
Enter your code and press [#] .It beeps twice and the AWAY or STAY indicator is extinguished. 2.2.2 Disarming with Key Switch When the Key switch is deactivated, the system is disarmed and the AWAY or STAY indicator is extinguished. Bosch Sicherheitsysteme GmbH User Guide 2014.01 | 02 | F.01U.295.569... -
Page 12: Faults And Tamper Conditions
Enter your Code + [2] [1] and press [#]. It beeps twice. b) Scroll down with [ arrow] to display all trouble or fault conditions. c) To exit from Fault and Tamper Analysis Mode, press [#]. 2014.01 | 02 | F.01U.295.569 User Guide Bosch Sicherheitsysteme GmbH... - Page 13 1 - 2 Panel Aux Power 1 - 2 Fault Bosch Option Bus Power Failure 1 - 2 Bosch Option Bus 1 - 2 Power Fault RF Repeater AC Power Failure 1 - 8 RF Repeater 1-8 AC Power Fault...
- Page 14 Keypad Lock out 1 Keypad Lock out RF Receiver Tamper 1 RF Receiver Tamper RF Repeater Tamper 1 - 8 RF Repeater Tamper External Failure 1 - 16 External Fault Zone 1-16 2014.01 | 02 | F.01U.295.569 User Guide Bosch Sicherheitsysteme GmbH...
-
Page 15: System Test
Unseal and seal the zones to be tested. The keypad sounds one second beep and the siren sounds one beep each time when a Zone status is changed. To exit Walk Test Mode: Enter your Code + [4] [3] and press [#]. Bosch Sicherheitsysteme GmbH User Guide 2014.01 | 02 | F.01U.295.569... -
Page 16: Event Log Recall Mode
Enter your code + [2] [4] and press [#]. It beeps twice. Press [▲] or [▼] to move up and down in the Event Logs Press [ #] To exit the Event Log 2014.01 | 02 | F.01U.295.569 User Guide Bosch Sicherheitsysteme GmbH... -
Page 17: Reset The Control Panel
Enter your code + [6][#]. The keypad beeps twice and the signal is eliminated. Notice! You can reset alarms, faults or tamper conditions, only when they are not active anymore. Bosch Sicherheitsysteme GmbH User Guide 2014.01 | 02 | F.01U.295.569... -
Page 18: Bypassing
Enter your code + [3] [3] and press [#]. It beeps twice. b) Move up and down with [▲] or [▼] to display all bypassed zones. c) Press [#] to exit. 2014.01 | 02 | F.01U.295.569 User Guide Bosch Sicherheitsysteme GmbH... -
Page 19: Codes
Enter the user number (1-64) and press [#]. c) Enter the user code priority (0-15) and press [#]. 00 = Master User 01 = Super User 02 = Basic User Bosch Sicherheitsysteme GmbH User Guide 2014.01 | 02 | F.01U.295.569... -
Page 20: Change Individual Code
Enter the new code (Default code length=4 digits / 5or 6 digit code must be enabled through the installer) and press [#]. It beeps twice and the STAY and AWAY indicators stop flashing. 2014.01 | 02 | F.01U.295.569 User Guide Bosch Sicherheitsysteme GmbH... -
Page 21: Keypad Alarm Operation Commands
If you simultaneously press and hold [7] and [9] for 3 seconds a silent keypad medical alarm will be transmitted. Please contact your installer to enable/disable the emergency medical alarm functionality. Bosch Sicherheitsysteme GmbH User Guide 2014.01 | 02 | F.01U.295.569... -
Page 22: Domestic Dialing
The user presses [#] between two acknowledgement tones to confirm the alarm. If the control panel got the [#] acknowledgement from the user, it will send a 2 second long beep as acknowledge tone and hang up the line. 2014.01 | 02 | F.01U.295.569 User Guide Bosch Sicherheitsysteme GmbH... - Page 24 Bosch Sicherheitssysteme GmbH Robert-Bosch-Ring 5 85630 Grasbrunn Germany www.boschsecurity.com © Bosch Sicherheitssysteme GmbH, 2014...
Need help?
Do you have a question about the AMAX 2100 and is the answer not in the manual?
Questions and answers