JVC SR-VS30E Instructions Manual page 37

G
Check the programme data.
The S V number you
HOW IEW
entered and the matching
timer-recording information
are displayed on the TV
screen. Check they are
correct.
The front display panel shows the programme start time.
Pressing changes the display to the programme stop
"
time, then the date and channel position.
IMPORTANT
Make sure the channel position number you wish to record is
displayed; if not, see "S
HOW
and set the Guide Program number correctly.
H
Set the tape speed.
Press SP/LP ( ).
p
I
Set the VPS/PDC mode.
Press VPS/PDC to select "ON" or "OFF".
If "VPS/PDC ON" is displayed on the TV screen or "VPS/PDC"
is lit on the front display panel, VPS/PDC is set to ON.
If "VPS/PDC OFF" is displayed on the TV screen or "VPS/PDC"
is not lit on the front display panel, VPS/PDC is set to OFF.
"VPS/PDC Recording" on page 39.
J
Return to the normal screen.
Press PROG or OK. "PROGRAM COMPLETED" appears
on the TV screen for about 5 seconds, then the normal
screen appears. If "PROGRAM OVERLAPPED" appears
on the TV screen and "Err" on the front display panel, see
page 43.
Repeat steps 3 – 10 for each additional programme.
K
Engage the recorder's timer mode.
Press (TIMER). The recorder turns off automatically and
#
" " appears on the front display panel.
#
To disengage the timer mode, press
Satellite Receiver Users
To timer-record a satellite broadcast using the S
system:
A Perform "Satellite Receiver Control Setting" on page 17.
B Perform steps 1 – 11. In step 7, the front display panel
shows "L2" for the channel position. In step 9, you cannot
set "VPS/PDC" to "ON".
C Leave the satellite receiver's power on.
V ® System Setup" on page 82
IEW
(TIMER) again.
#
V
HOW IEW
NOTES:
To Change The Stop Time . . .
. . . press STOP +/– in step 7. You can compensate for
anticipated programme schedule delays.
To Timer-Record Weekly Or Daily Serials . . .
. . . in step 7, press WEEKLY (number key "9") for weekly
serials or DAILY (number key "8") for daily serials (Monday —
Friday). Either "WEEKLY" or "DAILY" appears on the TV
screen. Pressing the button again makes the corresponding
indication disappear.
You can programme each deck to timer-record as many as 6
programmes. If you try to programme the recorder to record a
seventh, "PROGRAM FULL" appears on the TV screen and
"FULL" appears on the front display panel. To record the extra
programme, you must first cancel any unnecessary
programmes ( pg. 42).
It is not possible to timer-record a TV programme with a
S V number which starts with "0".
HOW IEW
It is not possible to timer-record a satellite broadcast received
on the channel position "0" by the satellite receiver.
It is not possible to timer-record the same programme on both
the VHS deck and the DV deck simultaneously.
During timer recording, it is not possible to change the
recording deck (VHS or DV).
If the times that are programmed for recording on the DV deck
and on the VHS deck overlap, the earlier start time takes
precedence. If the start times are the same, the VHS deck takes
precedence.
INFORMATION
Instead of the steps 4 – 6, you can enter the S
number using the on-screen menu.
A Press PROG to access the S
B Press the number keys to
enter the S V number
HOW IEW
of a programme you wish to
record.
If you make a mistake,
press and input the
&
correct number.
C Press OK, then go to step 7
in the left column.
If the number you entered
is invalid, "ERROR" appears on the TV screen and "Err"
appears on the front display panel. Input a valid
S V number.
HOW IEW
If the "GUIDE PROG SET" screen appears, see
"ATTENTION" below.
ATTENTION
Guide Program Number Set
"GUIDE PROG SET" appears after performing step C above
if the Guide Program number for the S
entered has not been set.
If you want to set the Guide Program number for the satellite
broadcast station, press the number key "0" to change "TV
PROG" to "SAT". Press
rt
number on which your recorder or satellite receiver receives
that station, then press OK or
number. The S V
HOW IEW
EN
V
HOW
V screen.
HOW IEW
V number you
HOW IEW
to input the channel position
to set the Guide Program
e
Program screen appears.
(Example)
To timer-record a ZDF
programme with the
S V system.
HOW IEW
* If your recorder receives ZDF on
the channel position 2, press
OK
or after entering "2".
e
37
IEW