Related Manuals for Partner K650 ACTIVE III
Summary of Contents for Partner K650 ACTIVE III
- Page 1 K650 ACTIVE III K700 ACTIVE III Operator’s manual Read through the Operator’s Manual carefully and understand the content before using the power cutter.
-
Page 2: Symbol Explanation
SYMBOL EXPLANATION Symbols on the power cutter: Symbols in the Operator's Manual: WARNING! The power cutter can be dangerous! Careless or incorrect usage can Switch off the engine by moving the stop result in serious injury even death to the switch to the STOP position before carrying operator or others. -
Page 3: Table Of Contents
Cutting ................. 6 correctly! Kickback ................7 • Let your Partner dealer check the power cutter and make Care and storage ..............8 essential adjustments and repairs. Cutting blades .............. -
Page 4: Safety Instructions
SAFETY INSTRUCTIONS THE POWER CUTTER’S SAFETY WARNING! A power cutter is a dangerous tool EQUIPMENT if used carelessly or incorrectly and can cause serious, even fatal injuries. It is extremely This section explains the various safety features of the power important that you read and understand this cutter, how they work, and basic inspection and maintenance manual. -
Page 5: General Safety Instructions
SAFETY INSTRUCTIONS 2 Stop switch 4 Blade guard for the cutting blade The stop switch should be WARNING! Always check that the blade used to stop the engine. guard is correctly fitted before starting the machine. Start the engine and make sure that the engine stops This guard is fitted above the when the stop switch is... -
Page 6: Fuel Safety
Only use the machine in areas with good ventilation. Neglect can result in serious injury WARNING! Use a Partner fuel can with an or death. Carbon monoxide in the exhaust anti-spill device. Fuel and fuel fumes are fumes causes suffocation. -
Page 7: Cutting Technique
SAFETY INSTRUCTIONS Water cooling Over exposure to vibrations can result in blood-vessel or nerve injury to persons WARNING! suffering with blood circulation problems. Water cooling, which is only used on petrol Seek medical attention if you experience driven power cutters and when cutting physical symptoms that can be related to over concrete, cools the blade and increases its exposure to vibrations. -
Page 8: Care And Storage
General ” How to avoid kickback ” and ”Pinching/rotation” below) Partner’s power cutters are robust and durable. However, as they are used at a high processing rate all service procedures must be carried out at the times and in the manner described, Pinching/rotation so that the machine always works efficiently and safely. -
Page 9: Cutting Blades
SAFETY INSTRUCTIONS Abrasive discs CUTTING BLADES The cutting material on abrasive discs consists of grit bonded using an organic binder. ”Reinforced blades” are made up of a fabric or fibre base that prevents total breakage at maximum working speed if the blade should be cracked or damaged. (The term reinforced does not refer to those cutting blades that are only reinforced around the flange). -
Page 10: Cutting Blades
SAFETY INSTRUCTIONS Type of cutting blades Guard Check that the blade is Check that the guard is not approved for the same or cracked or shows signs of any higher speed according to the other damage. Clean the aproval plate of the engine. inside of the guard before Never use a cutting blade with fitting a new blade. -
Page 11: What Is What
WHAT IS WHAT? What is what on a power cutter? 1 Operator’s manual 12 Front handle 2 Decompression valve 13 Air filter cover 3 Water valve 14 Choke 15 Stop switch 4 Adjustment handle for blade guard 5 Blade guard 16 Throttle trigger lockout 6 Throttle control 17 Starter... -
Page 12: Assembly
Do not use different size flanges.. Fitting the cutting blade Partner cutting blades are manufactured and approved for freehand cutting. The paper labels on each side of the blade are there to distribute the pressure from the flange washer and prevent the blade from slipping. -
Page 13: Fuel Handling
Mixing ratio 1:50 (2%). • If PARTNER two-stroke oil is not available, you may use another two-stroke oil • Always exercise care when of good quality that is filling the fuel. Move the... -
Page 14: Start And Stop
START AND STOP Start and stop Start WARNING! Before starting observe the WARNING! The cutting blade can rotate when following: the engine starts. Make sure it can rotate freely. • Do not start the power cutter without the cutting arm, Take hold of the front handle belt or cutting head fitted. -
Page 15: Maintenance
Carburettor with fixed jets unscrew the screws (A) that secure the cutting head and Your Partner product has been designed and manufactured to belt guard 1/2 a turn. specifications that reduce harmful emissions. After your unit has been run 8-10 tanks of fuel the engine has broken in. -
Page 16: Fuel/Air Filter
Water filter inspected/replaced regularly or cleaned and oiled. A Check and clean the filter as special PARTNER oil has necessary. been produced for this purpose. • Remove the filter. Wash the filter carefully in tepid, soapy water. -
Page 17: Starter
MAINTENANCE Starter Tensioning the recoil spring • Lift up the starter cord from WARNING! the cut out on the pulley and • The recoil spring sits in its tensioned posi turn the pulley approx. 2 tion in the starter housing and can with turns clockwise. -
Page 18: Spark Plug
MAINTENANCE Spark plug Cooling system The condition of the spark plug To obtain the lowest possible running temperature the power is affected by: cutter is equipped with a cooling system. • An incorrect carburettor setting. The cooling system consists 0,5 mm •... -
Page 19: Daily Maintenance
MAINTENANCE Below follows some general maintenance instructions. If you need further information please contact your service workshop. Daily maintenance Check that throttle components work correctly from a safety view point (throttle and starter throttle catch). Clean the outside of the power cutter.. Check the tension of the drive belt. -
Page 20: Technical Data
TECHNICAL DATA K650 Active III K700 Active III Engine Cylinder volume, cm cu.in Cylinder bore, mm/inch Ø 50 Ø 50 Stroke, mm/inch Idle speed, rpm 2 500 2 500 Recommended max. speed, unloaded, rpm 9 750 ± 250 9 750 ± 250... - Page 21 We, Partner Industrial Products, S-433 81 Partille, Sweden, tel: +46-31949000, declare under sole responsibility that the power cutters Partner K650 Active III / K700 Active III from 2002’s serial numbers and onwards (the year is clearly stated in plain text on the type plate with subsequent serial number), are in conformity with the following standards or other normative documents following the provisions in the COUNCIL’S DIRECTIVES:...
- Page 22 ´*xrh¶6/¨ – English...
- Page 23 English –...
- Page 24 108 88 27-26 ´*xrh¶6/¨ 2002W03...
Need help?
Do you have a question about the K650 ACTIVE III and is the answer not in the manual?
Questions and answers