1. Manuals
  2. Brands
  3. Partner Manuals
  4. Cutter
  5. K950 Active
  6. Operator's manual

Partner K950 ACTIVE Operator's Manual

Hide thumbs Also See for K950 ACTIVE:
Table of Contents

Advertisement

Quick Links

Enlarged version

K950 ACTIVE

Operator's manual
Read these instructions carefully and
make sure you understand them
before using the machine.

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the K950 ACTIVE and is the answer not in the manual?

Questions and answers

Subscribe to Our Youtube Channel

Related Manuals for Partner K950 ACTIVE

Summary of Contents for Partner K950 ACTIVE

  • Page 1: K950 Active

    K950 ACTIVE Operator’s manual Read these instructions carefully and make sure you understand them before using the machine.

  • Page 2: Symbol Explanation

    SYMBOL EXPLANATION Symbols on the power cutter: Symbols in the Operator's Manual: WARNING! The power cutter can be Switch off the engine by moving the stop dangerous! Careless and incorrect use can switch to the STOP position before result in serious or fatal injury to the carrying out any checks or maintenance.

  • Page 3: Table Of Contents

    Transport and storage ............6 adjusted! • Let your Partner dealer check the power cutter and carry out Fuel safety ................7 essential adjustments and repairs. General working instructions ...........

  • Page 4: Safety Instructions

    SAFETY INSTRUCTIONS THE POWER CUTTER’S SAFETY WARNING! Incorrect or careless use of a EQUIPMENT power cutter can turn it into a dangerous tool that can cause serious or even fatal injury. It This section describes the power cutter’s safety equipment, its is extremely important that you read and function and how checks and maintenance are carried out to understand this manual.

  • Page 5: Control, Maintenance And Service Of The Machine's Safety Equipment

    SAFETY INSTRUCTIONS 3 Muffler Control, maintenance and service of the machine‘s safety equipment WARNING! During use and for some time after the muffler is very hot. Do not touch the WARNING! All service and repairs to the muffler if it is hot! power cutter require special training.

  • Page 6: General Safety Instructions

    SAFETY INSTRUCTIONS 3 Muffler GENERAL SAFETY INSTRUCTIONS Never use a machine that has a defective muffler. IMPORTANT INFORMATION! Do not use the power cutter until you have read the entire contents of this Operator’s Manual. All servicing, in addition to the points listed in the section ”...

  • Page 7: Fuel Safety

    • Some working positions may create greater stress on the operator. • Use a Partner fuel can with an anti-spill device. • Check the cutting area for buried cables and wires. WARNING! Use a Partner fuel can with an Only use the machine in areas with good anti-spill device.

  • Page 8: Kickback

    SAFETY INSTRUCTIONS Water cooling Over exposure to vibrations can result in blood-vessel or nerve injury to persons WARNING! Water cooling, which is only used suffering with blood circulation problems. for petrol-driven power cutters and when Seek medical attention if you experience cutting concrete, cools the cutting blade and physical symptoms that can be related to over increases its service life as well as reduce...

  • Page 9: Care And Storage

    (To avoid this see the section General ” How to avoid kickback ” and ”Pinching/rotation” below). Partner’s power cutters are robust and durable. However, as Pinching/rotation they are used for high speed operations all servicing should be Pinching occurs when the cut closes.

  • Page 10: Cutting Blades

    Increases the Con- High speed portable tools usage, crete asphalt, blade’s service Cutting blades of the make Partner are manufactured for economical stone, life. Reduces portable, high speed, power cutters. If other makes of cutting brickwork, dust formation. blades are used, ensure the blades comply with all the cast iron, Recommended.

  • Page 11: Diamond Blades

    SAFETY INSTRUCTIONS Type of cutting blades Guard Check that the blade is Check that the guard is not approved for the same or cracked or shows signs of any higher speed according to the other damage. Clean the aproval plate of the engine. inside of the guard before Do not exceed the maximum fitting a new blade.

  • Page 12: What Is What

    WHAT IS WHAT? What is what on a power cutter? Cylinder cover 12. Throttle control Muffler 13. Combination spanner Fuel tank 14. Air filter cover Starter throttle catch 15. Blade guard Choke 16. Starter handle Throttle trigger lockout 17. Operator’s manual Stop switch 18.

  • Page 13: Assembly

    ASSEMBLY Fitting the cutting head Fitting the cutting blade Remove the bolts (1). Remove Partner cutting blades are the cover. Fit the drive belt manufactured and approved over the clutch drum. Refit the for freehand cutting. The cover and tighten the bolts.

  • Page 14: Fuel Handling

    Mixing ratio 1:50 (2%). Gasolin Oil • Öl • If PARTNER two-stroke oil Benzin Huile • Aceite Essence Lit. is not available, you may Gasolina 2%(1:50) 3%(1:33) 4%(1:25) Lit.

  • Page 15: Start And Stop

    START AND STOP Start and stop Start WARNING! Before starting observe the WARNING! The cutting blade can rotate when following: the engine starts. Make sure it can rotate freely. • Do not start the power cutter without the cutting arm or Take hold of the front handle cutting head fitted.

  • Page 16: Maintenance

    MAINTENANCE Belt pulley and clutch Adjusting the drive belt Never start the engine when the belt pulley and clutch are • The drive belt is fully removed for maintenance. enclosed and well protected from dust, dirt and mechanical effects during the cutting process.

  • Page 17: Carburettor

    MAINTENANCE Carburettor Carburettor Your Partner product has been designed and manufactured to specifications that reduce harmful emissions. After your unit has been run 8-10 tanks of fuel the engine has broken in. To ensure that your unit is at peak performance and...

  • Page 18: Fuel Filter

    The filter must be cleaned and oiled regularly to obtain a satisfactory filtering effect. There is a special PARTNER oil produced for this purpose. • Remove the filter. Wash the filter carefully in tepid, soapy water. After cleaning rinse the filter thoroughly in clean water.

  • Page 19: Starter

    MAINTENANCE Starter Tensioning the recoil spring • Lift up the starter cord from WARNING! the cut out on the pulley and • The recoil spring sits in its tensioned posi- turn the pulley approx. 2 tion in the starter housing and can with turns clockwise.

  • Page 20: Spark Plug

    MAINTENANCE Spark plug Cooling system The condition of the spark plug To maintain as low an operating temperature as possible the is affected by: power cutter is equipped with a cooling system. • An incorrect carburettor setting. The cooling system consists •...

  • Page 21: Daily Maintenance

    MAINTENANCE Below follows some general maintenance instructions. If you need further information please contact your service workshop. Daily maintenance 1. Check that throttle components work correctly from a safety view point (throttle and starter throttle catch). 2. Clean the main filter. 3.

  • Page 22: Technical Data

    We, Partner Industrial Products, S-433 81 Partille, Sweden, tel. +46-31-949000, declare under sole responsibility that the power cutter Partner K950 Active from the serial numbers of 1998 and onwards (the year is clearly stated in plain text on the type plate with subsequent serial number), is in conformity with the following standards or other normative documents following the provisions in the COUNCIL’S DIRECTIVES:...
  • Page 23 English –...
  • Page 24 108 88 00-26 ´*xp"¶6F¨ 2000W37...

Table of Contents

Save PDF