Related Manuals for Partner K950 RING
Summary of Contents for Partner K950 RING
-
Page 1: K950 Ring
K950 RING Operator’s manual Read these instructions carefully and make sure you understand them before using the machine. -
Page 2: Symbol Explanation
1 Wooden carrying case 1 Tool kit 1 Operator’s manual 1 Illustrated parts list The Partner K950 ring power cutter a hand-held power cutter that cuts 260 mm (10") with a 350 mm (14") blade. This design is exclusive to Partner Industrial Products, and is another example of Partner’s continuous... -
Page 3: Table Of Contents
Transport and storage ............6 adjusted! • Let your Partner dealer check the power cutter and carry out Fuel safety ................7 essential adjustments and repairs. General working instructions ........... -
Page 4: Safety Instructions
SAFETY INSTRUCTIONS THE POWER CUTTER’S SAFETY WARNING! Incorrect or careless use of a EQUIPMENT power cutter can turn it into a dangerous tool that can cause serious or even fatal injury. It This section describes the power cutter’s safety equipment, its is extremely important that you read and function and how checks and maintenance are carried out to understand this manual. -
Page 5: Control, Maintenance And Service Of The Machine's Safety Equipment
SAFETY INSTRUCTIONS 3 Muffler Control, maintenance and service of the machine‘s safety equipment WARNING! During use and for some time after the muffler is very hot. Do not touch the WARNING! All service and repairs to the muffler if it is hot! power cutter require special training. -
Page 6: General Safety Instructions
SAFETY INSTRUCTIONS 5 Blade guard for the cutting blade 3 Muffler Never use a defective blade Never use a machine that has guard or a blade guard that is a defective muffler. not fitted correctly. Check regularly that the muffler is secured to the engine body. -
Page 7: Fuel Safety
Only use the machine in areas with good ventilation. Neglect can result in serious • Use a Partner fuel can with an anti-spill device. injury or death. Carbon monoxide in the exhaust fumes causes suffocation. -
Page 8: Kickback
SAFETY INSTRUCTIONS Kickback Over exposure to vibrations can result in blood-vessel or nerve injury to persons WARNING! suffering with blood circulation problems. Kickback can occur very suddenly and with Seek medical attention if you experience great force. If the following directives are not physical symptoms that can be related to over followed, it can result in serious or even fatal exposure to vibrations. -
Page 9: Care And Storage
Partner’s power cutters are robust and durable. However, as they are used for high speed operations all servicing should be carried out on time and as specified, so that the power cutter Sharpening diamond blades always works effectively and safely. -
Page 10: What Is What
WHAT IS WHAT? 12 11 What is what on a power cutter? Engagement rollers 15. Support cover screws Support rollers 16. Roller adjustment screws Drive disc 17. Decompression valve Lock nuts for support rollers 18. Air filter cover Water flow adjustment valve 19. -
Page 11: Set Up And Adjustments
SET UP AND ADJUSTMENTS Drive Principle Essential Service As the blade is used, the The machine’s unique design allows the blade to be driven by a DRIVE DISC inner diameter of the blade, belt driven shaft mounted off the center of the blade. This as well as the groove in the feature provides a total cutting depth of 260 mm (10 inches) drive disc, will wear. -
Page 12: Blade Installation
NOTE: Partner offers a selection of wet cutting ring blades for different materials. Check with a Partner dealer for the blade that is best suited for your application. WARNING! Never retip a used ring blade. A used blade •... - Page 13 SET UP AND ADJUSTMENTS • Tighten the lock nuts on the WARNING! support roller cover. Inspect the blade for damage before installing on the unit. Damaged blades can break and cause severe injury. • Assemble the support roller cover and make sure that blade groove is aligned with both engagement rollers.
-
Page 14: Removal Of Engagement Roller Compl
SET UP AND ADJUSTMENTS Removal of engagement roller compl. Installation of engagement roller compl. • Remove the knob. • Apply grease in the housing, then push in the engagement rollers in the housing. • The engagement roller compl. can now be pulled out from the •... -
Page 15: Drive Disc
SET UP AND ADJUSTMENTS IMPORTANT NOTES: Support Rollers/Engagement Rollers • The support rollers do not • Remove the support drive the blade. roller cover. • Improper adjustment can • Check the condition of all lead to blade damage. the rollers •... -
Page 16: Fuel Handling
Mixing ratio 1:50 (2%). Gasolin Oil • Öl Benzin • If PARTNER two-stroke oil Huile • Aceite Essence Lit. is not available, you may Gasolina 2%(1:50) 3%(1:33) 4%(1:25) Lit. -
Page 17: Start And Stop
START AND STOP Start and stop Start WARNING! Before starting observe the WARNING! The cutting blade can rotate when following: the engine starts. Make sure it can rotate freely. • Do not start the power cutter without the Take hold of the front handle cutting arm or cutting head fitted. -
Page 18: Maintenance
MAINTENANCE Adjusting the drive belt Carburetor Your Partner product has been designed and manufactured to • The drive belt is fully specifications that reduce harmful emissions. enclosed and well protected from dust, dirt and mechanical effects during the cutting process. -
Page 19: Fuel Filter
• The filter must be replaced or cleaned and oiled regularly to obtain a satisfactory filtering effect. Use a Partner Foam filter oil for re-oiling. • Remove the filter. Wash the filter carefully in tepid, soapy water. After cleaning rinse the filter thoroughly in clean water. -
Page 20: Starter
MAINTENANCE Starter Tensioning the recoil spring WARNING! • Lift up the starter cord from • The recoil spring sits in its tensioned posi the cut out on the pulley and tion in the starter housing and can with turn the pulley approx. careless handling fly out and cause personal 7 turns clockwise. -
Page 21: Spark Plug
A broken blade may cause serious personal injury to the operator or others. For this reason, Partner will not authorize a ring blade to be totally retipped. A single segment may sometimes be retipped. -
Page 22: Daily Maintenance
MAINTENANCE Below follows some general maintenance instructions. If you need further information please contact your service workshop. Daily maintenance 1. Check that throttle components work correctly from a safety view point (throttle and starter throttle catch). 2. Check engagement roller wear daily. 3. -
Page 23: Technical Data
TECHNICAL DATA K950 Ring Engine Cylinder volume, cm cu.in 93,6/5,7 ∅ 56/2,2" Cylinder bore, mm/inch Stroke, mm/inch 38/1,5" Idle speed, rpm 2 500 rpm Recommended max. speed, unloaded, rpm 9 800 ± 300 Power, kW Ignition system Manufacturer Type of ignition system... -
Page 24: Troubleshooting
Partner Industrial Products, SE-433 81 Partille, Sweden, tel. +46-31-949000, declare under sole responsibility that the power cutter Partner K950 Ring from the serial numbers of 2002 and onwards (the year is clearly stated in plain text on the type plate with subsequent serial number), are in conformity with the following standards or other normative documents following the provisions in the COUNCIL’S DIRECTIVES:... - Page 26 ´®z*xw@¶6&¨...
- Page 27 English –...
- Page 28 108 88 73-26 ´®z*xw@¶6&¨ 2003W06...