Sharp AY-ZP35PR Service Manual page 19

AY-ZP35PR
3.3.1 Details of troubleshooting procedure for PAM
1) PAM shutdown due to error
 :KHQ WKH '& YROWDJH GHWHFWLRQ FLUFXLW VHQGV D VLJQDO H[FHHGLQJ WKH VSHFL¿HG YROWDJH WR WKH PLFURFRPSXWHU
DC voltage of 350 V or higher (detection circuit input voltage of about 9.2 V or higher) [IC8 pin (4)]
–When an error is detected
‡ 3$0 ,*%7 WXUQV 2))
‡ &RPSUHVVRU WXUQV 2))
‡ $OO XQLWV VKXW GRZQ FRPSOHWHO\ ZKHQ WKH HUURU RFFXUV IRXU WLPHV
 :KHQ WKH RXWGRRU XQLW FORFN ZDYHIRUP GLIIHUV IURP WKH VSHFL¿HG YDOXH LPPHGLDWHO\ EHIRUH WKH 3$0 ,*%7 WXUQV 21
:KHQ WKHUH LV QR FORFN ZDYHIRUP LQSXW:KHQ D FORFN VLJQDO RI RWKHU WKDQ VSHFL¿HG SRZHU VRXUFH IUHTXHQF\  +] LV LQSXW
–When an error is detected
‡ 3$0 ,*%7 GRHV QRW WXUQ 21
‡ &RPSUHVVRU RSHUDWHV QRUPDOO\
‡ &RPSOHWH VKXWGRZQ GRHV QRW RFFXU
2) PAM error indication
In case of error "1)"
– An error signal is sent to the indoor unit as soon as an error is generated.
‡ 0DOIXQFWLRQ 1R  LV LQGLFDWHG ZKHQ WKH HUURU FRGH LV FDOOHG RXW E\ WKH LQGRRU XQLW V VHOIGLDJQRVLV IXQFWLRQ
± 7KH /(' RQ WKH RXWGRRU XQLW ÀDVKHV  WLPHV ZKHQ DQ HUURU LV JHQHUDWHG
‡ 7KH /(' FRQWLQXHV ÀDVKLQJ LQ WKH WLPH F\FOH HYHQ DIWHU WKH FRPSUHVVRU VWRSV RSHUDWLQJ
‡ 7KH /(' WXUQV RII GDWD LV GHOHWHG IURP WKH PHPRU\ ZKHQ WKH RXWGRRU XQLW SRZHU LV WXUQHG RII
In case of error "2)"
– An error signal is sent to the indoor unit as soon as an error is judged.
‡ 0DOIXQFWLRQ 1R  LV LQGLFDWHG ZKHQ WKH HUURU FRGH LV FDOOHG RXW E\ WKH LQGRRU XQLW V VHOIGLDJQRVLV IXQFWLRQ
± 7KH /(' RQ WKH RXWGRRU XQLW ÀDVKHV  WLPHV ZKHQ DQ HUURU LV MXGJHG
‡ 7KH /(' RQ WKH RXWGRRU XQLW ÀDVKHV LQ QRUPDO SDWWHUQ ZKHQ WKH FRPSUHVVRU VWRSV RSHUDWLQJ
(Compressor OFF or Thermostat OFF from remote control)
:KHQ D XVHU FRPSODLQV WKDW WKH DLUDLU KHDW SXPS GRHV QRW SURYLGH VXI¿FLHQW FRRO DLU RU ZDUP DLU
In addition to conventional error-generating reasons, there is a possibility that the PAM IGBT does not turn ON even if the com-
pressor is operating.
In that case, the DC voltage does not rise even though the compressor is operating, and lowers to the 180-VDC level.
–Check items
‡ &ORFN FLUFXLW FKHFN
‡ 3$0 ,*%7 FKHFN
‡ )XVH )X RSHQFLUFXLW FKHFN
4. Explanation of IPM drive circuit
The IPM for compressor drive is made by Mitsubishi Electric.
The power supply for the IPM drive, the shunt resistance for over current detection, etc., are provided outside the IPM (control PCB).
4.1. IPM drive power supply circuit
The power supply for the upper-phase IGBT (HU, HV, HW) drive employs a bootstrap system, and provides power to the upper-phase
IC.
The 15-V power supply for the lower-phase IC is provided by the control printed circuit board (PCB).
4.1.1 Brief explanation of bootstrap system (single power drive system)
To supply power to the upper-phase IC, the microcomputer (IC1) turns ON the lower-phase IGBT (LU, LV, LW).
7KLV UHVXOWV LQ D FKDUJLQJ FXUUHQW WKDW ÀRZV WR WKH HOHFWURO\WLF FDSDFLWRU RI HDFK XSSHUSKDVH ,& LQSXW DQG FKDUJHV WKH ERRWVWUDS FDSDFL-
tor with a 15V current.
2-14