Operation And Adjustment - Healthrider HETL09900 User Manual

TROUBLE-SHOOTING AND MAINTENANCE
Most treadmill problems can be solved by following the instructions below.f further assistance is needed,
please call our Customer Service Department at 0345-089009.
PROBLEM SOLUTION
1. The power does not a. Make sure that the power cord is plugged into a properly earthed outlet. (See
turn on HOW TO PLUG IN THE POWER CORD on page 8.) If an extension cord is
needed, use only a 3-conductor, 14-gauge (1mm
meters (5 feet). Important: The treadmill is not compatible with GFCI-equipped
outlets.
` b. Make sure that the key is fully inserted into the console.
c. Check the circuit breaker located on the frame near
the power cord. If the switch protrudes as shown, the
circuit breaker has tripped. To reset the circuit
breaker, wait for five minutes and then press the
switch back in.
d. Check the on/off switch located on the frame near
the power cord. The switch must be in the on posi-
tion.
2. The power turns off a. Check the circuit breaker located on the treadmill frame near the power cord (see
during use 1. c. above). If the circuit breaker has tripped, wait for five minutes and then press
the switch back in.
b. Make sure that the power cord is plugged in.
c. Remove the key from the console and then reinsert it.
d. Make sure that the on/off switch is in the on position (see 1. d. above).
3. The walking belt a. Make sure that only an appropriate surge protector is used (see 1. a. above).
slows when walked
on b. If the walking belt is overtightened,
treadmill performance may decrease and
the walking belt may be permanently
damaged. Remove the key and UN-
PLUG THE POWER CORD. Using the
included allen wrench, turn both rear
roller adjustment bolts counterclockwise
1/4 of a turn. When the walking belt is
properly tightened, you should be able to
lift the edges of the walking belt 7 to 10
cm off the walking platform. Be careful to
keep the walking belt centered. Plug in
the power cord, insert the key and run the treadmill for a few minutes. Repeat until
the walking belt is properly tightened.
22
2 ) cord that is no longer than 1.5
Tripped Reset
T i d Reset
On
Position
b
7Ð10 cm
Rear Roller Adjustment Bolts

OPERATION AND ADJUSTMENT

THE PERFORMANT LUBE TM WALKING BELT
Your treadmill features a walking belt coated with PERFORMANT LUBE
TANT: Never apply silicone spray or other substances to the walking belt or the walking platform. They will
deteriorate the walking belt and cause excessive wear.
HOW TO PLUG IN THE POWER CORD
This product must be earthed. If it should malfunction or break
down, earthing provides a path of least resistance for electric cur-
rent to reduce the risk of electric shock. This product is equipped
with a cord having an equipment-earthing conductor and a earth-
ing plug.
Two power cords are included. Select the one that will fit your
outlet. Refer to drawing 1. Plug the indicated end of the
power cord into the socket on the treadmill. Refer to drawing
2. Plug the power cord into an appropriate outlet that is prop-
erly installed and earthed in accordance with all local codes
and ordinances. Note: In Italy, an adaptor (not included) must
be used between the power cord and the outlet. Important: The
treadmill is not compatible with GFCI-equipped outlets.
DANGER:
Improper connection of the
equipment-earthing conductor can result in an in-
creased risk of electric shock. Check with a qualified
electrician or serviceman if you are in doubt as to
whether the product is properly earthed. Do not mod-
ify the plug provided with the productÑif it will not fit
the outlet, have a proper outlet installed by a qualified
electrician.
TM , a high-performance lubricant. IMPOR-
1
Socket on treadmill
2
Outlet
7