Healthrider HETL09900 User Manual page 6

ASSEMBLY
Assembly requires two people. Place the treadmill in a cleared area and remove all packing materials. Do not
dispose of the packing materials until the treadmill is assembled. No tools are required.
Note: The underside of the treadmill walking belt is coated with high-performance lubricant. During shipping, a
small amount of lubricant may be transferred to the top of the walking belt, the sides of the walking platform, or
the shipping carton. This does not affect treadmill performance. If there is lubricant on top of the walking belt or
on the sides of the walking platform, wipe off the lubricant with a soft cloth and a mild, non-abrasive cleaner.
If you have additional questions, please call our our Customer Service Department at 0345-089009.
1. With the help of a second person, carefully raise the
Uprights (103) until the Base Wheels (99) are resting on
the floor as shown.
2. Next, make sure that the Lock Knob Sleeve (68) is fully
inserted into the left Upright (103).
Remove the Lock Knob (67) from the Lock Pin (72). Make
sure that the Lock Pin Collar (70) and the Lock Spring
(69) are on the Lock Pin. Insert the Lock Pin into the left
Upright (103) and tighten the Lock Knob onto it.
3. Make sure that all parts are tightened before you use the treadmill. Place a mat beneath the treadmill
to protect the floor or carpet. For your benefit, we recommend that you familiarise yourself with the
TROUBLE-SHOOTING AND MAINTENANCE section on pages 22 and 23.
6
1
103
99
2
103
69
70
72
68
67
PROBLEM SOLUTION
4. The walking belt is a. If the walking belt has shifted to the
off-centre or slips left, first remove the key and UNPLUG
when walked on THE POWER CORD. Using the allen
wrench, turn the left rear roller adjustment
bolt clockwise, and the right bolt counter-
clockwise, 1/4 of a turn each. Be careful
not to overtighten the walking belt. Plug in
the power cord, insert the key and run the
treadmill for a few minutes. Repeat until the walking belt is centered.
b. If the walking belt has shifted to the
right, first remove the key and UNPLUG
THE POWER CORD. Using the allen
wrench, turn the left rear roller adjustment
bolt counterclockwise, and the right bolt
clockwise, 1/4 of a turn each. Be careful
not to overtighten the walking belt. Plug in
the power cord, insert the key and run the
treadmill for a few minutes. Repeat until the walking belt is centered.
c. If the walking belt slips when walked
on, first remove the key and UNPLUG
THE POWER CORD. Using the allen
wrench, turn both rear roller adjustment
bolts clockwise, 1/4 of a turn. When the
walking belt is correctly tightened, you
should be able to lift the edges of the
walking belt 7 to 10 cm off the walking
platform. Be careful to keep the walking belt centered. Plug in the power cord, in-
sert the key and run the treadmill for a few minutes. Repeat until the walking belt
is properly tightened.
5. The displays of the a. Remove the key from the console and UN-
console do not func-
PLUG THE POWER CORD. Next, remove
tion properly the screws from the hood and carefully re-
move the hood. Locate the Reed Switch
(26) and the Magnet (85) on the left side of
the Pulley (28). Turn the Pulley until the
Magnet is aligned with the Reed Switch.
Make sure that the gap between the
Magnet and the Reed Switch is about
3 mm. If necessary, loosen the Reed
Switch Screw (2) and move the Reed Switch slightly. Retighten the Screw. Re-at-
tach the hood, and run the treadmill for a few minutes to check for a correct speed
reading.
6. Bubbles form in the a. Due to variations in humidity and temperature, there is a possibility that
walking belt bubbles may form in the walking belt. Although the bubbles will disappear with
time, you may unplug the power cord, carefully insert a needle into the bubbles,
and push the air out of the bubbles.
a
b
c
3 mm
28
2
85
26
Top
View
23