Using The On-Screen Menus; Selecting The Source To Play; Selecting Different Sources For Picture And Sound; Activating The Dsp Modes - JVC RX-888VBK Instructions Manual

You can use the Menus on the TV screen to control the receiver.
To use this function, you need to connect the TV to the MONITOR OUT jack on the rear panel (see page 7), and set the
TV's input mode to the proper position to which the receiver is connected.
• When the TV's input mode is incorrect; for example, a different video input or TV tuner mode is selected, you
cannot show the Menus on the TV screen.
On-Screen Operation buttons (on the remote control)
STANDBY ON
TV/CATV/DBS VCR 1
POWER POWER
DVD DVD MUILTI CD TAPE/MD
TV/DBS VIDEO PHONO FM/AM
VCR 1 VCR 2 ANALOG/DIGITAL SLEEP
SURROUND CNTR TONE CNTR
1 2 3
ON/OFF
MENU MENU
TEST REAR-L
SURROUND
4 5 6
MODE
ENTER ENTER
DISC
EFFECT REAR-R
7 8 9
/P
SOUND SEA MODE SUBWOOFER
10 0 +10
100+
RETURN FM MODE/MUTING
AUDIO/
TV/VCR
MENU
CATV/DBS
SET
TEXT
EXIT
DISPLAY
TV VOL CHANNEL VOLUME
TV/VIDEO VCR 1 TAPE MUTING
CONTROL
/REW PLAY
FF/
DOWN TUNING UP
REC STOP PAUSE
RM-SRX888J REMOTE CONTROL
Selecting the Source to Play (Also see page 9)
1. Press MENU.
The MAIN MENU appears on the TV.
• Pressing one of the % / fi / @ / # buttons also displays the
MAIN MENU.
MAIN MENU
SOURCE :ch 1 FM 87.5 MHz
VISUAL :VCR1
MODE :OFF
SOUND CONTROL
TUNER CONTROL
SETTING
:OPERATE
VOLUME : 20
Note:
The on-screen display will disappear if no operation is done for
about 1 minute.
2. Press % / fi to move
3. Press @ / # to select the source.
4. When you finish, press EXIT.
The menu disappears from the TV.
MENU
SET
EXIT
Shows the buttons you
can use on the current
menu.
In this case, use % / fi to
move up and down,
and @ / # to select,
adjust or set the item.
to "SOURCE."
Selecting Different Sources for Picture and
Sound (Also see page 10)
1. Press MENU.
The MAIN MENU appears on the TV.
• Pressing one of the % / fi / @ / # buttons also displays the
MAIN MENU.
2. Press % / fi to move
to "VISUAL."
3. Press @ / # to select a
different video source.
4. When you finish, press EXIT.
The menu disappears from the TV.
Activating the DSP Modes (Also see page 27)
1. Press MENU.
The MAIN MENU appears on the TV.
• Pressing one of the % / fi / @ / # buttons also displays the
MAIN MENU.
2. Press % / fi to move
to "MODE."
3. Press @ / # to select the
DSP mode you want to
use.
4. When you finish, press EXIT.
The menu disappears from the TV.

Adjusting the Front Speaker Output Balance

(Also see page 12)
1. Press MENU.
The MAIN MENU appears on the TV.
• Pressing one of the % / fi / @ / # buttons also displays the
MAIN MENU.
2. Press % / fi to move
CONTROL," then press @ / #.
The SOUND CONTROL menu appears.
3. Press % / fi to move
to "BAL." (Balance).
4. Press @ / # to adjust
the balance.
5. When you finish, press EXIT repeatedly until the
menu disappears from the TV.
MAIN MENU
SOURCE :PHONO
VISUAL :VCR1
MODE :OFF
SOUND CONTROL
TUNER CONTROL
SETTING
:OPERATE
VOLUME : 20
MAIN MENU
SOURCE :VCR1
VISUAL :VCR1
MODE :PRO LOGIC
SOUND CONTROL
TUNER CONTROL
SETTING
:OPERATE
VOLUME : 20
to "SOUND
SOUND CONTROL
SURROUND LEVEL
SEA
BAL.:R-21
LOUDNESS : OFF
INPUT ATT : NORMAL
SUBWFR LEVEL: 0dB
NEXT PAGE
:OPERATE