Cisco TelePresence Codec C90 Administrator's Manual page 69

Cisco TelePresence System Codec C90 and Profile 65" Dual using C90
Contents Introduction
Experimental Audio Panning MonitorRight
NOTE: This Experimental command can be used 'as is' and will not be further documented. The
Experimental settings WILL change.
Requires user role: ADMIN
Value space: <1/2/3/4/5>
Example: Experimental Audio Panning MonitorRight: 1
Experimental AudioTracking Camera [1..7] Mode
NOTE: This Experimental command can be used 'as is' and will not be further documented. The
Experimental settings WILL change.
Requires user role: ADMIN
Value space: <On/Off>
Example: Experimental AudioTracking Camera 1 Mode: Off
Experimental BrightnessGradient Camera [1..7] Mode
NOTE: Applies to Cisco TelePresence T1/T3. The Experimental settings can be used 'as is' and
will not be further documented. NOTE: The Experimental settings WILL change.
This settings can be configured from the command line interface, and not from the menu.
Requires user role: ADMIN
Value space: <On/Off>
On: Enable row dependent digital gain.
Off: Disable row dependent digital gain.
Example: Experimental BrightnessGradient Camera 1 Mode: Off
Experimental BrightnessGradient Camera [1..7] Level
The Experimental settings can be used 'as is' and will not be further documented. NOTE: The
Experimental settings WILL change.
NOTE: Applies to Cisco TelePresence T1/T3. This settings can be configured from the command
line interface, and not from the menu. Set the camera brightness gradient level to control the
row dependent digital gain for the top row of the image. The gain gradient is applied so that
intermediate rows have gains that are determined by linear interpolation of the top row gain and
the gain for the bottom row. A gain of 1.0x is always applied to the bottom row of the image.
Requires user role: ADMIN
Value space: <10..39>
Range: The range 10 to 39 corresponds to gains in the range 1.0x to 3.9x.
Example: Experimental BrightnessGradient Camera 1 Level: 10
D14635.0 6 Profile C90 and Codec C90 Administrator Guide TC4.2, July 2011.
Copyright © 2010-2011 Cisco Systems, Inc. All rights reserved.
Web interface Advanced settings Advanced settings
Experimental CapsetFilter
NOTE: This Experimental command can be used 'as is' and will not be further documented. The
Experimental settings WILL change.
Requires user role: ADMIN
Value space: <S: 0, 100>
Example: Experimental CapsetFilter: ""
Experimental CapsetReduction
NOTE: This Experimental command can be used 'as is' and will not be further documented. The
Experimental settings WILL change.
Requires user role: ADMIN
Value space: <Auto/Reduced>
Example: Experimental CapsetReduction: Auto
Experimental Conference [1..1] PacketLossResilience ForwardErrorCorrection
NOTE: This Experimental command can be used 'as is' and will not be further documented. The
Experimental settings WILL change.
Will enable ForwardErrorCorrection (RFC5109) mechanism as part of the PacketLossResilience
mechanism. Default value is On.
On: Forward error correction will be used as part of the PacketLossResilience mechanism.
Off: Forward error correction will NOT be used as part of the PacketLossResilience mechanism.
Requires user role: ADMIN
Value space: <On/Off>
Example: Experimental Conference 1 PacketLossResilience
ForwardErrorCorrection: On
Experimental Conference [1..1] PacketLossResilience RateAdaption
NOTE: This Experimental command can be used 'as is' and will not be further documented. The
Experimental settings WILL change.
Will use the a RateAdaption algorithm adapted to the PacketLossResilience mechanism. Default
value is On.
On: RateAdaption will be used as part of the PacketLossResilience mechanism.
Off: RateAdaption will NOT be used as part of the PacketLossResilience mechanism.
Requires user role: ADMIN
Value space: <On/Off>
Example: Experimental Conference 1 PacketLossResilience RateAdaption: On
69
Password protection Appendices
Administrator guide
Contact us
www.cisco.com