Cisco TelePresence Codec C90 Administrator's Manual page 65

Cisco TelePresence System Codec C90 and Profile 65" Dual using C90
Contents Introduction
Video OSD InputMethod Cyrillic
Set the Cyrillic mode for the menu input language in the menus on screen.
Requires user role: ADMIN
Value space: <On/Off>
On: Cyrillic mode is available as a menu input language in the menus on screen. This will
enable the setting xConfiguration Video OSD InputMethod InputLanguage.
Off: Cyrillic mode is NOT available as a menu input language in the menus on screen.
Example: Video OSD InputMethod Cyrillic: Off
Video OSD LoginRequired
Determine if the system should require the user to login before accessing the On Screen Display
(OSD). If enabled, the user must enter his username and his PIN. After the user has logged in he
can only execute to the configurations changes and commands allowed by his Role.
Requires user role: ADMIN
Value space: <On/Off>
On: The user must log in to access the On Screen Display (OSD).
Off: No login to the OSD is required.
Example: Video OSD LoginRequired: Off
Video AllowWebSnapshots
Set if the system shall be allowed to generate a web snapshot of the video input main source.
To generate and view the snapshot you must open a web browser, enter the IP address of the
codec, login to the Web interface, select Snapshot from the left menu, and press the button "Get
snapshot" .
NOTE: This is a local setting which is available only from the On Screen Display (OSD) and when
connected directly to the serial port (COM 1 port) on the codec.
Requires user role: ADMIN
Value space: <On/Off>
On: If set to on, a web snapshot can be generated and displayed on the web page under
"Snapshot" .
Off: The generation of web snapshots is not allowed.
Example: Video AllowWebSnapshots: Off
D14635.0 6 Profile C90 and Codec C90 Administrator Guide TC4.2, July 2011.
Copyright © 2010-2011 Cisco Systems, Inc. All rights reserved.
Web interface Advanced settings Advanced settings
Video Output HDMI [1, 3] CEC Mode
The HDMI outputs support Consumer Electronics Control (CEC). When set to on (default is off),
and the monitor connected to the HDMI output is CEC compatible and CEC is configured, the
system will use CEC to set the monitor in standby when the system enters standby. Likewise the
system will wake up the monitor when the system wakes up from standby. Please note that the
different manufacturers uses different marketing names for CEC: Anynet+ (Samsung); Aquos
Link (Sharp); BRAVIA Sync (Sony); HDMI-CEC (Hitachi); Kuro Link (Pioneer); CE-Link and Regza
Link (Toshiba); RIHD (Onkyo); SimpLink (LG); HDAVI Control, EZ-Sync, VIERA Link (Panasonic);
EasyLink (Philips); and NetCommand for HDMI (Mitsubishi).
Requires user role: ADMIN
Value space: <On/Off>
Example: Video Output HDMI 1 CEC Mode: Off
Video Output HDMI [1, 3] MonitorRole
The HDMI monitor role describes what video stream will be shown on the monitor connected to
the video output HDMI connector. Applicable only if the monitor configuration is set to dual or
quadruple.
Requires user role: ADMIN
Value space: <First/Second/PresentationOnly/Third/Fourth>
Example: Video Output HDMI 1 MonitorRole: First
Video Output HDMI [1, 3] OverscanLevel
Some TVs or other monitors may not display the whole image sent out on the systems video
output, but cuts the outer parts of the image. In this case this setting can be used to let the
system not use the outer parts of video resolution. Both the video and the OSD menu will be
scaled in this case.
Requires user role: ADMIN
Value space: <Medium/High/None>
Example: Video Output HDMI 1 OverscanLevel: None
65
Password protection
On: Enable CEC control.
Off: Disable CEC control.
First: Show main video stream.
Second: Show presentation video stream if active, or other participants.
PresentationOnly: Show presentation video stream if active, and nothing else.
Third: Use for remote participants (only for quadruple monitor setup).
Fourth: Use for remote participants (only for quadruple monitor setup).
Medium: The system will not use the outer 3% of the output resolution.
High: The system will not use the outer 6% of the output resolution
None: The system will use all of the output resolution.
Administrator guide
Appendices Contact us
www.cisco.com