Cisco TelePresence Codec C90 Administrator's Manual page 51

Cisco TelePresence System Codec C90 and Profile 65" Dual using C90
Contents Introduction
NetworkServices NTP Address
Enter the NTP Address to define the network time protocol server address. This address will be
used if NTP Mode is set to Manual, or if set to Auto and no address is supplied by a DHCP server.
Requires user role: ADMIN
Value space: <S: 0, 64>
Format: String with a maximum of 64 characters.
Example: NetworkServices NTP Address: "1.ntp.tandberg.com"
NetworkServices SIP Mode
Determine whether the system should be able to place and receive SIP calls or not. NOTE:
Requires a restart of the codec.
Requires user role: ADMIN
Value space: <On/Off>
On: Enable the possibility to place and receive SIP calls (default).
Off: Disable the possibility to place and receive SIP calls.
Example: NetworkServices SIP Mode: On
NetworkServices SNMP Mode
SNMP (Simple Network Management Protocol) is used in network management systems to
monitor network-attached devices (routers, servers, switches, projectors, etc) for conditions that
warrant administrative attention. SNMP exposes management data in the form of variables on the
managed systems, which describe the system configuration. These variables can then be queried
(set to ReadOnly) and sometimes set (set to ReadWrite) by managing applications.
Requires user role: ADMIN
Value space: <Off/ReadOnly/ReadWrite>
Off: Disable the SNMP network service.
ReadOnly: Enable the SNMP network service for queries only.
ReadWrite: Enable the SNMP network service for both queries and commands.
Example: NetworkServices SNMP Mode: ReadWrite
NetworkServices SNMP Host [1..3] Address
Enter the address of up to three SNMP Managers. All traps will then be sent to the hosts listed.
The system's SNMP Agent (in the codec) responds to requests from SNMP Managers (a PC
program etc.). SNMP Traps are generated by the SNMP Agent to inform the SNMP Manager
about important events. Can be used to send event created messages to the SNMP agent about
different events like: system reboot, system dialling, system disconnecting, MCU call, packet loss
etc. Traps can be sent to multiple SNMP Trap Hosts.
Requires user role: ADMIN
Value space: <S: 0, 64>
Format: String with a maximum of 64 characters.
Example: NetworkServices SNMP Host 1 Address: ""
D14635.0 6 Profile C90 and Codec C90 Administrator Guide TC4.2, July 2011.
Copyright © 2010-2011 Cisco Systems, Inc. All rights reserved.
Web interface Advanced settings Advanced settings
NetworkServices SNMP CommunityName
Enter the name of the Network Services SNMP Community. SNMP Community names are used
to authenticate SNMP requests. SNMP requests must have a password (case sensitive) in order
to receive a response from the SNMP Agent in the codec. The default password is "public" . If
you have the Cisco TelePresence Management Suite (TMS) you must make sure the same SNMP
Community is configured there too. NOTE: The SNMP Community password is case sensitive.
Requires user role: ADMIN
Value space: <S: 0, 50>
Example: NetworkServices SNMP CommunityName: "public"
NetworkServices SNMP SystemContact
Enter the name of the Network Services SNMP System Contact.
Requires user role: ADMIN
Value space: <S: 0, 50>
Example: NetworkServices SNMP SystemContact: ""
NetworkServices SNMP SystemLocation
Enter the name of the Network Services SNMP System Location.
Requires user role: ADMIN
Value space: <S: 0, 50>
Example: NetworkServices SNMP SystemLocation: ""
NetworkServices SSH Mode
SSH (or Secure Shell) protocol can provide secure encrypted communication between the codec
and your local computer.
Requires user role: ADMIN
Value space: <On/Off>
Example: NetworkServices SSH Mode: On
51
Password protection
Format: String with a maximum of 50 characters.
Format: String with a maximum of 50 characters.
Format: String with a maximum of 50 characters.
On: The SSH protocol is enabled.
Off: The SSH protocol is disabled.
Administrator guide
Appendices Contact us
www.cisco.com