DSC PowerSeries PK5500 Installation Instructions Manual
Hide thumbs
Also See for PowerSeries PK5500:
- Installation instructions manual (33 pages) ,
- User manual (28 pages) ,
- Instruction manual (20 pages)
Table of Contents
Advertisement
PK5500 v1.1 Installation Instructions
WARNING: Please refer to the System Installation Manual for information on limitations regarding product use
and function and information on the limitations as to liability of the manufacturer.
NOTE: These instructions shall be used in conjunction with the system Installation Manual of the Control Panel
with which this equipment is intended to be used.
1
2
3
4
5
6
7
8
9
*
0
#
2 9 0 0 7 4 9 6 R0 0 1
Advertisement
Table of Contents
Related Manuals for DSC PowerSeries PK5500
Summary of Contents for DSC PowerSeries PK5500
- Page 1 PK5500 v1.1 Installation Instructions WARNING: Please refer to the System Installation Manual for information on limitations regarding product use and function and information on the limitations as to liability of the manufacturer. NOTE: These instructions shall be used in conjunction with the system Installation Manual of the Control Panel with which this equipment is intended to be used.
-
Page 2: Mounting And Wiring
These keypads are compatible with the latest version of the unless mounting on a single gang box. folllowing DSC security systems: 2. Place keypad into hooks on the backplate and swing down to engage. 3. Run wire through wiring slot or knockouts. Connect Keybus and PGM/Zone •PC580... -
Page 3: Emergency Keys
Programming the Keypad Enter the following at each keypad installed on the system: Changing Brightness/Contrast 1. Enter Installer Programming by pressing [,][8][Installer’s Code] 1. Press [,][6][Master code]. There are several programming Toggle Option 2. Press [000] for Keypad Programming 2. Use the [<][>] keys to scroll to either Brightness Control or Contrast options available for the keypad. -
Page 4: Limited Warranty
Important Information: Changes or modifications not expressly approved by Digital Security Controls could void the user’s authority to operate this equipment. Printed in Canada © 2008 Digital Security Controls, Toronto, Canada • www.dsc.com Technical Support: 905-760-3036... -
Page 5: Keypad Enrollment
Keypad Enrollment Enter keypad programming by pressing [,][8][Installer’s Code][000]. [0] Partition / Slot Assignment Digit Option Valid Range Default Partition Assignment (0=Global Keypad) 0 to 8 I________I Slot Assignment 1 to 8 I________I [1]-[5] Function Key Assignment Function Key Button Valid Range Default Function... - Page 6 [065] Fire Alarm Label (28 Characters) Default:“Fire Zone” I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I [065] I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I [066] Fail to Arm Event Message Default: “System Has Failed to Arm” I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I [066] I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I [067] Alarm When Armed Event Message Default: “Alarm Occurred While Armed < >” I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I [067] I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I [071] First User Display Mask...
- Page 7 [074] Key Options Default Option [F]ire Key Enabled [F]ire Key Disabled I____I I____I For Future Use I____I [P]anic Key Enabled [P]anic Key Disabled For Future Use I____I [076] First Keypad Options Default Option Display Code when Programming Display “Xs” when Programming I____I Local Clock Display ON Local Clock Display OFF...
-
Page 8: Keypad Display Symbols
[120]-[151] Command Output Labels Default: “Command_O/ P_1” - “Command_O/P_4” For Partition 1 Command O/P 1 to 4 enter [120] to [123] For Partition 5 Command O/P 1 to 4 enter [136] to [139] For Partition 2 Command O/P 1 to 4 enter [124] to [127] For Partition 6 Command O/P 1 to 4 enter [140] to [143] For Partition 3 Command O/P 1 to 4 enter [128] to [131] For Partition 7 Command O/P 1 to 4 enter [144] to [147]...