Showing The Disc Information On The Tv Screen - JVC RX-8020VBK Instructions Manual

Operations:
To use this remote control system, you need to connect the TV to the
MONITOR OUT jack on the rear panel (see page 11), and set the
TV's input mode to the proper position to which the receiver is
connected. Make sure you have connected a CD player or
MD recorder equipped with the TEXT COMPU LINK
remote control system. If not, you cannot use the
following functions.
On-Screen Operating buttons (on the remote control)
A/V CONTROL RECEIVER
When you press TEXT DISPLAY,
"MENU" appears on the remote
display window.
CATV/DBS VCR1 TV AUDIO
DVD DVD MULTI CD FM/AM
TV/DBS VIDEO CDR PHONO
VCR1 VCR2 TAPE/MD USB
SURROUND DSP SURR/DSP ANALOG/DIGITAL
OFF INPUT
ANALOG BASS
∗ ∗
DIRECT BOOST FRONT•L FRONT•R
1 2 3
MENU
∗ ∗
SOUND TEST CENTER SUBWFR
4 5 6
ENTER
∗ ∗
DIMMER SURR•L SURR•R
8 9
7/P
∗ ∗ ∗
DIGITAL EQ SBACK•L SBACK•R
MUTING
TEXT
10 0 +10
RETURN FM MODE 100 +
DISPLAY
CATV/DBS
CONTROL
+ + +
∗
CH/ LEVEL TV VOL VOLUME
TV/VIDEO
− − −
TEXT
PLAY
DISPLAY MENU EXIT
REC /REW FF/
PAUSE
PAUSE
SET
DOWN – TUNING – UP
SLEEP
STOP CONTROL
RM-SRX8020J
REMOTE CONTROL
Showing the Disc Information on the TV
Screen
Press TEXT DISPLAY while "CD" or "MD" is
selected as the source.
The Disc Information screen appears on the TV.
45
PLAY
EXIT
MENU
/REW FF/
PAUSE
SET
DOWN – TUNING – UP
STOP
1 Source name: CD or MD
2 Select
or , then press SET to change the disc.
3 Track numbers and track titles.
• When you move
change the track information by pressing 2 or 3.
Each time you press the button, track information
alternates between its track title and its performer.
(You can also start playing the track by pressing SET.)
4 Select this (move
in front), then press SET to go to
the DISC SEARCH screen (see page 46).
5 Select this (move
in front), then press SET to go to
the TITLE INPUT screen (see page 47).
6 This appears only when a CD Text is selected.
7 Disc information such as the disc title, performer, and
music genre.
When this is selected (
disc information by pressing 2 or 3. Each time you
press the button, disc information (see "Note on 7")
changes.
8 Select
or , then press SET to change the track.
9 Usable buttons and their functions for the current
selection.
Indication here will be changed according to what is
currently selected ( in front) on the screen. See "Note
on 9."
Note on 7 :
The following information will appear on the display:
• For CD Texts—Disc title, Performer, Genre, Song writer, Composer,
Arranger, Message
Only recorded information will be shown. If there is no data, "NO
DATA" will appear.
• For MDs—Disc title
If there is no data, "NO DATA" will appear.
Note on 9 :
For example, the SET button will be used to start play (PLAY), to go to
the next screen (ENTER), and to determine the selection (ENTER).
To exit from the Disc information screen
Press EXIT.
Notes:
• The on-screen display will disappear in the following cases:
– if no operation is done for about 10 minutes.
– if you do any operation other than explained in this section.
• To control an MD recorder using the TEXT COMPU LINK remote
control system, you have to change the source name shown on the
display from "TAPE" to "MD." (See page 17.)
• Some special characters and marks cannot be displayed correctly.
to a track number, you can
in front), you can change the