Operating Video Components - JVC RX-8020VBK Instructions Manual

Operating Video Components

IMPORTANT:
To operate JVC's video components using this remote control:
• You need to connect JVC's video components through the AV
COMPU LINK jacks (see page 49) in addition to the connections
using cables with RCA pin plugs (see pages 10 to 12).
• Some JVC's VCRs can accept two types of the control signals—
remote code "A" and "B." Before using this remote control, make
sure that the remote control code of the VCR connected to the VCR 1
jacks is set to code "A."
– When another JVC's VCR is connected to the VCR 2 or VIDEO
terminals, set its remote control code to code "B." (This remote
control cannot emit the control signals of code "B.")
• When using the remote control, aim the remote control directly at
the remote sensor on each component, not on the receiver.
A/V CONTROL RECEIVER
CATV/DBS VCR1
DVD DVD MULTI
TV/DBS VIDEO
VCR1 VCR2
SURROUND DSP
ANALOG BASS
DIRECT BOOST
SOUND TEST
DIMMER
7/P
∗
MUTING DIGITAL EQ
10
RETURN
CATV/DBS
CONTROL
∗
CH/
TV/VIDEO
TEXT
DISPLAY MENU
REC
PAUSE
DOWN – TUNING – UP
SLEEP
RM-SRX8020J
Note:
When you press one of the source selecting buttons, the
operation mode appears on the display window. For example,
the above illustration shows the remote control now works for
VCR 1 operation.
Buttons
VCR1
DVD or DVD MULTI
TV/DBS
CONTROL (repeatedly)*
* By pressing CONTROL repeatedly, you can select "VCR1,"
"TAPE," "CDR" or "CDDSC" as the source.
53
TV AUDIO
CD FM/AM
CDR PHONO
TAPE/MD USB
SURR/DSP ANALOG/DIGITAL
OFF INPUT
∗ ∗
FRONT•L FRONT•R
1 2 3
MENU
∗ ∗
CENTER SUBWFR
4 5 6
ENTER
∗ ∗
SURR•L SURR•R
8 9
∗ ∗
SBACK•L SBACK•R
0
+10
100 +
FM MODE
+ + +
LEVEL TV VOL VOLUME
− − −
PLAY
EXIT
/REW FF/
PAUSE
SET
STOP CONTROL
REMOTE CONTROL
Indications
VCR1
DVD
TV
VCR1 TAPE
CDR
CDDSC
VCR 1 (VCR connected to the VCR 1 jacks)
You can always perform the following operations:
VCR1 :Turn on or off the VCR 1 (VCR connected to
the VCR 1 jacks).
After pressing VCR1 (or selecting "VCR1" by pressing CONTROL
repeatedly), you can perform the following operations on the VCR 1
(VCR connected to the VCR 1 jacks):
1 – 9, 0 :Select the TV channels on a VCR.
3 PLAY
:Start playing.
REW
:Rewind a tape.
FF :Fast wind a tape.
7 STOP
:Stop playing or recording.
8 PAUSE :Pause playing. To resume press 3 PLAY.
REC PAUSE :Enter recording pause by pressing this button.
To start recording again, press this button then
3 PLAY.
CH +/–
:Change the TV channels on the VCR.
Note:
You can use either VCR1 or CONTROL to activate the buttons listed
above. If you press VCR1, the playing source also changes. On the
other hand, if you press CONTROL repeatedly to select "VCR1," the
playing source does not change.
DVD player
After pressing DVD or DVD MULTI, you can perform the
following operations on a DVD player:
3 PLAY
:Start playing.
4
:Return to the beginning of the current (or
previous) chapter.
¢
:Skip to the beginning of the next chapter.
7 STOP
:Stop playing.
8 PAUSE :Pause playing. To resume press 3 PLAY.
After pressing DVD or DVD
MULTI, these buttons can be used
for the DVD menu operations.
Note:
For detailed menu operations, refer
to the instructions supplied with the
discs or the DVD player.
TV
You can always perform the following operations:
TV :Turn on or off the TV.
TV VOL +/– :Adjust the volume.
TV/VIDEO
:Set the input mode (either TV or VIDEO).
After pressing TV/DBS, you can perform the following operations
on a TV:
CH +/– :Change the channels.
1 – 9, 0, 100+ :Select the channels.
RETURN :Alternate between the previously selected
channel and the current channel.
∗FRONT•L ∗FRONT•R
2 3
MENU MENU
∗CENTER
∗SUBWFR
TEST
4 5 6
ENTER ENTER
∗SURR•L
8