Table of Contents
Advertisement
e. Maintain power tools. Check for misalignment or
binding of moving parts, breakage of parts and any
other condition that may affect the power tools
operation. If damaged, have the power tool repaired
before use. Many accidents are caused by poorly
maintained power tools.
f. Keep cutting tools sharp and clean. Properly
maintained cutting tools with sharp cutting edges are less
likely to bind and are easier to control.
g. Use the power tool, accessories and tool bits etc.,
in accordance with these instructions, taking into
account the working conditions and the work to be
performed. Use of the power tool for operations different
from those intended could result in a hazardous situation.
5. Battery tool use and care
a. Recharge only with the charger specified by the
manufacturer. A charger that is suitable for one type of
battery pack may create a risk of fire when used with
another battery pack.
b. Use power tools only with specifically designated
battery packs. Use of any other battery packs may create
a risk of injury and fire.
c. When battery pack is not in use, keep it away from
other metal objects, like paper clips, coins, keys, nails,
screws, or other small metal objects, that can make a
connection from one terminal to another. Shorting the
battery terminals together may cause burns or a fire.
d. Under abusive conditions, liquid may be ejected from
the battery; avoid contact. If contact accidentally
occurs, flush with water. If liquid contacts eyes,
additionally seek medical help. Liquid ejected from the
battery may cause irritation or burns.
6. Service
a. Have your power tool serviced by a qualified repair
person using only identical replacement parts. This will
ensure that the safety of the power tool is maintained.
b. The tool always is supplied via residual current device with
a rated residual current of 30 mA or less.
SPECIFIC SAFETY RULES
Hold tool by insulated gripping surfaces when
◆
performing an operation where the cutting tool may
contact hidden wiring or its own cord. Contact with a
"live" wire will make exposed metal parts of the tool "live"
and shock the operator.
Avoid body contact with grounded surfaces such as
◆
pipes, radiators, ranges and refrigerators. There is an
increased risk of electric shock if your body is grounded.
4
The label on your tool may include the following symbols.
V....................volts
A....................Amperes
Hz..................Hertz
W...................Watts
min.................Minutes
.................Alternating Current
.................Direct Current
n0...................No Load Speed
..................Class II Construction
..................Earthing Terminal
..................Safety alert symbol
.../min ............revolutions or reciprocations per minute
WARNING!Some dust created by power sanding, sawing,
grinding, drilling, and other construction activities contains
chemicals known to cause cancer, birth defects or other
reproductive harm. Some examples of these chemicals are:
Lead from lead-based paints,
◆
crystalline silica from bricks and cement and other
◆
masonry products, and arsenic and chromium from
chemically-treated lumber. (CCA)
Your risk from these exposures varies, depending on how
often you do this type of work. To reduce your exposure to
these chemicals: work in a well ventilated area, and work with
approved safety equipment, such as those dust masks that
are specially designed to filter out microscopic particles.
Avoid prolonged contact with dust from power
◆
sanding, sawing, grinding, drilling, and other
construction activities. Wear protective clothing and
wash exposed areas with soap and water. Allowing dust
to get into your mouth, eyes, or lay on the skin may
promote absorption of harmful chemicals.
FEATURES (FIGURE A)
1. On / Off Switch (forward direction)
2. On / Off Switch (reverse direction)
3. Spindle lock collar
4. Bit holder sleeve
5. Battery holder
BATTERY INSTALLATION
The AD600 drill/driver uses four size AA alkaline batteries only.
To install batteries in your tool, remove the battery holder end
cap (5) by depressing the two tabs (7), as shown in Figure B.
Pull the battery holder out of the tool, as shown in Figure C
and observe the battery position instructions printed on the
battery holder. (The plus and minus ends of the batteries are
marked with + and - signs.)
Advertisement
Table of Contents
