Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Subscribe to Our Youtube Channel
Related Manuals for 909 909C12V
Summary of Contents for 909 909C12V
- Page 1 INSTRUCTION MANUAL 909C12V VA RI A BL E SPEED OSCIL L AT ING MULT I TOOL...
-
Page 2: Table Of Contents
CONTENTS Warranty Power Tools Warranty Introduction For full details please visit us at www.909.com Environmental protection Description of symbols Specifications General safety rules Additional safety instructions for the charger Additional safety instructions related to the battery pack and battery safety... -
Page 3: Environmental Protection
Manual before using your new 909 Power Tool. Take special care to heed the Cautions and Warnings. Conforms to relevant standards Your 909 power tool has many features that will make for electromagnetic compatibility. your job faster and easier. Safety, performance, and... -
Page 4: General Safety Rules
General safety rules f) To reduce the risk of electric shock, the manufacturer recommends the use of a residual current device WARNING. Read all safety warnings and all instructions. with a rated residual current of 30mA or less at Failure to follow the warnings and instructions may result in all times. -
Page 5: Additional Safety Instructions For The Charger
4) Power tool use and care i) Children should be supervised to ensure that they do not play with the appliance. a) Do not force the power tool. Use the correct power tool for your application. The correct power tool will 5) Service do the job better and safer at the rate for which it was a) Have your power tool serviced by a qualified repair... - Page 6 WARNING. We recommend the use of a residual current • Do not plug anything other than your 909 tool into the device with a residual current rating of 30mA or less. charger, as other objects may touch dangerous voltage Wear goggles...
-
Page 7: Additional Safety Instructions Related To The Battery Pack And Battery Safety
• To reduce the risk of an electric shock, unplug the charger • Use only the 909 batteries supplied with the 909 Tool or from the power supply before attempting to 909-approved replacements. clean it. To clean tool or charger, wipe with a damp cloth. -
Page 8: When To Charge The Battery
• Take care where the tool is stored. Do not store in areas Important information – Product care of corrosive fumes, or salt air or similar conditions. Try This oscillating tool uses lithium ion battery cells. Care and store the tool in the packaging supplied with the tool. MUST be taken to ensure both the safety and life of the •... -
Page 9: Accessories
Due to modern mass production techniques, it is unlikely suggested to stop using the tool and recharge the battery. that your 909 Power Tool is faulty or that a part is missing. For storage, it is suggested to recharge the battery between If you find anything wrong, do not operate the tool until the 50% and 75% charge. -
Page 10: Know Your Product
Know your product 1. On/Off switch 2. Variable speed control wheel 3. Battery Indicator light 4. Battery 5. Battery release tabs (on both sides) 6. Battery charger base 7. Battery charger adaptor 8. LED work light (not shown) 9. Accessory Adaptor 10. -
Page 11: Installing Accessories
1. The accessory adaptor (9) is used for accessories that 5mm hex key if the screw is too tight to be removed by are not 909 branded. This includes Bosch, Dremel and hand. WorX accessories with an inner circular bore of 10mm diameter. -
Page 12: Installing Sandpaper
4. Place the non 909 brand Notes: accessory over the accessory a) Place the sandpaper so the holes in the sandpaper adaptor (9) and place in line up with the matching holes in the hook & loop pad. position as required. The b) Press the sandpaper firmly onto the hook &... -
Page 13: To Obtain The Best Life For The Battery
If the green light does not come on and the red light is To obtain the best life for the battery illuminated on the adaptor, the cells are not charging and Never allow the oscillating tool to come to a complete stand the cells require some time to cool. -
Page 14: Speed Control Wheel
and red. When the green light goes out leaving the yellow Flush cutting a door jamb and casing for and red, the battery level is approx 1/2 to 3/4 charge. When installing flooring the yellow light goes out, leaving just the red, the charge The oscillating level is approx 1/4 charged, and is recommended to stop tool can be used... -
Page 15: Cutting A Hole In Wood Flooring To Install A Heating Vent
Follow the same basic procedure for installing carpet, using 7. Repeat steps #4, #5 & #6 to cut the remaining three a thicker spacer that is the same thickness of the carpet sides of the rectangle. being installed. 8. When all cuts are complete, use a flat blade screw driver to carefully pry the cut-out from the floor. -
Page 16: Using The Detail Sander Attachment
of gouging the workpiece. Note: Hold the tool tightly and do not put too much pressure on the saw blade when cutting. When using the scraper blade to cut carpet, place a scrap workpiece under the carpet where the cut is being made. 6.
Need help?
Do you have a question about the 909C12V and is the answer not in the manual?
Questions and answers