Keypad Programming - DSC PTK5507 Installation Instructions Manual

Dark Text Enable/Disable
1. Press Options, Installer Menu [Installer Code], Keypad Programming, then Options.
2. Select the desired text color by enabling or disabling Dark Text. (Disabling makes the text
white.)
NOTE: This feature affects only the text on the Classic (Square) Button Home Page.
Changing Home Page Look:
1. Press Options, Keypad Config, Home Page.
2. Select the desired view from either classic look (square) or contemporary (rondel).
3. To exit, press the Back or Home button.
Performing a Firmware Upgrade:
1. Insert an SD card in the PTK5507 with the new firmware.
2. Press Options, Installer Menu [Installer Code], Keypad Programming, then Firmware
Upgrade.
3. Select OK to perform a firmware update (if a new firmware version is available).
Enabling/Disabling Fire, Auxiliary and Panic Buttons
alarm shop
1. Press Options, Installer Menu [Installer Code], Keypad Programming, then Options.
2. Enable/disable the desired Fire, Auxiliary and Panic buttons.
NOTE: The Fire, Auxiliary and Panic buttons are enabled by default on the PTK5507.
Extra Power Option
The Extra Power option will increase the brightness of the display. To enable the option:
1. Press Options, Installer Menu [Installer Code], Keypad Programming, then Options.
2. Enable or disable the extra power option.
NOTE: Enabling the Extra Power option will put the keypad in a higher current mode and the key-
pad will draw 400 mA.
Changing Function Keys on the Home Page:
1. Press Options, Installer Menu [Installer Code], Keypad Programming, then Home Functions.
2. Assign the desired function to the corresponding key.
3. To exit press the Back or Home button.
Adjusting Screen Time out
1. Press Options, Keypad Config, then Backlight.
2. Select appropriate time for screen time out by using the slide bar.
3. To exit, press Back or Home button.
Accessing Clean Mode
Press Options, Keypad Config, Clean Mode.
NOTE: Clean mode will time out in 30 seconds.
Keypad Enrollment
Enter keypad programming by pressing Options, Installer Menu [Installer's Code], Keypad
Mode Prog, then [000].
[0] Partition / Slot Assignment
Digit Option
1st Partition Assignment (0=Global Keypad)
2nd Slot Assignment
[1]-[5] Function Key Assignment
Do not attempt to change the function key programming or the home page buttons may not
function as desired.

Keypad Programming

Enter keypad programming by pressing Options, Installer Menu [Installer's Code], Keypad
Mode Prog, then [000].
[001]-[064] Zone Label 1 to 64
ex. For Zone 1 enter section [001], for Zone 2 enter section [002] etc. Default: "Zone 1"-"Zone 64"
Section Zone
[001]
I _ _ _ _ _ I _ _ _ _ _ I _ _ _ _ _ I _ _ _ _ _ I _ _ _ _ _ I _ _ _ _ _ I _ _ _ _ _ I _ _ _ _ _ I _ _ _ _ _ I _ _ _ _ _ I _ _ _ _ _ I _ _ _ _ _ I _ _ _ _ _ I _ _ _ _ I
1 to
to
64 I _ _ _ _ _ I _ _ _ _ _ I _ _ _ _ _ I _ _ _ _ _ I _ _ _ _ _ I _ _ _ _ _ I _ _ _ _ _ I _ _ _ _ _ I _ _ _ _ _ I _ _ _ _ _ I _ _ _ _ _ I _ _ _ _ _ I _ _ _ _ _ I _ _ _ _ I
[064]
[077] Second Keypad Options
Default Option
Chime Enabled for Zone
I____I 1
ON
Openings
Chime Enabled for Zone
I____I 2
ON
Closings
I____I 3
OFF For Future Use
I____I 4
ON For Future Use
I____I 5
OFF For Future Use
I____I 6
ON For Future Use
I____I 7
ON For Future Use
I____I 8
OFF For Future Use
NOTE: Do not attempt to change options 3-8 in Section 077 or the keypad may not function as
desired.
Valid Range Default
0 to 8 1
1 to 8 8
Label
ON OFF
Chime Disabled for Zone
Openings
Chime Disabled for Zone
Closings
I_____I
I_____I