Sony DCR-TRV240 Service Manual page 30

DCR-TRV240/TRV340
Dubbing only desired scenes – Digital program editing (on tapes)
3
VIDEO EDIT 0:08:55:06
EDIT SET
CONTROL
ADJ TEST RETURN
"CUT–IN" EXECUTE
"CUT–OUT"
IR SETUP ENGAGE
PAUSEMODE REC PAUSE
IR TEST
RETURN
[MENU] : END
7
VIDEO EDIT 0:08:55:06
EDIT SET
CONTROL
ADJ TEST
"CUT–IN" 0
"CUT–OUT"
IR SETUP
PAUSEMODE
IR TEST
RETURN
[MENU] : END
Notes
• When you complete step 3, the image used to adjust synchronization is recorded for
about 50 seconds.
• If you start recording from the very beginning of the tape, the first few seconds of the
tape may not record properly. Be sure to allow about 10 seconds' lead before starting
recording.
• When you connect with an i.LINK cable (DV connecting cable) you may not be able to
operate the dubbing function correctly, depending on the VCR.
Keep the i.LINK connection, and set CONTROL to IR in the menu settings.
Video and audio signals are transmitted in digital format.
82
Dubbing only desired scenes – Digital program editing (on tapes)
MENU
4
For DCR-TRV240:
OTHERS
DATA CODE
BEEP
COMMANDER
DISPLAY
VIDEO EDIT READY
INDICATOR
RETURN
[MENU] : END
For DCR-TRV340:
OTHERS
DATA CODE
BEEP
COMMANDER
DISPLAY
VIDEO EDIT RETURN
INDICATOR TAPE
RETURN MEMORY
[MENU] : END
8
VIDEO EDIT 0:09:07:06
MARK 2 IN
UNDO
ERASE ALL
START
EDIT SET
TOTAL 0:00:12:00
SCENE 1
[MENU] : END
84
4
VIDEO EDIT 0:08:55:06 VIDEO EDIT 0:08:55:06
EDIT SET EDIT SET
CONTROL CONTROL
ADJ TEST EXECUTING ADJ TEST COMPLETE
"CUT–IN" "CUT–IN"
"CUT–OUT" No. 5 "CUT–OUT"
IR SETUP IN IR SETUP
PAUSEMODE –60 PAUSEMODE
IR TEST IR TEST
RETURN RETURN
[MENU] : END [MENU] : END
9
VIDEO EDIT 0:08:55:06
EDIT SET
CONTROL
ADJ TEST
"CUT–IN"
"CUT–OUT" 0
IR SETUP
PAUSEMODE
IR TEST
RETURN
[MENU] : END
5
VIDEO EDIT 0:08:55:06 VIDEO EDIT 0:08:55:06
MARK 1 IN MARK 1 IN
UNDO UNDO
ERASE ALL ERASE ALL
START START
EDIT SET EDIT SET
TOTAL 0:00:00:00 TOTAL 0:00:00:00
SCENE 0 SCENE 0
[MENU] : END
[MENU] : END
6
VIDEO EDIT 0:08:55:06
VIDEO EDIT 0:08:55:06
MARK 1 IN
MARK 1 OUT
UNDO
UNDO
ERASE ALL
ERASE ALL
START
START
EDIT SET
EDIT SET
TOTAL 0:00:00:00
TOTAL 0:00:00:00
SCENE 0
SCENE 0
[MENU] : END
[MENU] : END
9
VIDEO EDIT 0:10:01:23
MARK 4 IN
UNDO
ERASE ALL
START
EDIT SET
TOTAL 0:00:47:12
SCENE 3
[MENU] : END
Dubbing only desired scenes – Digital program editing (on tapes)
Operation 1: Making a program
(1) Insert the tape for playback into your camcorder, and insert a tape for
recording into the VCR.
(2) Press MENU to display the menu settings.
(3) Turn the SEL/PUSH EXEC dial to select
(4) For DCR-TRV240:
Turn the SEL/PUSH EXEC dial to select VIDEO EDIT, then press the dial.
For DCR-TRV340:
Turn the SEL/PUSH EXEC dial to select TAPE in VIDEO EDIT, then press the
dial.
(5) Search for the beginning of the first scene you want to insert using the video
operation buttons, then pause playback.
You can fine-adjust one frame at a time with EDITSEARCH.
(6) Press the SEL/PUSH EXEC dial.
The IN point of the first program is set, and the top part of the program mark
changes to light blue.
(7) Search for the end of the first scene you want to insert using the video
operation buttons, then pause playback.
(8) Press the SEL/PUSH EXEC dial.
The OUT point of the first program is set, then the bottom part of the program
mark changes to light blue.
(9) Repeat steps 5 to 8, then set the program.
When the program is set, the program mark changes to light blue.
You can set up to 20 programs.
Dubbing only desired scenes – Digital program editing (on tapes)
Erasing the program you have set
Erase OUT first and then IN from of the last program.
(1) Turn the SEL/PUSH EXEC dial to select UNDO, then press the dial.
(2) Turn the SEL/PUSH EXEC dial to select EXECUTE, then press the dial.
The last set program mark flashes, then the setting is canceled.
To cancel erasing
Select RETURN in step 2.
Erasing all programs
(1) For DCR-TRV240:
Turn the SEL/PUSH EXEC dial to select VIDEO EDIT, then press the dial.
For DCR-TRV340:
Select VIDEO EDIT in the menu settings. Turn the SEL/PUSH EXEC dial to
select TAPE, then press the dial.
(2) Select ERASE ALL in the menu settings. Turn the SEL/PUSH EXEC dial to
select EXECUTE, then press the dial.
All the program marks flash, then the settings are canceled.
To cancel erasing all programs
Select RETURN in step 2.
To cancel a program you have set
Press MENU.
The program is stored in memory until the tape is ejected.
Notes
•Digital program editing does not work when PB MODE is set to
settings.
•You cannot operate recording during Digital program editing.
You cannot set IN or OUT to the following portions of the tape:
– A blank portion of the tape
– A portion recorded in a system other than Digital8
The total time code may not be displayed correctly in the following cases:
– The tape is not recorded in the Digital8
– There is a blank portion between IN and OUT on the tape.
1-20
, then press the dial.
83
/ in the menu
system.
85