Sony DCR-TRV240 Service Manual page 28

DCR-TRV240/TRV340
Dubbing only desired scenes – Digital program editing (on tapes)
Step 1: Connecting the VCR
You can connect both an A/V connecting cable and an i.LINK cable (DV connecting
cable).
When you use the A/V connecting cable, connect the devices as illustrated in page 70.
When you use an i.LINK cable (DV connecting cable), connect the devices as illustrated
on page 71.
If you connect using an i.LINK cable (DV connecting cable)
With a digital-to-digital connection, video and audio signals are transmitted in digital
format for high-quality editing.
Step 2: Setting the VCR to operate with the A/V connecting cable
To edit using the VCR, send the control signal by infrared rays to the remote sensor on
the VCR.
When you connect using an A/V connecting cable, follow the procedure below, steps
(1) to (4), to send the control signal correctly.
(1) Set the IR SETUP code
1 Set the POWER switch to VCR on your camcorder.
2 Turn the power of the connected VCR on, then set the input selector to LINE.
When you connect a video camera recorder, set its power switch to VCR/VTR.
3 Press MENU to display the menu settings.
4 Turn the SEL/PUSH EXEC dial to select
5 For DCR-TRV240:
Turn the SEL/PUSH EXEC dial to select VIDEO EDIT, then press the dial.
For DCR-TRV340:
Turn the SEL/PUSH EXEC dial to select TAPE in VIDEO EDIT, then press the
dial.
6 Turn the SEL/PUSH EXEC dial to select EDIT SET, then press the dial.
7 Turn the SEL/PUSH EXEC dial to select CONTROL, then press the dial.
8 Turn the SEL/PUSH EXEC dial to select IR, then press the dial.
9 Turn the SEL/PUSH EXEC dial to select IR SETUP.
0 Turn the SEL/PUSH EXEC dial to select IR SETUP code number of your VCR,
then press the dial.
Check the code in "About IR SETUP codes." (p. 76)
74
Dubbing only desired scenes – Digital program editing (on tapes)
About IR SETUP codes
The IR SETUP code is stored in the memory of your camcorder. Be sure to set the
correct code to match your VCR. The default setting is code number 3.
Brand IR SETUP code
Sony 1, 2, 3, 4, 5, 6
Admiral (M. Wards) 89
Aiwa 47, 54, 80
Akai 49, 51
Audio Dynamic 21, 35
Bell&Howell 36
(M. Wards)
Broksonic 21, 70, 82
Canon 77, 78
Citizen 47
Craig 47, 73
Curtis Mathis 8, 77, 80
Daewoo 26, 40, 77
DBX 21, 33, 35
Dimensia 8
Emerson 26, 48, 59, 70, 80, 81, 82
Fisher 36, 37, 44, 45
Funai 80
General Electric 8, 32*, 77, 94*, 101
Goldstar/LG 47
GO VIDEO 71
Hitachi 8, 42, 78
HQ 40
Instant Replay 77, 78
JC Penny 8, 21, 33, 35, 36, 42, 77
JVC 12, 13, 14, 21, 33, 35
Kenwood 21, 33, 35, 47
LXI (Sears) 36, 37, 42, 44, 45, 47, 49, 80
Magnavox 17, 77, 78, 83
Marantz 21, 33, 35
Marta 47
Memorex 37, 77
Minolta 8, 42
* TV/VCR component
Note on IR SETUP codes
Digital program editing is not possible if the VCR does not support IR SETUP codes.
76
, then press the dial.
Brand IR SETUP code
Mitsubishi/MGA 22, 23, 24, 28, 29
Multitech 23, 32, 80
NEC 21, 33, 35
Olympic 77, 78
Optimus 22
Orion 60
Panasonic 16, 17, 77, 78
Pentax 8, 42
Philco 26, 70, 77, 78
Philips 47, 77, 78, 83
Pioneer 78
Quasar 6, 16, 17, 77, 78
RCA/PROSCAN 7, 8, 16, 40, 41, 42, 77, 78, 78*, 83,
101
Realistic 22, 36, 37, 77, 80, 88
Sansui 21
Singer 73
Samsung 24, 24*, 32, 32*, 41, 94, 94*
Sanyo 26, 36, 37, 47
Scott 22, 23, 24, 28, 32, 37, 40, 41
Sharp 88, 89
Shintom 73
Signature 2000 80, 89
Sylvania 77, 78, 80, 83
Symphonic 80
Tashiro 47
Tatung 21, 33, 35
Teac 21, 33, 35, 80
Technics 77, 78
Toshiba 7, 40, 49
Wards 37, 47, 88, 89, 95
Yamaha 21, 33, 35, 36
Zenith 95
1-18
Dubbing only desired scenes – Digital program editing (on tapes)
MENU
5
For DCR-TRV240:
OTHERS VIDEO EDIT
DATA CODE MARK
BEEP UNDO
COMMANDER ERASE ALL
DISPLAY START
VIDEO EDIT READY EDIT SET
INDICATOR
RETURN TOTAL 0:00:00:00
SCENE 0
[MENU] : END
[MENU] : END
For DCR-TRV340:
OTHERS VIDEO EDIT
DATA CODE MARK
BEEP UNDO
COMMANDER ERASE ALL
DISPLAY START
VIDEO EDIT RETURN EDIT SET
INDICATOR TAPE
RETURN MEMORY TOTAL 0:00:00:00
SCENE 0
[MENU] : END
[MENU] : END
10
VIDEO EDIT 0:08:55:06
EDIT SET
CONTROL
ADJ TEST
"CUT–IN"
"CUT–OUT"
IR SETUP 3
PAUSEMODE
IR TEST
RETURN
[MENU] : END
Dubbing only desired scenes – Digital program editing (on tapes)
(2) Setting the modes to cancel the recording pause on the VCR
1 Turn the SEL/PUSH EXEC dial to select PAUSEMODE, then press the dial.
2 Turn the SEL/PUSH EXEC dial to select the mode to cancel recording pause
on the VCR, then press the dial.
Refer to the operating instructions of your VCR.
VIDEO EDIT
EDIT SET
CONTROL
ADJ TEST
"CUT–IN"
"CUT–OUT"
IR SETUP
PAUSEMODE PAUSE
IR TEST REC
RETURN PB
[MENU] : END
Buttons to cancel recording pause on the VCR
The buttons vary depending on your VCR. To cancel recording pause:
– Select PAUSE if the button to cancel recording pause is X.
– Select REC if the button to cancel recording pause is z.
– Select PB if the button to cancel recording pause is N.
(3) Setting your camcorder and the VCR to face each other
Locate the infrared rays emitter of your camcorder and face it towards the remote
sensor of the VCR.
Set the devices about 30 cm (12 in.) apart, and remove any obstacles between the
devices.
VCR
Remote sensor
A/V connecting cable (supplied)
6
0:08:55:06
VIDEO EDIT 0:08:55:06
1 IN
MARK
UNDO
ERASE ALL
START
EDIT SET IR
TOTAL 0:00:00:00
SCENE 0
[MENU] : END
7
0:08:55:06 VIDEO EDIT 0:08:55:06
1 IN EDIT SET
CONTROL IR
ADJ TEST i. LINK
"CUT–IN"
"CUT–OUT"
IR SETUP
PAUSEMODE
IR TEST
RETURN
[MENU] : END
75
0:08:55:06 VIDEO EDIT 0:08:55:06
EDIT SET
CONTROL
ADJ TEST
"CUT–IN"
"CUT–OUT"
IR SETUP
PAUSEMODE PAUSE
IR TEST
RETURN
[MENU] : END
Infrared rays emitter
77