Mode-Am Group; Mode-Cw Group; Am Lcut Freq; Cw Lcut Freq - Yaesu FT dx 1200 Operating Manual

m m
enu oDe
Mode-AM g

050 AM LCUT FREQ

Function: Selects the cutoff frequency of the lower side
of the RX audio filter in the AM mode.
Available Values: OFF/100 ~ 1000 Hz (50 Hz/step)
Default Setting: OFF

051 AM LCUT SLOPE

Function: Selects the filter slope of the lower side of the
RX audio filter in the AM mode.
Available Values: 6dB/oct / 18dB/oct
Default Setting: 6dB/oct

052 AM HCUT FREQ

Function: Selects the cutoff frequency of the upper side
of the RX audio filter in the AM mode.
Available Values: OFF/700 ~ 4000 Hz (50 Hz/step)
Default Setting: OFF

053 AM HCUT SLOPE

Function: Selects the filter slope of the upper side of the
RX audio filter in the AM mode.
Available Values: 6dB/oct / 18dB/oct
Default Setting: 6dB/oct
054 AM MIC GAIN
Function: Sets the microphone gain for the AM mode.
Available Values: MVCR/0 ~ 100
Default Setting: 30
When this menu is set to "MCVR", you may adjust the
microphone gain using the front panel [MIC/SPEED]
knob.
055 AM MIC SEL
Function: Selects the microphone to be used in the AM
mode.
Available Values: FRONT / DATA
Default Setting: FRONT
FRONT: Selects the microphone connected to the
front panel MIC jack while using the AM
mode.
DATA: Selects the microphone connected to pin 1 of
the PACKET Jack while using the AM mode.
Page 116
roup
056 CW PITCH
Function: Adjusts your preferred CW tone pitch.
Available Values: 300 ~ 1050 Hz (50 Hz/step)
Default Setting: 700 Hz

057 CW LCUT FREQ

Function: Selects the cutoff frequency of the lower side
of the RX audio filter in the CW mode.
Available Values: OFF/100 ~ 1000 Hz (50 Hz/step)
Default Setting: 250

058 CW LCUT SLOPE

Function: Selects the filter slope of the lower side of the
RX audio filter in the CW mode.
Available Values: 6dB/oct / 18dB/oct
Default Setting: 18dB/oct

059 CW HCUT FREQ

Function: Selects the cutoff frequency of the upper side
of the RX audio filter in the CW mode.
Available Values: OFF/700 ~ 4000 Hz (50 Hz/step)
Default Setting: 1200

060 CW HCUT SLOPE

Function: Selects the filter slope of the upper side of the
RX audio filter in the CW mode.
Available Values: 6dB/oct / 18dB/oct
Default Setting: 18dB/oct
061 CW AUTO MODE
Function: Enables/disables CW keying while operating
on SSB.
Available Values: OFF/50M/ON
Default Setting: OFF
OFF: Disables CW keying while operating on SSB.
50:
On: Enables CW keying while operating on SSB (all
062 CW BFO
Function: Sets the CW carrier oscillator injection side
for the CW mode.
Available Values: USB/LSB/AUTO
Default Setting: USB
USB:
LSB:
AUTO: Injects the CW carrier oscillator on the LSB
Mode-cw g
Enables CW keying only while operating SSB on
50 MHz (but not HF).
TX bands).
Injects the CW carrier oscillator on the USB
side.
Injects the CW carrier oscillator on the LSB
side.
side while operating on the 7 MHz band and
below, and the USB side while operating on the
10 MHz band and up.
FT 1200 O
DX peraTing
roup
M
anual