Using Timer - JVC DR-MV5S Instructions Manual

®
VCR Plus+ Timer Programing
You can program each deck to timer-record as many as
8 programs up to 30 days ahead.
With the VCR Plus+ system, timer programing is greatly simplified
because each TV program has a corresponding code number
which your unit is able to recognize.
You can use the remote control to enter the PlusCode number.
Make sure that the unit's built-in clock is set properly.
Turn on the unit.
Turn on the TV and select the AV mode.
Slide the TV/DVD switch to DVD.
VHS
0 – 9
CANCEL
VCR Plus+
ENTER
IMPORTANT:
If you have moved to a different area or if a broadcasting station's
channel number has been changed, the wrong channel number will
be displayed on the VCR Plus+ program screen in step 5. When this
happens, set the correct Guide Channel number for that station.
( pg. 77, "Changing VCR Plus+
Cable Box and DBS Receiver Users (DVD Deck Only)
To timer-record a satellite broadcast using the VCR Plus+
system:
®
A Perform "VCR Plus+
Timer Programing".
B Set the cable box or DBS receiver to the appropriate channel
before the selected program begins.
C Leave the cable box or DBS receiver's power on.
NOTES:
There may be cases that the VCR Plus+ Timer Programing function
prolongs the stop time of the programing.
When two successive programs are recorded on a DVD-RW disc with
the VCR Plus+ Timer Programing function, the beginning of the
second one may be left off the recording.
VCR Plus+ Timer Programing is not possible on the discs used
exclusively for On-Disc Timer Programing.
If the copy limited program is received during timer-recording, the unit
enters Record Pause mode. Recording starts again if it is switched to
a recordable broadcast during the time you programed.
To record the programs received by cable box or DBS receiver,
record on the DVD discs. For details, refer to "Cable Box and DBS
Receiver Users (DVD Deck Only)" above.
DVD
TIMER
rtwe
RETURN
CLEAR (8)
®
Setting")
1
Press DVD or VHS to select the deck on which you want to
perform timer programing.
2
For DVD deck
Load a recordable disc.
For VHS deck
Load a cassette with safety tab intact.
3
Press VCR Plus+ to access the VCR Plus+ screen.
4
Press the number buttons to
enter the PlusCode number of a
program you wish to record, then
press ENTER.
If you have made a mistake, press
CANCEL and input the correct
number before you press ENTER.
To clear all entered numbers at a
time, press CLEAR (8).
If the number you entered is
invalid, "PLUSCODE NO. ERROR CONFIRM PLUSCODE NO.
THEN RETRY" appears on the TV screen. Input a valid PlusCode
number.
If "GUIDE PROGRAM IS NOT SET" appears on the TV screen, set
Guide Channel numbers manually. (
When "PROGRAM FULL DELETE UNWANTED TIMER PROGRAM"
appears on the TV screen, you need to cancel some of the reserved
programs. ( pg. 35)
5
The PlusCode number you entered and the matching timer-
recording information are displayed on the TV screen. Check the
program data.
To cancel this setting, press RETURN.
IMPORTANT:
Make sure the channel position number you wish to record is
displayed; if not, see "Changing VCR Plus+
set the Guide Program number correctly.
6
Press w e to select the desired recording option as required.
Press rt to select the desired setting, then press ENTER.
"STOP" (To advance/go back the stop time by 30 minutes, press and
hold rt).
"DAILY/WEEKLY" ( below "Weekly/Daily Recording")
"REC MODE" ( pg. 29, 30, "Recording Mode")
"NAME" ( pg. 64, "Modify Title Name") (DVD deck only)
7
Press ENTER to access the Program Confirmation screen.
8
Press ENTER to complete timer programing.
To program another timer, repeat steps 3 – 8.
If "PROGRAM OVERLAPPED" appears on the TV screen, see
page 35.
9
Press TIMER # to engage the unit's timer mode. The DVD timer
lamp lights up on the unit and the unit is automatically turned off.
To disengage the timer mode, press TIMER # again.
Weekly/Daily Recording
You can record programs with one of the following weekly/daily
timer settings.
WEEKLY
: Select to record a weekly program.
MON–FRI
: Select to record a daily program from Monday through
Friday.
MON–SAT
: Select to record a daily program from Monday through
Saturday.
SUN–SAT
: Select to record a daily program from Sunday through
Saturday.
TIMER RECORDING
31
EN
VCR Plus+ PRGM
PLUSCODE NO. 1 2 3 4
DATE START STOP CH
DAILY/WEEKLY REC MODE
NAME
SP
OK
1 2 3
ENTER VCR PLUS+ CODE WITH [0 - 9] KEYS
4 5 6
7 8 9 THEN PRESS [ENTER]
0
pg. 77)
®
Setting" ( pg. 77) and