Table of Contents
Advertisement
7
7
The front panel display switches over for no apparent
reason to various different displays.
This happens because the demo display is in operation. To turn
off the demo display, press any button to go back to the
original display, or set the FL Demo Mode to OFF (see
Demo Mode menu on page
31).
HDMI
No picture or sound.
If the problem still persists when connecting your HDMI
component directly to your monitor, please consult the
component or monitor manual or contact the manufacturer for
support.
No picture.
Video signals that are input from the analog video terminal will
not output from the HDMI terminal. Signals that are input from
the HDMI terminal will not output from the analog video
terminal. Be consistent with the type of cable between input
and output.
Depending in the output settings of the source component, it
may be outputting a video format that can't be displayed.
Change the output settings of the source, or connect using the
composite video jacks.
This receiver is HDCP-compatible. Check that the components
you are connecting are also HDCP-compatible. If they are not,
please connect them using the composite video jacks.
Depending on the connected source component, it's possible
that it will not work with this receiver (even if it is HDCP-
compatible). In this case, connect using the composite video
jacks between source and receiver.
If video images do not appear on your TV, try adjusting the
resolution, Deep Color or other setting for your component.
To output signals in Deep Color, use an HDMI cable (High
®
Speed HDMI
Cable) to connect this receiver to a component
or TV with the Deep Color feature.
The OSD screen (Home Menu, etc.) isn't displayed.
The OSD will not appear if you have connected using the HDMI
output to your TV. Use composite connections when setting up
the system.
No sound, or sound suddenly ceases.
Check that the HDMI setting is set to AMP
If the component is a DVI device, use a separate connection for
the audio.
HDMI format digital audio transmissions require a longer time
to be recognized. Due to this, interruption in the audio may
occur when switching between audio formats or beginning
playback.
Turning on/off the device connected to this unit's HDMI OUT
terminal during playback, or disconnecting/connecting the
The FL
HDMI cable during playback, may cause noise or interrupted
audio.
Important information regarding the HDMI
connection
There are cases where you may not be able to route HDMI
signals through this receiver (this depends on the HDMI
equipped component you are connecting-check with the
manufacturer for HDMI compatibility information).
If you aren't receiving HDMI signals properly through this
receiver (from your component), please try the following
configuration when connecting up.
Configuration
Connect your HDMI-equipped component directly to the
display using an HDMI cable. Then use the most convenient
connection (digital is recommended) for sending audio to the
receiver. See the operating instructions for more on audio
connections. Set the display volume to minimum when using
this configuration.
Note
•
Depending on the component, audio output may be limited
to the number of channels available from the connected
display unit (for example audio output is reduced to 2
channels for a monitor with stereo audio limitations).
•
If you want to switch the input source, you'll have to switch
functions on both the receiver and your display unit.
•
Since the sound is muted on the display when using the
HDMI connection, you must adjust the volume on the
display every time you switch input sources.
(page
26).
Resetting the main unit
Use this procedure to reset all the receiver's settings to the
factory default. Use the front panel controls to do this.
1
2
3
4
•
If the ARC function is ON, you may not be able to initialize
the unit. If this happens, turn OFF the ARC function or turn
OFF all the connected device before turning OFF
(STANDBY) the power for this unit, and initialize after the
HDMI indicator goes out.
Cleaning the unit
•
Use a polishing cloth or dry cloth to wipe off dust and dirt.
•
When the surface is dirty, wipe with a soft cloth dipped in
some neutral cleanser diluted five or six times with water,
and wrung out well, and then wipe again with a dry cloth.
Do not use furniture wax or cleansers.
•
Never use thinners, benzine, insecticide sprays or other
chemicals on or near this unit, since these will corrode the
surface.
34
Additional information
Switch the receiver into standby.
While holding down BAND, press and hold
STANDBY/ON
for about two seconds.
When you see RESET? appear in the display, press
AUTO SURROUND/STREAM
DIRECT.
'OK?' appears in the display.
Press
ALC/STANDARD SURR
to confirm.
'OK' appears in the display to indicate that the receiver
has been reset to the factory default settings.
Important
- Quick Links:
- Troubleshooting
- Specifications
Hide quick links:
Advertisement
Table of Contents
