General Information; Installation - Pentair Pool Products HIGH-RATE SAND FILTER SYSTEM Owner's Manual

GENERAL INFORMATION

• Clean a new pool as well as possible before filling
pool and operating filter. Excess dirt and large parti-
cles of foreign matter in the system can cause seri-
ous damage to the filter and pump.
NEVER test this filter with compressed air.
Do not operate filter at water temperatures
above 95°F (35°C).
NEVER operate this filter system at more than
50 pounds per square inch (50 PSI/345 kPa)
pressure!
Plug system into electrically isolated, Ground
Fault Circuit Interrupter protected circuit
ONLY!
• Clean a new pool as well as possible before filling
pool and operating filter. Excess dirt and large parti-
cles of foreign matter in the system can cause seri-
ous damage to the filter and pump.
• Keep pool water pH at recommended level (7.2 to
7.6) to avoid irritation to eyes and skin.
• The Hi-Rate Sand Filter System is designed for use
with above ground swimming pools only.
• Use only #20 Silica sand with a screen mesh of .45
to .55mm. Use of other sands will reduce filter
performance.
To reduce risk of electric shock, install
pump at least 10 feet from the inside wall of the pool.
Do not use an extension cord.

INSTALLATION

Trap to Pump Assembly:
Using four 5/16" cap screws, flat washers and lockwash-
ers, mount trap to pump body; be sure to install gasket
between trap and pump body. Tighten cap screws to 80
inch-lbs
(92 cm-kg) torque; do not overtighten.
Filter Mount Must:
• Provide weather and freezing protection.
• Provide space and lighting for easy access for routine
maintenance. (See Table I and Figure 1, Page 4, for
space requirements.)
• Be on a reasonably level surface and provide ade-
quate drainage.
• Be as close to pool as possible to reduce line loss
from pipe friction.
• Be solid – level– rigid – vibration free.
• Be installed so that trap suction inlet is below pool
water level at all times. This allows pump to prime.
• Have adequate ventilation to prevent motor
overheating.
Piping:
• Use teflon tape or Plasto-Joint Stik
nections of plastic pipe and fittings except unions.
DO NOT use pipe compounds on plastic pipe; it
will cause the pipe to crack. Do not use sealant or
tape on unions – assemble them dry and hand tight.
• Do not damage union sealing surfaces and "O" Rings.
• Support pipe independently to prevent strains on filter
and valve.
• Use 1-1/2 or 2" pipe to reduce pressure losses as
much as possible. If flex hose is used, use the type
with smooth internal walls.
• Fittings restrict flow; for best efficiency use fewest
possible fittings.
• Keep piping tight and free of leaks: pump suction line
leaks may cause trapped air in filter tank or loss of
prime at pump; pump discharge line leaks may show
up as dampness or jets of water.
• When unions are provided, use as follows for leak
free connections:
1. O-Ring and sealing surfaces must be clean.
2. Assemble hand tight only (no wrenches).
3. No pipe compound or teflon tape on unions.
Valves:
• For servicing filter system and for cleaning pump trap,
install ball or gate valves
A. Between pump trap and pool skimmer, and
B. Between selector valve and return pipe to pool.
• A check valve installed between filter and heater will
prevent hot water from backing up into filter and de-
forming internal components.
• Use care before assembly not to damage union seal-
ing surfaces or O Ring.
Wastewater:
• Be sure all provisions for waste water disposal meet
applicable local, state or national codes. 100 gallons
(379 liters) or more of pool water will be discharged
during filter backwashing. Do not discharge where
water will cause flooding or damage.
1
Lake Chemical Co., Chicago, IL
5
1
on all male con-