1. Manuals
  2. Brands
  3. Digital Equipment Manuals
  4. Printer Accessories
  5. DEClaser 3500
  6. Installation manual

Digital Equipment DEClaser 3500 Installation Manual

Printer external fax modem
Hide thumbs Also See for DEClaser 3500:
Table of Contents

Advertisement

Quick Links

Download this manual See also: User Manual
. . . . . . . . . . . . . . . . . . . . . . . .
DEClaser 3500 Printer
External Fax Modem

Installation Guide

Order Number: EK-D350P-EI.A01
Digital Equipment Corporation
Maynard, Massachusetts
190287-001 - 06/01/95 - - Saved by IDC - -
Rev # - File Name EXFX_US6.DOC

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the DEClaser 3500 and is the answer not in the manual?

Questions and answers

Related Manuals for Digital Equipment DEClaser 3500

Summary of Contents for Digital Equipment DEClaser 3500

  • Page 1: Installation Guide

    ......DEClaser 3500 Printer External Fax Modem Installation Guide Order Number: EK-D350P-EI.A01 Digital Equipment Corporation Maynard, Massachusetts 190287-001 - 06/01/95 - - Saved by IDC - - Rev # - File Name EXFX_US6.DOC...
  • Page 2 Possession, use, or copying of the software described in this publication is authorized only pursuant to a valid written license from Digital or an authorized sublicensor. © Digital Equipment Corporation 1994. All Rights Reserved.
  • Page 3 ......Approval Information for Australia Failure to set the modem, and any communications software used with the modem, to the values contained in the following table, will result in the modem being operated in a non- compliant manner.
  • Page 4 BABT Approval Information The Digital Equipment Corporation DEClaserFAX is made in England and is approved by BABT for connection to telecommunications systems specified in the instructions for use and subject to the conditions set out in them.
  • Page 5 ......For statutory purposes, apparatus connected to the PSTN through a Relevant Branch System (RBS) is treated as if connected directly to the PSTN.
  • Page 6 ......Connection to the telephone system: If the telephone line does not have a wall socket compatible with a type 431A plug, arrange for the installation of an appropriate socket and/or extension as follows: •...

  • Page 7: Safety Statement

    ......Safety Statement Before proceeding with the installation, you should read the following statement and the national appendix containing statutory information for the country in which you will be using the DEClaserFAX.

  • Page 8: Electrostatic Discharge

    ......Electrostatic Discharge A discharge of static electricity from a finger or other conductor may damage circuit boards or other static-sensitive devices. This type of damage may reduce the life expectancy of the device.
  • Page 9 ......INTRODUCTION The DEClaserFAX is an external modem for the DEClaser 3500 printer. The DEClaserFAX can send and receive Group III and PostScript faxes.

  • Page 10: Installation

    ......INSTALLATION STEP 1 TURN THE PRINTER OFF (O) AND UNPLUG THE POWER CORD. STEP 2 DISCONNECT ALL CABLES FROM THE PRINTER. 190287-001 - 06/01/95 - - Saved by IDC - - Rev # 2 - File Name EXFX_US6.DOC...
  • Page 11 ......Turn the printer off and unplug the AC WARNING: power cord before attempting to remove the system controller board.
  • Page 12 ......STEP 3 PRESS DOWN ON THE TABS TO OPEN AND LOWER THE REAR COVER. STEP 4 LOOSEN THE THUMBSCREWS AND REMOVE THE SYSTEM CONTROLLER BOARD.
  • Page 13 ......STEP 5 REMOVE A BLANK PLATE COVERING EITHER INTERFACE CONNECTOR SLOT. 1 Blank Plate 2 Mounting Posts (not used) 3 Retaining Bracket 190287-001 - 06/01/95 - - Saved by IDC - - Rev # 2 - File Name EXFX_US6.DOC...
  • Page 14 ......STEP 6 A. VERIFY THE CORRECT PLACEMENT OF JUMPERS ON THE SERIAL BOARD: P1 HAS A JUMPER. P2 DOES NOT HAVE A JUMPER.
  • Page 15 ......STEP 7 REINSTALL AND SECURE THE CONTROLLER BOARD AND CLOSE THE REAR COVER. 1 Thumbscrews 2 System Controller Board 3 Rear Cover 190287-001 - 06/01/95 - - Saved by IDC - - Rev # 2 - File Name EXFX_US6.DOC...
  • Page 16 ......STEP 8 RECONNECT ALL CABLES BUT DO NOT APPLY POWER. 190287-001 - 06/01/95 - - Saved by IDC - - Rev # 2 - File Name EXFX_US6.DOC...
  • Page 17 ......STEP 9 ATTACH ONE END OF THE INTERFACE CABLE TO THE SERIAL BOARD AND ATTACH THE OTHER END TO THE DECLASERFAX'S SERIAL PORT.
  • Page 18 ......STEP 10 190287-001 - 06/01/95 - - Saved by IDC - - Rev # 2 - File Name EXFX_US6.DOC...
  • Page 19 ......A. PLUG THE TELEPHONE CABLE INTO THE DECLASERFAX'S PSTN PORT. The telephone cable connects the DEClaserFAX to the public telephone network.
  • Page 20 ......STEP 11 PLUG IN THE PRINTER AND TURN IT ON (I). The DEClaserFAX requires a nominal 9-V DC supply at 132 mA.
  • Page 21 ......CAUTION: DO NOT push the yellow Reset button on the DEClaserFAX. If you push the button, turn the printer off then on to clear the reset.
  • Page 22 ......STEP 12 TEST THE HARDWARE INSTALLATION. 1. Using the printer's control panel, press the Menu key. The printer is off-line and in menu mode.

  • Page 23: After Installation

    ......2. Check that the P1 jumper on the serial board is placed correctly. The P1 jumper enables power so the jumper must be inserted.
  • Page 24 ......If the printer can receive faxes but can not send Note: them, the problem is most likely to be with the fax utility software.

Table of Contents