Gtec ZS110 User Manual

Gtec ZS110 User Manual

On-line ups
Hide thumbs Also See for ZS110:

Advertisement

USER MANUAL

On-Line UPS
Model ZS110
6000VA-10000VA
Uninterruptible Power Supply System
1

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the ZS110 and is the answer not in the manual?

Questions and answers

Summary of Contents for Gtec ZS110

  • Page 1: User Manual

    USER MANUAL On-Line UPS Model ZS110 6000VA-10000VA Uninterruptible Power Supply System...
  • Page 2: Table Of Contents

    Contents 1. Brief introduction 1Brief introduction..............1-5 1.1 System and model description 1.1 System and model description ............ The On-Line-Series is an uninterruptible power supply incorporating 1.2 Description of commonly used symbols ........double-converter technology. It provides perfect protection specifically for 1.3 Appearance ................
  • Page 3: Description Of Commonly Used Symbols

    1.2 Description of commonly used symbols The following symbols will be used in this manual and may appear during the course of your practical applications. Therefore, all users should be familiar with them and understand their meanings. Notation and Explanation Notation Explanation Notation...
  • Page 4: Product Specification And Performance

    1.4 Product specification and performance ●General specification Frequency Input(full load) Output Dimensions Weight Power Rating Model (Hz) (W*L*H)mm (kg) Voltage Current Voltage Current (176-276)VAC 31max 220V/230V 27A 260X560X717 6KVA/4.8KW 50/60 (176-276)VAC 31max 220V/230V 27A 260x533x501 17.5 6KVA/4.8KW 50/60 (176-276)VAC 50max 220V/230V 45A 260X560X717 10KVA/8KW 50/60 (176-276)VAC 50max 220V/230V 45A 260x533x501 19.5...
  • Page 5: Safety Instruction

    2. Safety Instruction 3. Installation ●Even if the interruptible Power System (UPS) is not connected to utility 3.1 Unpacking and inspection power, the output socket of the UPS may still present 220V/230V output 1) Unpack the packaging and check the package contents. The shipping voltage.
  • Page 6: Operating Procedure For Connecting The Long Backup Time Model Ups With The External Battery

    12) If it is necessary to connect the inductance load such as a monitor or a 3) For 10K (S)/3C10KS UPS, it is recommended to select the UL1015 laser printer to the UPS, the start-up power should be used for 8AWG (10mm2) wire or other insulated wire which complies with AWG calculating the capacity of the UPS, as its start-up power consumption Standard for the UPS input and output wirings.
  • Page 7: Parallel Operation

    3) Connect the output wires of each UPS to an output breaker panel first, and then connect the wiring to the load via the breaker panel. 1) A DC breaker must be connected between the battery pack and the 4) The parallel UPS must be equipped with battery individually. UPS.
  • Page 9: Operation And Operating Mode

    4. Operation and Operating mode LED will be turned on. The UPS is working in Bypass mode. 3) Upon completion of the above to turn it off, output of electric current of It is easy to operate the equipment, with no previous training. You just need the UPS is still present.
  • Page 10 utility power indicator blinks at the same time, it shows that the utility power is abnormal. The load/battery capacity indicators will be turn on in accordance with the battery capacity. Please note that the load/battery capacity indicator in normal mode will indicate the battery capacity in battery mode.
  • Page 11 disconnect to the ground for protection. 2. When operating in bypass mode, the UPS beeps every 2 minutes, If the “Function” key is pressed for more than 5 seconds, the alarm will not beep(silence function). Press the “Function” key more than 5 seconds again to resume the alarm function.
  • Page 12: Battery Maintenance

    5. Battery maintenance Pin number Function description Input ●This series UPS only requires minimal maintenance. The battery used for Output standard models is valve regulated sealed lead-acid maintenance free Ground battery. These models require minimal repairs. The only requirement is to charge the UPS regularly in order to maximize the expected life of the 2) User enables to monitor and manage the UPS through installed the battery.
  • Page 13: Notes For Battery Disposal And Battery Replacement

    7.Troubleshooting 6. Notes for battery disposal and battery replacement Problem Possible cause Solution 1) Before disposing batteries, remove conductive articles such as necklace, Make sure the UPS is not wrist watches and rings. overloaded; the air vents are not The 1# Fault LED blocked and the ambient 2) If it is necessary to replace any connection cables, please purchase the The UPS...
  • Page 14: Appendix 1 Description Of Display Panel

    Appendix 1 Description of Display panel 7.Troubleshooting Problem Possible cause Solution Check the battery. If the battery is damaged, replace Battery LED flashes Battery low the battery immediately and ensure that the battery breaker is in “ON” position. The utility power is normal, but the UPS AC input breaker in Set the input breaker in “ON”...
  • Page 15: Appendix2 Indicator And Alarm

    Appendix 1 Description of Display panel Appendix2 Indicator and alarm Appendix 1 Table Description of indicators LED indicators Operating status Audible alarm Color Indicator Description When the indicator on, it shows that Fault indicator 0%--25%Load ● ● ● none the UPS in abnormal condition. Orange Load/battery capacity indicator Show the capacity of load/battery:...
  • Page 16: Chapter Operation (Lcd Model)

    8 Chapter Operation (LCD model) LED indicators 8.1 Operation Display Panel Operating status Audible alarm Sustained ● ↑ BUS voltage fault ● ↑ beep Beep once ● ↑ ↑ Charger or battery fault every sec Beep once ↑ Fan failure ●...
  • Page 17: Operation Mode

    8.2 Operation Mode 2) If load is more than 105 percent, the buzzer beeps twice every second, meanwhile, the warning icon blinks every second too, reminding that UPS Operation Mode contains normal mode, battery mode and bypass you have been overloaded. You should get rid of some unnecessary loads mode.
  • Page 18 3) The other four display pages are load percent page, actual load page, input information page and the maximum temperature page. Notes: When operating in bypass mode, the backup function of the UPS is not available and the power used by the load is directly from the utility power via internal EMI filter.
  • Page 19: Operating Instructions

    When a warning occurred, the fault icon blinks every second, and users can indicate that the UPS is working in battery mode. switch to the alarm display page shown as the figure 8-6 to check the 2. Powering down the UPS warning code.
  • Page 20: Checking Ups Function

    8. 4Checking UPS function 8 Chapter Operation (LCD model) 8.5 Troubleshooting Every time when conducting field maintenance, please check the regular In the event of an UPS fault, shoot the trouble according to Table8.5-1. If function of the UPS, including: the fault still persists, please contact our customer service center.
  • Page 21 8 Chapter Operation (LCD model) Faults Possible Fault/ Faults Solution cause Warning Fault icon Alarm Possible Fault/ Solution code cause Warning Fault icon Alarm Beep Internal Please contact the code constantly continuously fault. distributor or Service center Blink once Reduce the member of Beep Overload Beep...

Table of Contents