Black & Decker BDPS200 Original Instructions Manual page 10

ENGLISH
Assembly
Warning! Before assembly, make sure that the tool is
switched off and unplugged.
Attaching the side fill canister (fig. A)
The side fill canister is designed so it will only fit one way
round.
Align the side fill canister (6) below the pick up tube (19)
u
with the lid (7) to the left.
Push the side fill canister (6) firmly into place.
u
Tighten the locking ring (20) by turning it clockwise.
u
Note: Ensure that the locking ring is tight and that the side fill
canister is firmly secured in place.
Aligning the pickup tube (fig. B1 & B2)
The pickup tube can be aligned in the direction that you will be
doing the most spraying to help minimize the amount of times
that you will have to refill the canister.
If you are spraying at an upward angle or straight on,
u
position the pickup tube (fig. B) toward the back of the
canister.
If you are spraying at a downward angle, position the
u
pickup tube (fig. C) toward the front of the canister.
This will ensure you spray as much material as possible
before you need to refill.
Attaching and removing the spray nozzels (fig. C
& D)
To attach the green fan spray nozzle: (Where supplied)
Turn the nozzle (10) clockwise onto the spindle for 6 - 8
u
full turns.
Push in the nozzle (10) and continue to turn it clockwise
u
untill it is fully seated.
Note: Ensure the spray nozzle is completely threaded on by
hand only. If it is not fully seated in can leak or damage the
nozzle.
To remove the green fan spray nozzle: (Where supplied)
Push in the nozzle (10) and turn it anticlockwise.
u
To attach the blue cone spray nozzle:
Turn the nozzle (11) clockwise onto the spindle until it is
u
fully seated.
Note: Ensure the spray nozzle is completely threaded on by
hand only. If it is not fully seated in can leak or damage the
nozzle.
To remove the blue cone spray nozzle:
Turn the nozzle (11) anticlockwise.
u
10
(Original instructions)
Filling the canister (fig. E
Check to make sure that the side fill canister (6) is com-
u
pletely screwed onto the sprayer.
Lay the sprayer on its side with the canister side lid facing
u
up.
Pour the properly thinned and strained material to be
u
sprayed into the side fill canister.
Note : Use a mixing bucket to pour material from the original
material container into the side fill canister.
Clean any residual liquid from the threads or sides of the
u
canister and sprayer.
Starting the threads evenly, screw the lid completely
u
onto the side fill canister. Check the lid to make sure it is
threaded on squarely and completely before picking up
the sprayer.
Use
Switching on and off
The sprayer is turned on and off with the spray trigger.
To turn the sprayer on, squeeze the spray trigger (2).
u
To turn the sprayer off, release the spray trigger (2).
u
Warning! Never point the sprayer at any part of the body.
Never pull the trigger while adjusting the spray setting.
Selecting the spray pattern (fig. F & G) (BDPS400 &
BDPS600 Only
This sprayer is supplied with 2 nozzles which are capable of
producing 3 spray patterns. .
Green nozzle - Horizontal Flat Jet - Apply up and down
a surface.
Green nozzle - Vertical Flat Jet - Apply side to side.
Blue nozzle - Circular Jet - for corners, edges and narrow
surfaces.
To select the cone spray pattern, fit the blue cone nozzle.
u
To select the horizontal fan spray pattern, fit the green fan
u
spray nozzle and turn the nozzle so so the jet indicator
tabs (21) are in the vertical position (fig. F).
To select the Vertical fan spray pattern, fit the green fan
u
spray nozzle and turn the nozzle so so the jet indicator
tabs (21) are in the horizontal position (fig. G).
Warning! Never point the sprayer at any part of the body.
Never pull the trigger while adjusting the spray setting.