Table of Contents
Advertisement
Flushing the sprayer (fig. Q & R)
Disconnect the sprayer from the power supply.
u
Unscrew the lid from the side of the canister and pour any
u
remaining liquid back into the original container (fig. R).
Pour a small amount of the appropriate cleaning solution
u
into the canister.
Warm soapy water for water based materials.
t
Manufacturers recommended cleaning solution for oil
t
based materials.
Replace the lid (7) on the canister (6) securely and vigor-
u
ously shake the sprayer.
Unscrew the lid (7) from the side of the canister and
u
properly dispose of cleaning solution.
Refill the canister with a small amount of new cleaning
u
solution. Screw lid securely on canister.
Reattach the sprayer to the motor unit, plug in the cord
u
and turn on the power unit.
Switch the quick clean lever (1) from clean to paint. (fig.Q)
u
Spray the cleaning solution through the sprayer onto scrap
u
material for 5 seconds.
Cleaning the sprayer (fig. S - X)
Disconnect the sprayer from the power supply.
u
Remove the side fill canister (6) and unscrew the side lid
u
(7). Remove the pickup tube (19) and o-ring (23) from the
sprayer. Clean the parts with the cleaning brush (14) in the
appropriate cleaning solution (fig. S).
Remove the front housing of the sprayer, by pressing
u
down on the release button (15) and pulling the front
housing off of the sprayer (fig. T).
Remove the piston (27) and spring (26) (fig. U).
u
Remove the spray nozzle (10 / 11), by turning counter-
u
clockwise, then remove the atomizer (24) (fig. U).
Clean the spray nozzle (10 / 11), pickup tube (19) and filter
u
(25), atomizer (24), piston (27) and spring (26) with the
cleaning brush (14) in the appropriate cleaning solution
(fig. T).
Thoroughly clean the inside of the piston chamber (28)
u
with the cleaning brush (14) (fig. V)
Important : Be sure to remove all material from inside
of piston chamber. A small amount of material that is not
removed with the cleaning brush can harden over time and
interfere with the movement of the piston causing damage to
the sprayer.
Switch the quick clean lever (1) from clean to paint.
u
Thoroughly clean the inside of the intake (30) and return
u
(29) openings with the cleaning brush (fig. W).
Important : Thoroughly clean the smaller vent hole (31), with
a pin or paper clip (fig. X).
Dry all parts thoroughly.
u
Properly dispose of cleaning solution.
u
Reassemble sprayer.
u
(Original instructions)
Reassembling the sprayer (fig. Y & Z)
Slide the spring (26) onto the front of the piston (27).
u
Insert the piston and spring into the front housing.
u
Pressing down on the release button (15), insert the front
u
housing with piston, into the sprayer until the release but-
ton pops into place.
Place a few drops of oil through the cylinder opening. In-
u
sert the atomizer valve (24) into the front housing. Thread
the spray nozzle (10 / 11) onto the front housing and hand
tighten.
Using the oil lubricant provided, place a few drops of
u
oil down the intake (30) and return (29) openings of the
sprayer.
Rotate the quick clean lever (1) from paint to clean and
u
back 3 times after oiling.
Insert the pickup tube (19) into the intake opening (30) on
u
the sprayer.
Re-fit the side fill canister.
u
Cleaning the power unit
Turn the power unit off, unplug the cord and disconnect
u
the sprayer from the motor unit.
Use only mild soap and damp cloth to clean the power
u
unit.
Warning! Never let any liquid get inside the power unit.
Warning! Never immerse any part of the power unit into a
liquid.
Mains plug replacement (U.K. & Ireland only)
If a new mains plug needs to be fitted:
Safely dispose of the old plug.
u
Connect the brown lead to the live terminal in the new
u
plug.
Connect the blue lead to the neutral terminal.
u
Connect the green/yellow lead to the earth terminal.
u
Warning! Follow the fitting instructions supplied with good
quality plugs. Recommended fuse: 13A.
Protecting the environment
Z
Separate collection. This product must not be
disposed of with normal household waste.
Should you find one day that your Black & Decker product
needs replacement, or if it is of no further use to you, do not
dispose of it with household waste. Make this product avail-
z
able for separate collection.
Separate collection of used products and packaging
allows materials to be recycled and used again.
Re-use of recycled materials helps prevent environ-
mental pollution and reduces the demand for raw
materials.
ENGLISH
13
Hide quick links:
Advertisement
Table of Contents
