Table of Contents
Advertisement
Advertisement
Table of Contents
Related Manuals for Merlin MT600
Summary of Contents for Merlin MT600
-
Page 2: Table Of Contents
Start by Reading These Important Safety Instructions Failure to comply with the following instructions may result in serious personal injury or property damage. • Read these instructions carefully • The garage door opener is designed and tested to offer reasonable safe service provided it is installed and operated in strict accordance with the instructions in this manual. -
Page 3: Door Types
DOOR TYPES A. One-Piece Door with Horizontal Track Only B. One-Piece Door with Horizontal and Vertical Track – Special door arm (E, The Chamberlain Arm™) and The Protector System (29 (9)) are required. See your dealer. C. Sectional Door with Curved Track – See 20B – connect door arm. -
Page 4: Before You Begin
BEFORE YOU BEGIN: 1. Look at the wall or ceiling above the garage door. The header bracket must be securely fastened to structural supports. 2. Do you have a finished ceiling in your garage? If so, a support bracket and additional fastening hardware (not supplied) may be required. - Page 5 Insert Chain/Belt into Rail & Assemble Header Sleeve Slide pulley bracket (1) and inner trolley (2) into back (opener end) of rail assembly (3), be sure to insert pulley bracket as shown with arrow (4) pointing toward front (header end) of rail (5). Push bracket toward front (header end ) of rail (5).
- Page 6 INSTALLATION SECTION Wear protective goggles when working overhead to protect your eyes from injury. Disengage all existing garage door locks to avoid damage to the garage door. To avoid serious personal injury from entanglement, remove all ropes connected to the garage door before installing the opener.
-
Page 7: Connect Electric Power
Position the Opener NOTE: A 25mm (1") board (1) is convenient for setting an ideal door-to-rail distance (unless headroom is not sufficient). Raise the opener onto a stepladder. Open garage door. Place a 25mm (1") board (1) laid flat on the top section of door near the centerline as shown. -
Page 8: Fasten Door Bracket
Fasten Door Bracket If you have a canopy garage door, a door arm conversion kit is required. Follow the installation instructions included with the replacement door arm. Exercise care in removing and assembling arm conversion kit. Keep fingers away from the sliding parts. NOTE: Horizontal and vertical reinforcement is needed for lightweight garage doors. - Page 9 Install Door Control (optional accessory) Locate door control where the garage door is visible, away from door and door hardware and out of the reach of children. Mount at least 1,5 m (5 feet) above the floor. Serious personal injury from a moving garage door may Push Bar Cover result from misuse of opener.
-
Page 10: Programming The Code
Program your Opener & Remote Activate the opener only when door is in full view, free of obstruction and properly adjusted. No one should enter or leave garage while door is in motion. Do not allow children to operate push button(s) or remote(s). Do not allow children to play near the door. - Page 11 NOTE: Tightening the wall mount screws will reduce clearance between bracket and wall. A 3-channel (3-button) remote control may be used for up to three Merlin garage door operators. Program the Receiver to Match Additional Remote Control Code Using the orange “LEARN” Button: 1.
-
Page 12: Adjustment
Using the Motion Detecting Control Panel (optional accessory) Press the push bar (1) to open or close the door. Press again to stop the door. Light feature Press the light button to turn the opener light on or off. It will not control the opener lights when the door is in motion. -
Page 13: Install The Protector System (Optional)
Setting the Force The force, as measured on the closing edge of the door, should not exceed 400N (40kg). If the closing force is measured to more than 400N, the Protector System must be installed See step 29. The force setting regulates the amount of power required to open and close the door. -
Page 14: Special Features
Special Features Flashing light connection The flashing light can be installed anywhere. Connect light leads to quick connect terminals 1 and 2. Terminal 2 is 180s ground. 120s Timer to close function can be enabled by turning the dial to the required time. If the protector system is installed the timer to close should be set after the protector system is installed. -
Page 15: Replacement Parts
REPLACEMENT PARTS 171A28 12C810 83A11 41B4101-1 41A5800 12B374 41B4494-1 7423CR3 210C42 183D177 183D178 178B34 8423CR3 12C855 12C778 8430CR3 8023CR3 8025CR3 41B4103 41A5414-4 8030CR3 41A2828 4A1008 1/2” 41A5844 (2.3m) 109A46 1” 41A5844-1 (2.5m) 41A5844-2 (3.0m) 12B380 31D537... -
Page 16: Care Of Your Opener
REPLACEMENT PARTS 171A543 Belt 41A4371-3 Chain 41A4371-2 28A95 158A49 171A498 26B72 216A206 41C589 41B5348 171A479 37D117-2 41B4375-3 41C5392 171A315 41B5351-5 171A384-8 41A5696-2c (60kg) 41C5350-5 (60kg) 41A5696-4c (100kg) 41C5350-2 (100kg) 171A384 41D701-2 (60kg) 41D605 (100kg) 171A545 108D56 41D188 171A320 CARE OF YOUR OPENER When properly installed, opener will provide high performance with a minimum of maintenance. -
Page 17: Having A Problem
HAVING A PROBLEM? 1. Opener doesn't operate from either door control or remote: • Does the opener have electric power? Plug lamp into outlet. If it doesn't light, check the fuse box or the circuit breaker. (Some outlets are controlled by a wall switch.) •... -
Page 18: Operation Of Your Opener
2. when the power is briefly interrupted; 3. when the opener is activated. SPECIAL NOTE: Merlin strongly recommends that the The light turns off automatically after 2-1/2 minutes. Bulb size protector system be installed on all garage door openers. -
Page 19: Warranty
C Connection to any garage door outside the specifications set out in the owners manual; D Any modification or repair to the Unit carried by a person not authorised to do so by Merlin Garage Openers Limited; E Radio or any other electrical or electronic interference;... - Page 20 NOTES: 114A3354 ©, 2006...