On-Disc Timer Programming - JVC DR-M100S Instructions Manual

On-Disc Timer Programming

On-Disc Timer Programming is a function used with discs that are
especially intended for a specific program. The disc is then
programmed for a program you always watch every day or every
week. Since older programs are automatically overwritten, a single
disc can be used without worrying about how much recording
capacity remains. You can program each disc to timer record as
many as 8 programs up to 30 days in advance.
●
Make sure that the unit's built-in clock is set properly.
●
Turn on the TV and select an input mode such as EXT1.
●
Load a DVD-RAM or DVD-RW (VR mode) disc for
programming.
ATTENTION:
●
On-Disc Timer Programming is possible only with the disc for
On-Disc Timer Programming.
●
If data is recorded on a disc for On-Disc Timer Programming
using a unit from another manufacturer, On-Disc Timer
Programming may not function properly.
PROG
DVD A
FGD E
Selection Keys ( )
ENTER
To Make The Disc For On-Disc Timer Programming
1
Press PROG to access
the Program Check
screen.
2
Press selection keys to
select ADISC TIMER
PRGMB, then press
ENTER.
●
When some programs
are recorded on the disc,
a caution message
appears. To backup the recorded programs, press ENTER, and
perform dubbing to other devices.
●
When On-Disc Timer Programming has already been made on
the disc, press selection keys to select ANEW TIMER
PROGRAMB, then press ENTER.
3
Press selection keys to
set the desired date
(ADATEB), then press E.
4
Press selection keys to
set the desired start time
(ASTARTB), then press E.
● Each press of F G
increases/decreases the
start time in 1-minute
interval.
●
To increase/decrease the start time in 30-minutes interval,
press and hold F G.
5
Press selection keys to set the desired stop time (ASTOPB),
then press E.
● Each press of F G increases/decreases the stop time in 1-
minute interval.
●
To increase/decrease the stop time in 30-minutes interval,
press and hold F G.
6
Press selection keys to set the desired channel (ACHB), then
press E.
7
Press selection keys to set ADAILY/WEEKLYB, then press E.
●
For details on ADAILY/WEEKLYB setting, refer to "Daily/Weekly
Recording Function" (A pg. 37).
8
Set the other recording
options as required.
●
"Recording Mode"
(A pg. 34)
●
"Modify Title Name"
(A pg. 46)
9
Press ENTER to access
the Program
Confirmation screen.
10
Press ENTER to
complete the timer programming.
●
To program another timer using "To Make The Disc For On-
Disc Timer Programming", repeat steps 1 - 10.
11
Press DVD A to turn off the power.
●
is displayed on the front display panel.
● To disengage the timer mode, press DVD A again.
Cable Box or DBS Receiver Users
To timer record a satellite broadcast using On-Disc Timer
Programming:
A Perform On-Disc Timer Programming.
●
Set the channel to the external input (AL-1B or AF-1B)
connected to the cable box or DBS receiver.
B Set the cable box or DBS receiver to the appropriate channel
for recording.
●
Leave the cable box or DBS receiver's power on.
TIMER RECORDING
PROGRAM CHECK
DATE START STOP CH DAILY/WEEKLY REC MODE
++++++++++++++++++ NEW TIMER PROGRAM ++++++++++++++++++
DISC TIMER PRGM
EXIT OK
SELECT WITH [CURSORS]
THEN PRESS [ENTER]
SELECT
PROG
DISC TIMER PRGM
DATE START STOP
10/07/03 THU - - : - - - - - - : - - - -
DAILY/WEEKLY REC MODE
WEEKLY SP
EXIT CONFIRM
SET TIMER PROGRAMING WITH [CURSORS]
THEN PRESS [ENTER]
SELECT
PROG
DISC TIMER PRGM
DATE START STOP
10/07/03 THU - - : - - - - - - : - - - -
DAILY/WEEKLY REC MODE
WEEKLY
SP
EXIT CONFIRM
SET TIMER PROGRAMING WITH [CURSORS]
THEN PRESS [ENTER]
SELECT
PROG
39
EN
CH
- -
NAME
CH
- -
NAME