Page 2
électrique, d’incendie ou de blessure n’effectuer que les réparations indiquées dans le mode d’emploi à moins d’être qualifi é pour en effectuer d’autres. Pour toute réparation faire appel à une personne compétente uniquement. PMW-EX1R...
Page 3
Batterien nur durch den vom Hersteller empfohlenen Kasser batteriet i henhold til gjeldende avfallsregler. oder einen gleichwertigen Typ ersetzen. Wenn Sie die Batterie entsorgen, müssen Sie die Gesetze der jeweiligen Region und des jeweiligen Landes befolgen. 1 (P) PMW-EX1R...
Outline of Replacement Procedures ......2-1 (E) 3-5. List of Error Numbers on the LCD Display ....3-10 (E) 2-2. Replacement Procedures ...........2-2 (E) 2-2-1. Lithium Battery ..........2-2 (E) 2-2-2. Case (Bottom) L/R and Front Panel Assembly ............2-2 (E) 1 (E) PMW-EX1R...
Related manuals The following manuals are available in this model. If this manual is required, please contact your local Sony Sales Offi ce/Service Center. . Operating Instructions (Supplied with unit) This manual is necessary for application and operation of this unit.
AUTO INTMIC CH-1 HDV/DV: i.LINK connector (IEEE1394, S400) (4P) MANUAL START/ STOP AUTO INTMIC CH-2 MANUAL PMW-EX1R RELEASE _ EXT VIEW _ Signal Specifi cations TPB_ Strobe on receive, data on 1 SDI OUT: BNC type transmit B (_)
Page 10
+11 to +17 V dc BATT (+) COMMON_V BAT_SCL ZOOM GND: WIDE 1.66V: STOP BAT_SDA 3.33V: TELE BATT_ID_DATA COMMON+V 3.33V BATT (_) COMMON 1.66V GND: ON OPEN: OFF GND: ON OPEN: OFF SW COMMON O FRAME GND 1-2 (E) PMW-EX1R...
The video signal then receives the pedestal control, knee compensation, gamma correction and white/black clip processing. The video signal fi nally enters the baseband processing IC (IC600). The pixel number conversion processing from 1920/1080 to 1440/1080 or 1280/720 is also performed inside IC200. 1-4 (E) PMW-EX1R...
Page 13
Furthermore, dual channel USB host signals output from USB host controller (IC2300) are connect to the EC-68 board through fi ne coaxial cables just as with the PCI-Express signals. IC2300 is controlled by PCI bus from IC1600. 1-5 (E) PMW-EX1R...
Page 14
. SEL (IC204, IC205)/AMP (IC206, IC207) are a signal selector and buffer amplifi er to perform AGC link. DAP-41 Board (Audio block) The DAP-41 board is comprised of two pieces of the Audio Codec IC and the IC202, IC203. (RTC is also built on this board, but the explanation has been omitted here.) 1-6 (E) PMW-EX1R...
Page 16
(X2900). FLASH ROM (IC2908), SDRAM (IC2909), and EEPROM (IC3205) are mounted as the periph- eral ICs. It performs the system control through serial communication with IC500 of the camera block system, IC600 of the video signal system, and IC1600 of the media recording/playback system. 1-8 (E) PMW-EX1R...
Page 17
(6) Power system control IC1001 on the RE-273 board checks that the power switch on the PMW-EX1R is turned ON, and turns on the system controller of IC2900. After that, it controls the power for each circuit block according to the system controller.
Page 18
When the power switch of the camera is turned off, the POWER SUPPLY MICON (power supply μ-processor: IC1001) enters the Sleep mode in order to save the power by minimizing the detection circuit of the camera power switch. 1-10 (E) PMW-EX1R...
Page 19
This helps provide detailed infor- mation about the battery, including whether the battery is damaged or how long the life is, in order to provide optimal operations. 1-11 (E) PMW-EX1R...
Torque driver (6 kg.cm) (0.6 N.m) 7-432-114-11 Locking compound 200 g For preventing screw from being loosened 7-651-000-10 Sony (SGL-601) 50 g grease Lubricant * : This cable is supplied with PMW-EX1R. , ...
7. Attach the cover on the USB maintenance connector. When the PMW-EX1R is connected to the computer for the fi rst time, the driver software will need to be installed into the computer. For more details, check the readme fi le that comes with the upgrade software.
1-6. Recommended Replacement Parts This section describes the recommended replacement parts and recommended replacement time. Part name Sony part No. Recommended replacement timing Eye cup 4-164-856-01 Check for deformation and deterioration from time to time. Replace it as necessary. Lens hood...
The fuse is an essential part for safe operation. Replace the components with Sony parts whose part numbers appear in the manual published by Sony. If the components are replaced with any parts other than the specifi ed ones, this may cause a fi re or electric shock.
1-8-4. Description of Number Seal on the Prism The number seal is put in the prism unit, the serial number of prism unit. Every prism unit has its own number called prism serial number. 1-16 (E) PMW-EX1R...
. The ordinary soldering iron can be used but the iron tip has to be applied to the solder joint for a slightly longer time. The printed pattern (copper foil) may peel away if the heated tip is applied for too long, so be careful. 1-17 (E) PMW-EX1R...
1. Insert the fl exible card wire fi rmly as far as it will go, with its insulated side facing front. 2. Close the latch of the connector in the direction of arrow D to lock. Disconnecting Connecting Flexible card wire Flexible card wire Insulated side Insulated side Latch Connector Latch Connector 1-19 (E) PMW-EX1R...
Type D Type D Connecting Insert the connector of the coaxial cable with connector fi rmly as far as it will go. Type C Type D Coaxial cable with connector Connector Coaxial cable with connector Connector 1-20 (E) PMW-EX1R...
(bottom) L in the direction of the arrow. 4. Remove the case (bottom) R. Be careful not to drop or damage the USB cover. : M2 x 6 (Black) USB cover : M2 x 4 (Black) 2-2 (E) PMW-EX1R...
Page 31
Front panel assembly When installing the front panel assembly, check if the position of the slide switch (S2) on the SW-1478 board matches the position of the SHUTTER knob. Front panel assembly SW-1478 board Slide switch Shutter knob 2-3 (E) PMW-EX1R...
3. Disengage the two claws on the front of the (upper) handle cover (upper) assembly fi rst. Then assembly remove the rear of the handle cover (upper) assembly from the EVF assembly. Claws Rubber SW key Be careful not to drop the rubber SW key. 2-4 (E) PMW-EX1R...
(S503) on the DR-644 board matches the position of the knob (LCD B.LIGHT). Knob (LCD B.LIGHT) Slide switch S503 DR-644 board : M2 x 2 (black) 2-5 (E) PMW-EX1R...
Page 34
(30 core) connector, do not attempt to remove by pulling the cable. Be sure to hold the connector to remove. DPR-311 board CN700 9. Reinstall the handle assembly by reversing the steps of removal. Coaxial cable with connector 2-6 (E) PMW-EX1R...
Page 35
9. Remove the four screws of d, and remove the AU-326 board. 10. Reinstall the DAP-41 board and AU-326 AU-326 board board by reversing the steps of removal. HN-360 board CN100 : M2 x 3 (silver) 2-7 (E) PMW-EX1R...
“Handle Assem- bly” removal. 2. Remove the two screws of a and one screw of b, and remove the inside panel assembly. Inside panel assembly a : M2 x 4 (silver) b : M2 x 4 (silver) 2-8 (E) PMW-EX1R...
Page 37
7. Disconnect the harness from the connector (CN2) on the VIF-46 board. Tape VIF-46 board 8. Reinstall the inside panel assembly/outside panel assembly by reversing the steps of removal. Be careful that no harness should be caught. Harness 2-9 (E) PMW-EX1R...
(CN1) on the RE-272 board. 6. Disconnect the CN-3273 (fl exible board) RE-272 board (CN1) from the connector (CN101) on the ASW-68 board. CN-3273 board 7. Reinstall the rear panel assembly by reversing the steps of removal. 2-10 (E) PMW-EX1R...
5. Remove the two screws, and remove the express card assembly in the direction of the arrow. Express card assembly 6. Reinstall the express card assembly by revers- ing the steps of removal. M2 x 3 (silver) 2-11 (E) PMW-EX1R...
10. Disconnect the CN-3258 (fl exible board) CN200 from the connector (CN200) on the RE-272 board, and remove the RE-272 board. CN-3258 board Harness 11. Reinstall the RE-272 board and RE-273 board by reversing the steps of removal. Inside button holder 2-12 (E) PMW-EX1R...
7. Remove the three screws of e, and remove the i-Link holder. i-Link holder CN-3273 board : M2 x 3 (silver) : M2 x 2 (black) : M2 x 3 (silver) 2-13 (E) PMW-EX1R...
Page 42
: B2 x 3 (silver) nector on the TX-131 board. 17. Remove the four screws of k, and remove the TX-131 board. Coaxial cable TX-131 board 18. Reinstall the battery case and the TX-131 board by reversing the steps of removal. 2-14 (E) PMW-EX1R...
DPR-311 board. DPR-311 board 8. Remove the DPR-311 board. CN-3259 board 9. Reinstall the DPR-311 board by reversing the steps of removal. Coaxial cable with connector Flexible boards of prism assembly 2-15 (E) PMW-EX1R...
HN-360 board 5. Disconnect the SWC-50 board from the connector (CN104) on the DAP-41 board. 6. Disconnect the HN-360 board from the connector (CN2) on the AU-326 board. DAP-41 board CN104 SWC-50 board AU-326 board HN-360 board 2-16 (E) PMW-EX1R...
4. Remove the one screw of b and two screws of c, and remove the case R. 5. Reinstall the case R by reversing the steps of removal. a : M2 x 4 (black) b : M2 x 4 (black) c : M2 x 3 (silver) 2-17 (E) PMW-EX1R...
ND fi lter are aligned with the dowels. . When reinstalling the ND fi lter, loosely fi x the three screws, and then fully tighten them while paying attention not to deform the ND fi lter. 2-18 (E) PMW-EX1R...
4. Reinstall the DR-644 board by reversing the Slide switch steps of removal. DR-644 board When installing the DR-644 board, check if Knob the position of the slide switch (S1) on the DR-644 board matches the position of the knob. 2-19 (E) PMW-EX1R...
4. Remove the speaker holder sheet, and remove holder sheet the speaker harness from the slit of the speak- er holder. Speaker harness 5. Remove the speaker from the speaker holder. 6. Reinstall the speaker by reversing the steps of removal. 2-20 (E) PMW-EX1R...
(CN4) on the KSW-55 board. 6. Disconnect the HN-361 board from the Control switch block connector (CN1) on the KSW-55 board. KSW-55 board 7. Reinstall the KSW-55 board and HN-361 HN-361 board board by reversing the steps of removal. 2-21 (E) PMW-EX1R...
7. Remove the microphone unit assembly in the direction of arrow “D”. Be careful not to hook or damage the har- nesses. 8. Reinstall the microphone unit assembly by reversing the steps of removal. Harness (KSW53-MA161) Harness (KSW53-RM213) Microphone unit assembly 2-22 (E) PMW-EX1R...
MA-183 board 10. Reinstall the microphone unit by reversing c : Tapping M2 x 5 (black) d : Tapping M2 x 5 (black) the steps of removal. When assembling, attach the MA CUSHION to the original place. 2-23 (E) PMW-EX1R...
DET-52 board and the DET44 fi t plate. 6. Remove the two screws of c, and remove the DET-52 board from the DET44 fi t plate. 7. Reinstall the DET-52 board by reversing the steps of removal. DET-52 board DET44 fit plate 2-24 (E) PMW-EX1R...
5. Remove the four screws and the LCD pack- M2 x 3 ing, and remove the 3.5-inch LCD assembly. (silver) LCD packing 6. Reinstall the 3.5-inch LCD assembly by reversing the steps of removal. LCD bezel Coaxial cable with connector 2-25 (E) PMW-EX1R...
Page 54
1. Separate the grip belt from the buckle, and remove the pad. (Fig. 4) 2. Pull it off the grip belt from the grip cover. (Fig. 4) 3. Install the new grip belt by reversing the steps of removal. (Fig. 4) START/STOP 2-26 (E) PMW-EX1R...
RPN CORRECT Operations regarding the RPN correction INFORMATION Information display on the particular PMW-EX1R and self-diagnostics The MAINTENANCE menu and the RPN CORRECT menu can be operated in the CAMERA mode. 3-1-3. Displaying the SERVICE Menu Jog dial MENU button To display the SERVICE menu, the following operations are needed.
Displays and move the vertical address of the RPN correction point indicator cursor Cursor Next Moves the RPN correction point indicator cursor to the next RPN point Cursor Prev Moves the RPN correction point indicator cursor to the previous RPN point 3-2 (E) PMW-EX1R...
Cancel Item10 Execute Executes self-diagnostic Item 10 Cancel Item11 Execute Executes self-diagnostic Item 11 Cancel Item12 Do not execute this item. Item13 Do not execute this item. Log Dump Execute Records the error log to media Cancel 3-3 (E) PMW-EX1R...
Audio I/F while playing back Diagnosis of the audio signal line (playback direction) from AVIT between display and media block signal processing IC to base band processing IC Item12 Do not execute this item. Item13 Do not execute this item. 3-4 (E) PMW-EX1R...
Page 59
Shows the number of trials of the self-diagnosis. Success Shows the number of internal successes of the self-diagnosis. Result Shows the result of the self-diagnosis. “0” means no problems. When a value other than “0” is displayed, check the details for each self-diagnostic item. 3-5 (E) PMW-EX1R...
Page 60
Display block diagnosis analyzes the following contents. (Ver.1.1 or later) Diagnosis description Error value Type 1/2 Note 0x01 Communication signal line -1: Connection error 1, 2 test of LCD 0x02 Communication signal line -1: Connection error 1, 2 test of COPRO (SAD) 3-6 (E) PMW-EX1R...
Page 61
Audio block diagnosis analyzes the following contents. Diagnosis description Error value Type 1/2 Note 0x02 Memory area check for -1: Memory read/write 1, 2 audio block comparison NG When an error occurs, it indicates that the hardware has a defect. 3-7 (E) PMW-EX1R...
Page 62
When an error is detected in the IIC communication test, it indicates a possible failure in the communication line or device. *: When an error is detected in the version matching test, upgrade again to a compatible version. Contact your local Sony Sales Offi ce/Service Center for information on versions. Item6: Power block diagnosis Power block diagnosis analyzes the following contents.
Executing Log Dump acquires the error log information and saves it to the active, writable media. Select Log Dump under the INFORMATION menu, and execute it with Execute. The process is complete when “Log Dump Done” is displayed as a result. Do not remove the media until Log Dump message appears. 3-9 (E) PMW-EX1R...
Internal error in the media block Repair the DPR-311 board or replace it. 4XXXX If multiple errors occur simultaneously The highest-priority error is displayed. When an error with a higher priority is cleared, the one with the next priority is displayed. 3-10 (E) PMW-EX1R...
For how to obtain the “ServiceNavi-EX”, contact your local Sony Sales Offi ce/Service Center. 4-2. Preparation . When adjusting the PMW-EX1R, use the AC adapter or a fully-charged battery pack. . When disconnecting the AC adapter or battery pack after the adjustment, turn off the power switch and wait for at least 10 seconds.
The V Saw menu enables the vertical Saw black shading correction (linear increase and decrease) level. V Para The V Para menu enables the vertical Parabola black shading correction (black level correction at the vertical center with respect to both ends) level. 4-2 (E) PMW-EX1R...
The White Shading correction is turned On automatically when the power is turned On. 2. Channel Select . The Channel Select menu enables selection of the channel (G-ch or B-ch or R-ch) to execute the H Saw, H Para, V Saw, and V Para white shading adjustments on. 4-3 (E) PMW-EX1R...
Page 68
2. Adjust H Saw, H Para, V Saw and V Para for the respective channels of G-ch, B-ch and R-ch until waveform on the waveform monitor becomes fl at. (H SAW) (H PARA) (V SAW) (V PARA) 4-4 (E) PMW-EX1R...
. The fl are adjustment can be performed only when there is a correct grayscale chart. . When there is no correct grayscale chart, adjust the values of R Flare, G Flare and B Flare to ?0. 4-5 (E) PMW-EX1R...
. Set up the camera as follows: Item Setting FOCUS RING FULL MF IRIS SW MANUAL MACRO SW FOCUS SW MANUAL ZOOM SW SERVO ND FILTER OFF (Clear) SHUTTER SW GAIN L (0 dB) WHITE BAL B (ATW) FULL AUTO 4-6 (E) PMW-EX1R...
Page 71
1. Set the lens iris to OPEN, set the ZOOM to TELE end and adjust the focus. 2. Move ZOOM from TELE end to WIDE end, and check that the lens remains in focus throughout the travel between TELE end and WIDE end. 4-7 (E) PMW-EX1R...
. Signal of the pixel located at the center of the crosshair cursor is replaced by black. . The Cursor setting is always turned Off when the power is turned On. 4-8 (E) PMW-EX1R...
. The Compensation Level menu is dedicated to display only and the cursor cannot be moved to this menu. 4-4-10. Executing Record . The Record menu enables the manual registration of RPN. . When Record menu is selected, the Execute and Cancel choices appear. In addition, selecting Execute starts the registration of RPN. 4-9 (E) PMW-EX1R...
* When RPN Record is attempted, if the RPN registration of a pixel fails at a specifi c address due to a problem with the small interval between the current and previous registered RPN spots, the screen shows the message “NG : Adjacent Pixel”. 4-10 (E) PMW-EX1R...
Therefore, specifi ed parts should be used in the case of replacement. 2. Standardization of Parts Some repair parts supplied by Sony differ from those used for the unit. These are because of parts common- ality and improvement. 3. Stock of Parts Parts marked with “o”...
Handle Cover and EVF Assembly 5-2. Exploded Views PMW-EX1R...
Page 77
3-285-383-03 s COVER CONNECTOR 3-288-585-02 s CASE, PANEL 3-288-586-02 s LID, PANEL 3-288-591-01 s SHEET, VF PROTECTION 3-302-492-01 s SPRING, COMPRESSION 3-657-657-02 s SCREW (M5) 3-878-256-03 s RUBBER SW KEY 4-164-591-01 s CABINET EVF 4-164-856-01 s EYE CUP 4-673-655-01 s SCREW +B PMW-EX1R...
Page 78
Handle Block 1 PTT2.6 x 6 PTT2.6 x 6 P2.6 x 4 PMW-EX1R...
Page 79
3-724-182-01 s NUT (SMALL JACK), M6 3-968-729-52 s SCREW (M2), LOCK ACE, P2 4-164-569-01 s SHOE REAR ACCESSORY 4-164-593-02 s SWITCH ZOOM 4-164-596-01 s LED-491 BRACKET 3-080-203-01 s SCREW (M2), LOCK ACE, P2 7-627-556-38 s SCREW +P 2.6X4.0 7-685-792-09 s SCREW +PTT 2.6X6 (S) PMW-EX1R...
Page 81
3-278-657-01 s CASE, MICROPHONE 3-278-658-01 s HINGE COVER LOWER 3-278-660-01 s MIC CUSION(R) 3-278-661-01 s MIC CUSION(L) 3-278-662-11 s HANDLE (MAIN) 3-278-668-01 s HINGE 3-284-538-01 s SHIELD SHEET(MIC) 3-968-729-52 s SCREW (M2), LOCK ACE, P2 4-164-597-01 s MA CUSHION PMW-EX1R...
Page 83
3-278-639-02 s JACK COVER 3-288-392-01 s WASHER (D), TRIPOD 3-604-795-01 s CAP BNC 3-701-439-21 s WASHER 3-968-729-52 s SCREW (M2), LOCK ACE, P2 4-164-565-01 s USB COVER 4-164-566-01 s CASE(BOTTOM)L 4-164-567-01 s CASE (BOTTOM)R 4-164-568-01 s LID LITHIUM BATERY PMW-EX1R...
Page 84
Outside Panel and Rear Panel 5-10 PMW-EX1R...
Page 85
4-164-730-01 s BRACKET DC JACK 4-164-731-01 s PANEL REAR 4-164-732-02 s BUTTON (REAR) PUSH 4-164-733-01 s RAIL (REAR) SLIDE 4-164-735-01 s SWITCH (REAR (L)) SLIDE 4-164-736-01 s SWITCH (REAR (H)) SLIDE 4-164-997-01 s CAPACITOR BRACKET 4-644-493-11 s ACE (M2.6), LOCK 5-11 PMW-EX1R...
Page 87
3-968-729-52 s SCREW (M2), LOCK ACE, P2 4-164-571-01 s SHEET RADIATION 1.5 C 4-164-598-01 s SHEET RADIATION BOTTOM 4-164-656-01 s SHEET RADIATION 1 A 4-166-648-01 s BATTERY CASE GASKET 4-170-734-01 s INSIDE BOTTOM GASKET 3-080-203-31 s SCREW (M2), LOCK ACE, P2 5-13 PMW-EX1R...
Page 89
4-164-627-01 s SHEET RADIATION 1.5 B 4-164-628-01 s SHEET RADIATION 1.5 D 4-164-629-01 s SHEET RADIATION 2 A 4-164-630-01 s SHEET RADIATION 2 B 4-672-834-11 s SCREW, +B EG GRIP 4-169-621-01 s SHEET RADIATION 1 B 4-171-215-01 s EMC FLEX SHEET 5-15 PMW-EX1R...
Page 90
Front Block P2.6 x 5 P2.6 x 5 P2.6 x 5 5-16 PMW-EX1R...
Page 91
3-694-181-03 s TYPE1,AROCK PRECISION +P2.6X5 3-968-729-52 s SCREW (M2), LOCK ACE, P2 4-164-616-02 s MAIN FRAME REAR 4-164-859-02 s CASE (R) 4-164-878-01 s FRONT FRAME 4-164-861-01 s SHEET, C MOS FLEXIBLE 7-627-556-57 s PRECISION SCREW +P 2.6X5 TYPE1 5-17 PMW-EX1R...
Page 92
1-829-414-22 s CABLE, CONNECTION (COMPONENT) 1-831-553-22 s CORD, CONNECTION (AV MULTIPLE) 3-278-903-01 s SHORUDER BELT 4-130-649-04 s CD-ROM (UTILITY SOFTWARE) 4-163-183-01 s MANUAL, INSTRUCTION (J) 4-163-183-11 s MANUAL, INSTRUCTION (CE/E/UC) 4-163-183-21 s MANUAL, INSTRUCTION (CN) 4-164-150-01 s CD-ROM (INSTRUCTION MANUAL) (CE/E/UC) 5-18 PMW-EX1R...
Need help?
Do you have a question about the PMW-EX1R and is the answer not in the manual?
Questions and answers