Metra Electronics XSVI-2003-NAV Installation Instructions

XSVI-2003-NAV INSTALLATION INSTRUCTIONS
In the GM vehicles listed on back there are no 12 volt accessory wires in the factory radio harness mak-
ing the installer run an accessory wire to the fuse box or underneath the steering column when installing
an aftermarket radio. The XSVI-2003-NAV is designed to provide a 12 volt 10 amp switched accessory
output along with the rest of the wires needed to install an aftermarket radio. The R.A.P. (Retained
Accessory Power) function is retained by the XSVI-2003-NAV.
The XSVI-2003-NAV also provides essential wires required for aftermarket radios that have navigation.
Provided is VSS (Vehicle Speed Sense), Reverse, and Parking Brake. This cuts down the installation time
since the installer does not have to look for these wires in the vehicle.
Note: The XSVI-2003-NAV does not retain the factory warning chimes that are pro-
vided by the factory radio, Onstar, or the factory amplifier if so equipped.
Wiring the XSVI-2003-NAV: Wiring up the XSVI-2003-NAV is like wiring up any other wire harness that
would attach to the aftermarket radios harness. The Metra/EIA wire code can be found on the back of
this package that will aid you in the wiring of your aftermarket radio.
Navigation wire colors:
Blue/Pink – VSS (Vehicle Speed Sense)
Green/Violet – Reverse
Lt. Green – Parking Brake
INITIALIZE THE XSVI INTERFACE BEFORE TURNING ON RADIO: With all connections made and har-
nesses connected to the vehicle, turn ignition key to the ON position for thirty seconds, then turn
key off.
(See Applications on back of page)
INSTXSVI-2003-NAV
www.metraonline.com
1-800-221-0932
XSVI-2003-NAV INSTALLATION INSTRUCTIONS
In the GM vehicles listed on back there are no 12 volt accessory wires in the factory radio harness mak-
ing the installer run an accessory wire to the fuse box or underneath the steering column when installing
an aftermarket radio. The XSVI-2003-NAV is designed to provide a 12 volt 10 amp switched accessory
output along with the rest of the wires needed to install an aftermarket radio. The R.A.P. (Retained
Accessory Power) function is retained by the XSVI-2003-NAV.
The XSVI-2003-NAV also provides essential wires required for aftermarket radios that have navigation.
Provided is VSS (Vehicle Speed Sense), Reverse, and Parking Brake. This cuts down the installation time
since the installer does not have to look for these wires in the vehicle.
Note: The XSVI-2003-NAV does not retain the factory warning chimes that are pro-
vided by the factory radio, Onstar, or the factory amplifier if so equipped.
Wiring the XSVI-2003-NAV: Wiring up the XSVI-2003-NAV is like wiring up any other wire harness that
would attach to the aftermarket radios harness. The Metra/EIA wire code can be found on the back of
this package that will aid you in the wiring of your aftermarket radio.
Navigation wire colors:
Blue/Pink – VSS (Vehicle Speed Sense)
Green/Violet – Reverse
Lt. Green – Parking Brake
INITIALIZE THE XSVI INTERFACE BEFORE TURNING ON RADIO: With all connections made and har-
nesses connected to the vehicle, turn ignition key to the ON position for thirty seconds, then turn
key off.
(See Applications on back of page)
INSTXSVI-2003-NAV
www.metraonline.com
1-800-221-0932
XSVI-2003-NAV INSTALLATION INSTRUCTIONS
In the GM vehicles listed on back there are no 12 volt accessory wires in the factory radio harness mak-
ing the installer run an accessory wire to the fuse box or underneath the steering column when installing
an aftermarket radio. The XSVI-2003-NAV is designed to provide a 12 volt 10 amp switched accessory
output along with the rest of the wires needed to install an aftermarket radio. The R.A.P. (Retained
Accessory Power) function is retained by the XSVI-2003-NAV.
The XSVI-2003-NAV also provides essential wires required for aftermarket radios that have navigation.
Provided is VSS (Vehicle Speed Sense), Reverse, and Parking Brake. This cuts down the installation time
since the installer does not have to look for these wires in the vehicle.
Note: The XSVI-2003-NAV does not retain the factory warning chimes that are pro-
vided by the factory radio, Onstar, or the factory amplifier if so equipped.
Wiring the XSVI-2003-NAV: Wiring up the XSVI-2003-NAV is like wiring up any other wire harness that
would attach to the aftermarket radios harness. The Metra/EIA wire code can be found on the back of
this package that will aid you in the wiring of your aftermarket radio.
Navigation wire colors:
Blue/Pink – VSS (Vehicle Speed Sense)
Green/Violet – Reverse
Lt. Green – Parking Brake
INITIALIZE THE XSVI INTERFACE BEFORE TURNING ON RADIO: With all connections made and har-
nesses connected to the vehicle, turn ignition key to the ON position for thirty seconds, then turn
key off.
(See Applications on back of page)
INSTXSVI-2003-NAV
www.metraonline.com
1-800-221-0932
REV. 11/05/07
METRA ELECTRONICS CORPORATION © COPYRIGHT 2007
REV. 11/05/07
METRA ELECTRONICS CORPORATION © COPYRIGHT 2007
REV. 11/05/07
METRA ELECTRONICS CORPORATION © COPYRIGHT 2007
XSVI-2003-NAV INSTALLATION INSTRUCTIONS
In the GM vehicles listed on back there are no 12 volt accessory wires in the factory radio harness mak-
ing the installer run an accessory wire to the fuse box or underneath the steering column when installing
an aftermarket radio. The XSVI-2003-NAV is designed to provide a 12 volt 10 amp switched accessory
output along with the rest of the wires needed to install an aftermarket radio. The R.A.P. (Retained
Accessory Power) function is retained by the XSVI-2003-NAV.
The XSVI-2003-NAV also provides essential wires required for aftermarket radios that have navigation.
Provided is VSS (Vehicle Speed Sense), Reverse, and Parking Brake. This cuts down the installation time
since the installer does not have to look for these wires in the vehicle.
Note: The XSVI-2003-NAV does not retain the factory warning chimes that are pro-
vided by the factory radio, Onstar, or the factory amplifier if so equipped.
Wiring the XSVI-2003-NAV: Wiring up the XSVI-2003-NAV is like wiring up any other wire harness that
would attach to the aftermarket radios harness. The Metra/EIA wire code can be found on the back of
this package that will aid you in the wiring of your aftermarket radio.
Navigation wire colors:
Blue/Pink – VSS (Vehicle Speed Sense)
Green/Violet – Reverse
Lt. Green – Parking Brake
INITIALIZE THE XSVI INTERFACE BEFORE TURNING ON RADIO: With all connections made and har-
nesses connected to the vehicle, turn ignition key to the ON position for thirty seconds, then turn
key off.
(See Applications on back of page)
INSTXSVI-2003-NAV
www.metraonline.com
1-800-221-0932
XSVI-2003-NAV INSTALLATION INSTRUCTIONS
In the GM vehicles listed on back there are no 12 volt accessory wires in the factory radio harness mak-
ing the installer run an accessory wire to the fuse box or underneath the steering column when installing
an aftermarket radio. The XSVI-2003-NAV is designed to provide a 12 volt 10 amp switched accessory
output along with the rest of the wires needed to install an aftermarket radio. The R.A.P. (Retained
Accessory Power) function is retained by the XSVI-2003-NAV.
The XSVI-2003-NAV also provides essential wires required for aftermarket radios that have navigation.
Provided is VSS (Vehicle Speed Sense), Reverse, and Parking Brake. This cuts down the installation time
since the installer does not have to look for these wires in the vehicle.
Note: The XSVI-2003-NAV does not retain the factory warning chimes that are pro-
vided by the factory radio, Onstar, or the factory amplifier if so equipped.
Wiring the XSVI-2003-NAV: Wiring up the XSVI-2003-NAV is like wiring up any other wire harness that
would attach to the aftermarket radios harness. The Metra/EIA wire code can be found on the back of
this package that will aid you in the wiring of your aftermarket radio.
Navigation wire colors:
Blue/Pink – VSS (Vehicle Speed Sense)
Green/Violet – Reverse
Lt. Green – Parking Brake
INITIALIZE THE XSVI INTERFACE BEFORE TURNING ON RADIO: With all connections made and har-
nesses connected to the vehicle, turn ignition key to the ON position for thirty seconds, then turn
key off.
(See Applications on back of page)
INSTXSVI-2003-NAV
www.metraonline.com
1-800-221-0932
XSVI-2003-NAV INSTALLATION INSTRUCTIONS
In the GM vehicles listed on back there are no 12 volt accessory wires in the factory radio harness mak-
ing the installer run an accessory wire to the fuse box or underneath the steering column when installing
an aftermarket radio. The XSVI-2003-NAV is designed to provide a 12 volt 10 amp switched accessory
output along with the rest of the wires needed to install an aftermarket radio. The R.A.P. (Retained
Accessory Power) function is retained by the XSVI-2003-NAV.
The XSVI-2003-NAV also provides essential wires required for aftermarket radios that have navigation.
Provided is VSS (Vehicle Speed Sense), Reverse, and Parking Brake. This cuts down the installation time
since the installer does not have to look for these wires in the vehicle.
Note: The XSVI-2003-NAV does not retain the factory warning chimes that are pro-
vided by the factory radio, Onstar, or the factory amplifier if so equipped.
Wiring the XSVI-2003-NAV: Wiring up the XSVI-2003-NAV is like wiring up any other wire harness that
would attach to the aftermarket radios harness. The Metra/EIA wire code can be found on the back of
this package that will aid you in the wiring of your aftermarket radio.
Navigation wire colors:
Blue/Pink – VSS (Vehicle Speed Sense)
Green/Violet – Reverse
Lt. Green – Parking Brake
INITIALIZE THE XSVI INTERFACE BEFORE TURNING ON RADIO: With all connections made and har-
nesses connected to the vehicle, turn ignition key to the ON position for thirty seconds, then turn
key off.
(See Applications on back of page)
INSTXSVI-2003-NAV
www.metraonline.com
1-800-221-0932
REV. 11/05/07
METRA ELECTRONICS CORPORATION © COPYRIGHT 2007
REV. 11/05/07
METRA ELECTRONICS CORPORATION © COPYRIGHT 2007
REV. 11/05/07
METRA ELECTRONICS CORPORATION © COPYRIGHT 2007