Kenmore 911.99002 Technical Data Sheet

NOTE:
• BAKE/TIME BAKE — Bake and broil units cycle during
preheat and balance of operation, one unit is on at a time.
• CLEAN — Broil unit only on
during 1st 30 minutes or
until oven reaches 750°F.
During balance of clean
oven will cycle between
bake and broil units.
Convection fan running make the following checks:
• Check the voltage from terminal CF to N on control - should read
120V in convection bake or roast mode.
• If voltage is OK, check convection fan motor. It reads approximately 15-20Ω's at room
temperature. Check to make sure fan shaft is not rubbing on oven liner.

ERC FAILURE CODES

CODE CORRECTION
MEANING
If code cannot be cancelled, unplug keypad and
F0 Clear/Off pad is shorted or touch board fault
power up. If 0) ceases, replace keypad/ glass
(after approx. 100 secs).
asm., If 0) is still present, replace main control.
Loss of element redundant driver protection.
F1 If code cannot be cancelled, replace control.
Any key (other than Start of Clear/OFF pad)
If code cannot be cancelled, unplug keypad and
F7
shorted (after approx. 40 secs).
power up. If code ceases, replace keypad/glass
F6
asm. If code is still present, replace main control.
F2 • Look for welded relay contacts. (Heating elements on
Over-temperature-915°F if lock circuit is
in off mode.)
made, 615°F otherwise.
• Look for high resistance in the sensor circuit due to high contact resistance (poor terminal crimp, deformed
terminals, loose connection inside sensor tube) or intermittent solder joint.
• Electrical noise interference in the sensor circuit ( Ham radio, cordless phone, etc.)
Sensor circuits open (2900 Ohms or greater).
• Disconnect power to range.
F3
• Disconnect sensor connector at control. Measure
F4 Sensor circuits shorted (950 Ohms or less).
sensor resistance at control connector (take care not
to damage terminals in block)-Should read 1100Ω at room ambient (approx.72°F).
• Measure each sensor lead from connector block to ground. If shorted, look for pinched or cut wire in sensor
circuit.
• Check connector terminals- Look for deformed or corrosion on terminals. Repair or replace.
• Check connector at sensor (remove sensor and carefully pull leads with connector into oven).
• If all above is ok, replace control.
Both lock and unlock circuits are activated at Check wiring and test operation of switches.
F9
FC the same time (after approx. 60 secs.) Perform resistance check.
Loss of door motor redundant driver protection.
FF Replace control
FA Surface warmer on indicator light supervisor Replace control
error
FE
NOTE: Connections can be intermittent due to a corrosive buildup between the connection to the terminals, or
by being bent by the insertion of a probe, etc.
STORAGE DRAWER REMOVAL
To Remove:
1. Pull the drawer out until it stops.
2. Lift the front of the drawer until the stops clear the guides.
3. Remove the drawer.
To Replace:
1. Place the drawer rail on the guides.
2. Push the drawer in until it stops.
3. Lift the front of the drawer and push in until the stops clear the guides.
4. Lower the front of the drawer and push in until it closes.
——— If Drawer Won't Close ———
——— If Drawer is Crooked ———

MOTORIZED DOOR LOCK

The motorized door lock assembly is located above the oven. The
assembly consists of a lock motor cam and switch assembly, lock
hook, heat barrier, and mounting plate.
229C4059P244
• T E C H N I C A L D A T A S H E E T •
Motorized Door Lock Operation:
The lock motor is energized when the control is set for Clean
and Clean Time selected. The K1 relay contact will close and
complete the circuit that supplies the voltage to the lock motor.

REPLACING THE COOKTOP LIGHT BULB

CAUTION: Disconnect electrical power to the range at the main circuit
breaker or fuse box before attempting to replace the cooktop light bulb. Do
not touch a hot light bulb with wet hands or a wet cloth. Wait until the bulb
has cooled and use a dry cloth.
To Remove Old Bulb:
1. Pull the range away from the wall.
2. Remove the two screws from the top on the
back of the range.
3. Pull up on the hand grips on the back of the range
until the tabs at the bottom of the cooktop light
housing separate from the back of the range.
4. Pull out the cooktop light housing as far as possible, about 2 inches.
5. Remove the light bulb by unplugging it from both sockets with one motion.
To Install New Bulb:
1. Install the new light bulb by plugging it into
both sockets with one motion.
2. Using the hand grips on the cooktop light
housing, lift up and push the housing back into
the rear wall of the range. Then lower the
housing until the bottom tabs are inserted back
into the range.
3. Reattach the screws along the top edge on the back of the range.
Then push the range back against the wall.
NOTE: Display of Control will flash "LOCK DOOR" if the door switch is in the "C" to "NC" position.
(Door open)
• The word "LOCKED DOOR" will flash on and off in the display while the
lock motor is in motion. When the door is locked the word "LOCKED
DOOR" remains illuminated in the display.
• CAM - The cam on the motor performs two functions:
1. Positions the lock hook in the door to prevent opening during clean
operation.
2. Operates the lock switches which tell the control if the door is unlocked or
locked and ready for clean operation.
NOTE: When door is either being locked or unlocked both lock switches will
be in the open position.
Kenmore ELITE Radiant Free-Standing
Part Description Repair Part Number Part Description
6" Haliant Element WB30K5033 Glass Panel Asm-White
Bridge Element WB30T10088 Glass Panel Asm-Bisque
9"Haliant Element WB30T10035 Glass Panel Asm-GPH/ SS
6"Haliant Element (Warmer) WB30T10042 Glass MT ASM-Black
Infinite Switch (Warmer) WB24T10012 Glass MT ASM-Bisque
Infinite Switch (Dual) WB24T10015 Glass MT ASM-White
Infinite Switch-2600W WB24T10032 Glass MT ASM-GPH
Infinite Switch-1500W WB24T10028 Bake Element -Hidden
Oven Control WB27T10137 Convection Element
Oven Control-Stainless WB27T10144 Broil Element
Sensor WB23T10002 Halogen Lamp
Glass Panel Asm-Black WB27T10160
Repair Part Number
WB27T10155
WB27T10159
WB27T10157
WB62T10040
WB62T10039
WB62T10038
WB62T10037
WB44T10015
WB44T10001
WB44T10008
WB08T10007