Table of Contents
Advertisement
Operating Instructions
33575
33576
33577
1.
Notes......................................................................................................................02
2.
Functions...............................................................................................................04
2.1.
Binding.........................................................................................................04
2.1.1
Binding multiple receivers...................................................................................04
2.2.
Fail-Safe function...............................................................................................04
2.3
Range-checking...........................................................................................05
3.
Receiver..................................................................................................................06
3.1.
Connections..................................................................................................07
3.2.
Receiver set-up menu........................................................................................08
3.3.
Free mixers.......................................................................................................08
3.4
Assigning the gyro axes......................................................................................10
4.
Programming the gyro settings...............................................................................12
4.1.
Programming PID correction..............................................................................12
4.2.
Programming the factors....................................................................................13
4.2.1
Programming, transmitter with proportional controls............................................13
4.2.2
Programming, transmitter without proportional controls.......................................14
4.3
5.
Firmware update..............................................................................................16
6.
GRAUPNER/SJ GmbH - Postfach 1242 - 73230 Kirchheim/Teck - www.graupner.de
Receiver GR-12 SH +3xG HoTT
Receiver GR-12 +3xG HoTT
Receiver GR-12 +3xG+3A Vario
.................................................................................
Manual V1.0
Revision: Januar 2013
....................14
Advertisement
Table of Contents
Related Manuals for GRAUPNER 33575
Summary of Contents for GRAUPNER 33575
-
Page 1: Table Of Contents
Programming, transmitter with proportional controls..........13 4.2.2 Programming, transmitter without proportional controls........14 Initialising the gyro ....14 ................. Firmware update....................16 Conformity declaration / Guarantee / Manufacturer’s declaration / Disposal..17 Manual V1.0 Revision: Januar 2013 GRAUPNER/SJ GmbH – Postfach 1242 – 73230 Kirchheim/Teck – www.graupner.de... -
Page 2: Notes
Not suitable for children under fourteen years. This receiver is not a toy! The receiver is also equipped with a telemetry function which is only available in combination with a Graupner/SJ HoTT 2.4 system. If you do not own a Graupner/SJ HoTT 2.4 system, the receiver will not work. - Page 3 Note! Ensure that all your HoTT components are loaded with the current version of the software at all times. Note! Safety is no accident, and radio-controlled models are not playthings! Manual Receiver GR-12+ 3xG Graupner HoTT 2. 4...
-
Page 4: Functions
2. FUNCTIONS 2.1. Binding The Graupner/SJ HoTT 2.4 receiver must be “bound” to “its” Graupner/SJ HoTT 2.4 RF module (transmitter) before a radio link can be created between them; this process is known as “binding”. Binding is only necessary once for each combination of receiver / RF module, so the binding procedure described below only needs to be repeated if you add more receivers. -
Page 5: Range-Checking
The gyro system remains active in a fail-safe situation. 2.3 Range-checking The range of your Graupner/SJ HoTT 2.4 system can be checked as described in the following instructions. We recommend that you ask a friend to help you with the procedure. -
Page 6: Receiver
(-) is brown, the positive (+) red and the signal orange. The servo sockets of Graupner/SJ HoTT 2.4 receivers are numbered sequentially. The socket for channel 6 can also be programmed to deliver a (digital) sum signal (see section 3.2: Receiver set-up). - Page 7 (frame rate) of 10 ms at this point. If your system includes some or all analogue servos, you should always select 20 ms, as many analogue servos cannot process the higher frame rate, and may respond Manual Receiver GR-12+ 3xG Graupner HoTT 2. 4...
-
Page 8: Receiver Set-Up Menu
TO CHANNEL: part of the source channel signal (FROM CHANNEL) is mixed into the target channel (TO CHANNEL). The mixer ratio is determined by the percentage values entered in the “TRAVEL-“ and “TRAVEL+” lines. Select “0” if you do not require the mixer. Manual Receiver GR-12+ 3xG Graupner HoTT 2. 4... - Page 9 Two elevator servos (channel 6 for the second elevator servo) RX FREE MIXER < > >MISCHER: MASTER CH: SLAVE CH: >TRIM: >TRAVEL-: +100% TRAVEL+: +100% Manual Receiver GR-12 + 3xG Graupner HoTT 2. 4...
-
Page 10: Assigning The Gyro Axes
The only option is to re-install it in the model by turning it round physically. However, if your model is fitted with programmable servos (e.g. Graupner DES, HVS or HBS types - see the instructions for the update program ‘Firmware_Upgrade_grStudio - then it is possible to reverse the direction of rotation at the servo itself. - Page 11 ELEVATOR Model movement Control surface response (seen from the tail) RUDDER Model movement Control surface response (seen from the tail) AILERON Model movement Control surface response (seen from the tail) Manual Receiver GR-12+ 3xG Graupner HoTT 2. 4...
-
Page 12: Programming The Gyro Settings
D factor. However, if you select a lower setting for the P factor, then you may be able to set a higher D factor value before the onset of control surface oscillation. The gyro effect can be optimised by fine- tuning the D factor. Manual Receiver GR-12+ 3xG Graupner HoTT 2. 4... -
Page 13: Programming The Factors
• It may be sensible or easier to activate the gyro for one axis only at first, and then to establish the optimum setting for that axis, rather than for several axes simultaneously. Manual Receiver GR-12+ 3xG Graupner HoTT 2.4... -
Page 14: Programming, Transmitter Without Proportional Controls
Gyro suppression reduces the stabilising action progressively as the transmitter controls are defl ected away from centre; at +/- 100% the gyro is completely disabled. Your model is now ready to fl y .. ! Manual Receiver GR-12+ 3xG Graupner HoTT 2. 4... - Page 15 XP, Vista or 7. You will also need the separately available USB interface, Order No. 7168.6 and the adapter lead, Order No. 7168.6A or 7168.S (33575: additional adapter lead, Order No. 33565.1). The programs and fi les required for this can be found in the Download area for the corresponding products at www.graupner.de.
-
Page 16: Firmware Update
Order No. 23046 for GR-12SC+ receiver, or Order No. 33565.1 for GR-12SH+ receiver Three-core connecting lead, Order No. 33700.1 Please refer to the detailed update instructions in the Download area for the corresponding item at http://www.graupner.de. Manual Receiver GR-12+ 3xG Graupner HoTT 2. 4... -
Page 17: Conformity Declaration / Guarantee / Manufacturer's Declaration / Disposal
Measures for the efficient use of the radio frequency spectrum § 3 (2) (Article 3 (2)) Kirchheim, 17. April 2013 Ralf Helbing, Geschäftsführer Ralf Helbing, Managing Director Graupner/ SJ GmbH Henriettenstraße 96 D-73230 Kirchheim/Teck Germany Tel: 07021/722-0 Fax: 07021/722-188 EMail: info@graupner.de Manual Receiver GR-12+ 3xG Graupner HoTT 2. 4... - Page 18 If material defects or manufacturing faults should arise in a product distributed by us in the Federal Republic of Germany and purchased by a consumer (§ 13 BGB), we, Graupner/SJ GmbH, D-73230 Kirchheim/Teck, Germany, acknowledge the obligation to correct those defects within the limitations described below.
- Page 19 Date de remise Name des Käufers Owner´s name Nom de I`acheteur Firmenstempel und Unterschrift des Einzelhändlers Straße, Wohnort Stamp and signature of dealer Complete adress Adresse complète Cachet et signature du vendeur Manual Receiver GR-12+ 3xG Graupner HoTT 2. 4...
- Page 20 Sous réserve de modifications et de possibilité de livraison. Livraison uniquement au travers de maga- sins spécialisés en modélisme. Nous pourrons vous communiquer l’adresse de votre revendeur le plus proche. Nous ne sommes pas responsables d’éventuelles erreurs d’impression. Mai 2013 - DE V1.0 Manual Receiver GR-12+ 3xG Graupner HoTT 2. 4...