GE Monogram ZV48T Installation Instructions Manual
30", 36" and 48" professional vent hoods
Hide thumbs
Also See for Monogram ZV48T:
- Installation instructions manual (17 pages) ,
- Installation instructions manual (16 pages)
Related Manuals for GE Monogram ZV48T
Summary of Contents for GE Monogram ZV48T
-
Page 1: Installation Instructions
Installation Instructions If you have questions, call 800.GE.CARES or visit our website at: www.monogram.com 30", 36" and 48" Professional Vent Hoods Models: ZV48T, ZV48S ZV36T, ZV36S ZV30T, ZV30S Monogram. ®... -
Page 2: Before You Begin
Installation Instructions BEFORE YOU BEGIN WARNING: TO REDUCE THE RISK OF FIRE, ELECTRICAL Read these instructions completely and carefully. SHOCK OR INJURY TO PERSONS, OBSERVE THE • IMPORTANT - Save these instructions for FOLLOWING: local inspector’s use. A. Use this unit only in the manner intended by the •... -
Page 3: Table Of Contents
PRODUCT DIMENSIONS 47-15/16" 12" 40" 12" 18" 18" 25" 25" 47-15/16" 47-15/16" Model ZV48S With Straight Sides Model ZV48T With Tapered Sides 28" 35-15/16" 12" 12" 18" 18" 25" 35-15/16" 35-15/16" 25" Model ZV36S With Straight Sides Model ZV36T With Tapered Sides 22"... -
Page 4: Installation Clearances
SOFFIT 12" Duct Cover 30" MIN. 6" Duct Covers 36" MAX. Hood Model 6” Duct Cover Dimensions ZV48T, ZV48S ZX48DC6 6"H x 19-11/16"W x 11-7/8"D ZV36T, ZV36S ZX36DC6 6"H x 15-3/4"W x 11-7/8"D ZV30T, ZV30S ZX36DC6 6"H x 15-3/4"W x 11-7/8"D... -
Page 5: Installation Height, Duct Cover Accessories
Advance Planning DETERMINE INSTALLATION HEIGHT, DUCT COVER ACCESSORIES These vent hoods must be installed 30" min. to Tapered or Straight-Sided Straight-Sided Hoods Hoods Only 36" max. above the standard 36" high cooking w/ Standard w/ Full-Width surface. The exact hood installation height is Duct Cover Duct Cover determined by the ceiling height. -
Page 6: Advance Planning
Advance Planning ADVANCE PLANNING POWER SUPPLY IMPORTANT - (Please read carefully) Ductwork Planning • These vent hoods are equipped for 10" round WARNING: ductwork. For best performance, use 10" round FOR PERSONAL SAFETY, THIS APPLIANCE MUST ductwork on the 48" wide hoods. 30" and 36" hoods BE PROPERLY GROUNDED. -
Page 7: Duct Fittings
10" Dia. 56 ft. *Actual length of straight duct plus duct fitting equivalent. Equivalent length of duct pieces are based on actual tests conducted by GE Evaluation Engineering and reflect requirements for good venting performance with any ventilation hood. Total Duct Run... -
Page 8: Installation Preparation
Installation Preparation TOOLS AND MATERIALS REQUIRED (NOT SUPPLIED) Hammer Duct tape Electric or battery operated drill Key Hole Saw Wire cutter/stripper and 1/8", 3/8" bits Pencil and tape measure 10" round metal duct, length to suit installation. Safety glasses Wire nuts Phillips and flat Spirit level blade... -
Page 9: Parts Provided
Installation Preparation PARTS PROVIDED Locate the parts packed with the hood. Wood Support Duct Transition with Original Screws with Damper 2 Stainless Steel Grease Filters (3 filters with 48" models) Heat Lamp (2 with 48" models) 2 Grease Filter Trays Allen Wrench 2 Implement Rods and 4 Stand-offs (3 supports with 48"... -
Page 10: Step 1, Determine Ductwork And Wiring Locations
Installation Instructions STEP 1 DETERMINE HOOD, DUCTWORK AND WIRING LOCATIONS • Use a level to draw the cooktop centerline location. Draw the line to ceiling height. 9-7/8" • Measure desired distance from the bottom of the hood to the cooking surface, 30" min. to 36" max. Top of Hood Note: If you are installing the hood with duct covers, be sure to read “Using Duct Cover Accessories”... -
Page 11: Step 2A Install Hood Onto Wall
Installation Instructions STEP 2A INSTALL HOOD ONTO WALL IMPORTANT: Framing must be capable of supporting up to 150 lbs. Install Transition Onto Top of Hood SKIP THIS STEP IF INSTALLING BENEATH A SOFFIT OR CABINET, GO TO STEP 2B. • Locate at least 2 vertical studs at the wood support. Duct •... -
Page 12: Step 2B, Install Hood Beneath Soffit
Engage Top “A” “B” Add Shims 1/4" Gap Keyhole Slots If Bottom Centerline to Stud Hood Width Is Recessed and Keyhole Slots At the Top ZV48T 19-9/16" 40" Push Back Back to Wall Wall ZV48S 23-9/16" 47-15/16" ZV36T 13-9/16" 28"... -
Page 13: Step 3 Connect Ductwork
Installation Instructions STEP 4 CONNECT ELECTRICAL STEP 3 CONNECT DUCTWORK • Install ductwork, making connections in direction of Verify that power is turned off at the source. airflow as illustrated. • Secure joints in ductwork with sheetmetal screws. WARNING: • Wrap all duct joints with duct tape for an airtight seal. If house wiring is not •... -
Page 14: Step 6 Install Motor
Installation Instructions STEP 6 INSTALL MOTOR STEP 7 INSTALL FILTERS Outlet Attachment Spring Slot Clip • From the inside of the hood, slip motor into the • Place filter drip trays into the rear of the hood. attachment slot on the left. •... -
Page 15: Step 8 Install Implement Rods
Installation Instructions STEP 8 INSTALL IMPLEMENT RODS Screw Stand-offs Into Hood Use Allen Wrench to Secure Rod to Stand-offs • Use a flat blade screwdriver to install stand-offs into the bottom of the hood. • Align implement rod to stand-offs with the screw hole towards the inside of the hood. - Page 16 1.800.444.1845. Note: Product improvement is a continuing endeavor at General Electric. Therefore, materials, appearance and specifications are subject to change without notice. GE Consumer & Industrial Pub. No. 49-80151-4 GE Appliances Dwg. No. 164D4290P108 General Electric Company...