Fault Finding - Electrolux GSG 580 User's Installation And Servicing Manual

4. Check the Gas Control Taps for ease of operation.
5. Check and clean the Main Burner Injectors, and remove
all foreign matter around the openings into the Main
Burners.
6. Light, and check the Pilot Burner, the operation of the
Thermocouple, and the lighting of the Main Burners.
7. Check the Main Burner Plaques to ensure that there is
even burning and no light-back, and no cracks in the
ceramic plaques.
REPLACEMENT OF PARTS & SERVICING
The servicing of this appliance must be carrier out a
competent person who has CITB Certification, and who is
CORGI Registered. All work must comply with the Gas
Safety Regulations.
BEFORE DISMANTLING ANY GAS-CARRYNG
PARTS, TURN OFF THE GAS SUPPLY AT THE
ISOLATING TAP.
It is recommended that the servicing of this appliance should
be carried out under a service contract provided by Electrolux
SYMPTON
Smell of gas
Pilot Burner does not light using
Piezo Ignitor
Pilot Burner does not light using
ignition OR taper
Pilot Burner goes out following ignitor
Main Burner flames uneven
lifting off, burning erratically
Pilot estabilishes and Main Burner ignites but
Pilot and Main Burner go out after several
minutes
A. OUTER TOP PANEL
REMOVE/REPLACE (figure 3)
Pull the outer top panel forward (1) and lift clear to
1.
release keyhole slots from the locating pegs on the side
panels then lift clear of the appliance.
Commercial Service (ECS). Benefits of a service contract
include regular visits from trained engineers, priority
breakdown treatment and extensive spare parts back up
service. A service contract is available to cover ALL your
equipment and work carried out is guaranteed. For details
contact Electrolux Commercial Service: 0345-364364.
SPARE PARTS
Only genuine Electrolux spares should be used on this
appliance and can be obtained from:
When ordering spare parts please quote the serial number and
the model number of the appliance together with the part
number of the component required.

FAULT FINDING

POSSIBLE CAUSE
a) Gas leak
a) No gas to appliance
b) No spark at Ignition Electrode
c) Ignition Cable damaged
d) Faulty Ignition Electrode (cracked ceramic)
e) Ignition Unit (loose fitting, no earth)
f) Faulty Igniter
a) Blocked Pilot Injector
a) Thermocouple tip out of position
b) Thermocouple loose at Gas Control Tap
c) Thermocouple damage (tip burned)
d) Faulty Gas Control Tap
a) Dirt blocking Burner Inlet
b) Blocked Injector
c) Wrong gas pressure
d) Wrong Injector fitted for gas type
e) Ceramic Plaque on Main Burner
cracked or broken
f) Thermocouple Tip not securely held in Pilot
Burner
2.
B. INNER LINER
REMOVE/REPLACE (figure 3)
1.
2.
6
Electrolux Foodservice Equipment
Crystal Court Aston Cross,
Business Park Aston Birminghan
B6 5RQ U.K.
telephone: 0121 – 220 2852/3
telefax: 0121 - 2202850
REMEDY
a) Locate leak and make joint sound
a) Turn on gas at Isolating Tap
b) Remake lead connections
c) Replace Ignition Cable
d) Replace Electrode
e) Tighten locknut on Igniter
f) Replace Igniter
a) Clean or replace Pilot Injector
a) Check Pilot Burner for damage replace if
necessary
b) Clean end of Thermocouple at Tap tighen
Thermocouple Nut - finger tight, then a
further ½ turn with a spanner.
c) Replace the Thermocouple
d) Replace Tap
a) Clean
b) Clean or fit new Injector
c) Check and adjust pressure
d) Check gas type and fit correct Injectors
e) Replace Main Burner
a) Reposition and tighten the Thermocouple
in Pilot Burner
Replace in a reverse sequence ensuring that there is no
gap between the top of side panels and the outer top
panel..
Complete procedure A.
Lift the inner liner (2) clear of the appliance.