THE UNIT IS INTENDED FOR HOUSEHOLD
USAGE ONLY
BEFORE USING THE UNIT
Note:
–
In case of unit transportation or storage at
low temperature it is necessary to keep it
for at least two hours at room temperature
before switching on.
B e f o r e u s i n g t h e u n i t , w a s h t h e c h o p p i n g
–
k n i f e ( 8 ) , t h e c h o p p e r b o w l ( 9 ) , t h e w h i s k
(11) and the measuring cup (12) with warm
water and a neutral detergent, then rinse and
dry them.
Do not immerse blender attachment (1) and
–
mash making attachment (14) into water
entirely, wash them under water jet, provided
that no water gets inside the attachment.
–
Wipe the motor unit (2), geared lid (7), whisk
gear (10) and mash making attachment gear
(13) with a soft slightly damp cloth.
Attention!
-
Do not immerse the motor unit (2), geared
lid (7), whisk gear (10), mash making
attachment gear (13), power cord and
power plug into water or any other liquids.
-
Do not put the attachments and bowl in a
dish washing machine.
Selection of attachment rotation speed
–
Change the attachment rotation speed using
the speed control (5). Press and hold "I" but-
ton (4), select the the required rotation speed
by turning the speed control (5).
For operation at the maximal rotation speed,
–
press and hold the (3) "II" button.
Continuous operation time
Continuous operation time of attachments (1,
11, 14) should not exceed 1 minute. Continuous
operation time of mini-chopper (9) should not
exceed 20-30 seconds. Make at least a two-
minute interval between operation cycles.
USING THE BLENDER ATTACHMENT (pic. 1).
WARNING:
Before assembling make sure that the power
–
plug is not inserted into the socket.
To install the blender attachment (1) press
–
the attachment lock buttons (6) simultane-
ously and insert the blender attachment (1)
into the motor unit (2) then release the lock
VT-1469.indd 5
buttons (6) and make sure that the attach-
ment is firmly locked.
Insert the plug into the socket.
–
Immerse the blender attachment (1) into the
–
bowl with products, that you want to chop/
mix; you can use the measuring cup (12)
for it.
–
Select the required attachment rotation
speed by pressing and holding button «I» (4)
or «II» (3).
Note:
Food products should be put into the bowl
–
before switching the unit on.
Before starting to chop/mix, we recommend
–
to peel fruit, remove inedible parts, such as
kernels, and cut fruit into 2х2 cm cubes.
After you finish using the unit, take the plug
–
out of the socket and remove the attach-
ment (1) by pressing the buttons (6) simul-
taneously.
Attention!
Do not remove the blender attachment (1)
–
during blender operation.
To avoid damage of blades, do not process
–
too hard products such as cereals, rice, spic-
es, coffee beans, ice, cheese, frozen food.
If the products are difficult to process add
–
some water.
USING THE WHISK (pic. 2).
Use the whisk attachment (11) only to make
cream, biscuit dough or mixing ready desserts.
WARNING:
Before assembling make sure that the power
–
plug is not inserted into the socket.
Insert the whisk (11) into the gear (10).
–
Press the attachment lock buttons (6) simul-
–
taneously and insert the whisk gear (10) into
the motor unit (2), release the lock buttons
(6), make sure that the gear is firmly locked.
Insert the plug into the socket.
–
Put the whisk (11) into the bowl with products.
–
–
Select the required whisk rotation speed by
pressing and holding button «I» (4) or «II» (3).
–
After you finish using the unit, take the plug
out of the socket, disconnect the whisk (11)
from the gear (10) and remove the gear (10)
from the motor unit (2) by pressing buttons
(6) simultaneously.
Attention!
Do not use the whisk (11) to make tight
–
dough.
5
ENGLISH
15.08.2012 12:50:42