Advertisement
10
SB660
SB660-MP
SB660-MP
WARNING
Failure to follow the installation instructions shipped with your SMART product could result in personal injury and damage to the product.
Refer to the safety warnings and precautions published by the projector manufacturer. Do not stare (or allow children to stare) directly into the projector's beam
of light.
Do not climb (or allow children to climb) on your SMART Board interactive whiteboard. Climbing on the product could result in personal injury and product
damage.
Do not stand (or allow children to stand) on a chair to touch the surface of your SMART product. Rather, wall-mount the product at the appropriate height.
To reduce the risk of fi re or electric shock, do not expose your SMART product to rain or moisture.
Two people are required to mount your SMART product because it may be too heavy for one person to safely maneuver.
Ensure that any cables extending across the fl oor to your SMART product are properly bundled and marked to prevent a tripping hazard.
CAUTION
Do not mount the SMART Board 660 or 680 interactive whiteboard on an FS570 fl oor stand. Using this older stand could result in personal injury and product
damage. Use the FS670 fl oor stand for these products instead.
Move a fl oor stand-mounted SMART Board interactive whiteboard with care. Quick stops, excessive force and uneven surfaces may cause the product to
overturn. Before moving a fl oor stand, make sure the anti-tip feet are retracted or locked in the up position.
You must connect the USB cable that came with your SMART Board interactive whiteboard to a computer that has a USB compliant port and that bears the
IMPORTANT
USB logo. In addition, the USB source computer must be compliant with CSA/UL/EN 60950 and bear the CE mark and CSA and/or UL Mark(s) for
CSA/UL 60950. This is for operating safety and to prevent damage to the SMART Board interactive whiteboard.
If your product requires replacement parts, make sure the service technician uses replacement parts specifi ed by SMART Technologies or parts with the same
characteristics as the original.
For cautions and warnings, see the SMART Board 600 and SBD600 Series Interactive Whiteboard Installation and User's Guide (smarttech.com/kb/001414).
Hardware environmental compliance
SMART Technologies supports global efforts to ensure that electronic equipment is manufactured, sold and disposed of in a safe and environmentally friendly manner.
Waste Electrical and Electronic Equipment Regulations (WEEE directive)
Waste Electrical and Electronic Equipment regulations apply to all electrical and electronic equipment sold within the European Union. When you dispose of any electrical
or electronic equipment, including SMART Technologies products, we strongly encourage you to properly recycle the electronic product when it has reached the end of its
life. If you require further information, please contact your reseller or SMART Technologies for information on which recycling agency to contact.
Restriction of Certain Hazardous Substances (RoHS directive)
This product meets the requirements of the European Union's Restriction of Certain Hazardous Substances (RoHS) Directive 2002/95/EC. Consequently, this product also
complies with other regulations that have arisen in various geographical areas, and that reference the European Union's RoHS directive.
Packaging
Many countries have regulations restricting the use of certain heavy metals in product packaging. The packaging used by SMART Technologies to ship products complies with
packaging laws.
China's Electronic Information Products Regulations
China regulates products that are classifi ed as Electronic Information Products (EIP). SMART Technologies products fall under this classifi cation and meet the requirements for
China's EIP regulations.
U.S. Consumer Product Safety Improvement Act
The United States has enacted the Consumer Product Safety Improvement Act which limits the lead (Pb) content in products used by children. SMART Technologies is committed
to complying with this initiative.
FCC Notice
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference in a residential installation.
This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television
reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
– Reorient or relocate the receiving antenna.
– Increase the separation between the equipment and receiver.
– Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
– Consult the dealer or an experienced radio/TV technician for help.
www.smarttech.com/support www.smarttech.com/contactsupport
© 2009–2011 SMART Technologies ULC. All rights reserved. SMART Board, SMART GoWire, smarttech and the SMART logo are trademarks
or registered trademarks of SMART Technologies ULC in the U.S. and/or other countries. All third-party product and company names may be
trademarks of their respective owners. Patent No. US5448263; US6141000; US6320597; US6326954; US6337681; US6741267; US6747636;
US7151533; US7289113; US7499033; US7626577; US775700; US7687736; CA2058219 and CA2252302. Other patents pending. Contents
are subject to change without notice. 03/2011.
11
*99-00622-22-B0*
12
99-00622-22-B0
Advertisement
