STRIKEMASTER Solo Owner's Manual
  1. Manuals
  2. Brands
  3. STRIKEMASTER Manuals
  4. Fishing Equipment
  5. Solo
  6. Owner's manual

STRIKEMASTER Solo Owner's Manual

Ice augers strikemaster
Hide thumbs

Advertisement

Table of Contents

It is recommended that everyone
who uses this product should read
the StrikeMaster owner's manual.
Solo® Germany The registered Solo® trademark is licensed for use in the U.S. to the German company Solo Kleinmotoren Gmbh by the U.S. affiliate, Solo incorporated.
SOLO
Owner's Manual
ATTENTION: PRIOR TO FIRST USE
!
This engine is equipped with a
decompression valve for
easier starting. Press the button
in before every start to reduce
cylinder pressure.
PRIOR
!
For best performance idle
engine for 1-2 minutes before
you start drilling.
SM14

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the Solo and is the answer not in the manual?

Questions and answers

Related Manuals for STRIKEMASTER Solo

Summary of Contents for STRIKEMASTER Solo

  • Page 1 Press the button you start drilling. in before every start to reduce cylinder pressure. SM14 Solo® Germany The registered Solo® trademark is licensed for use in the U.S. to the German company Solo Kleinmotoren Gmbh by the U.S. affiliate, Solo incorporated.

  • Page 2: Table Of Contents

    1946. There is no doubt that this year’s model is the finest ever produced by StrikeMaster Corporation. Your new StrikeMaster ice auger has all of the most wanted features in a power ice auger, to assure many years of enjoyable ice fishing. Some of these features such as workmanship, engineering excellence, and dependability have long been standards at StrikeMaster.

  • Page 4: Important Safeguards/Component & Control Locations

    IMPORTANT SAFEGUARDS It is recommended that everyone who uses this product should read this StrikeMaster Owner’s Manual before operating.  1. DO NOT use this product for any purpose other than cutting ice fishing holes. Ice augers are precision cutting tools built for the ice fisherman, and must be properly maintained and handled with caution during both cutting and transporting.

  • Page 5: Assembly Instructions

    ASSEMBLY Carefully remove blade It is recommended to guard and make sure grease inside metal collar and blade bolts are tight. Lazer transmission output shaft on the Output Shaft Blade powerhead. Standard automotive (Use 8mm closed end wheel bearing grease is suggested. wrench for Lazer blades) Insert drive shaft into auger and (Use two 10mm closed...

  • Page 6: Fueling: Oil/Fuel Instructions

    • Store fuel and oil in an approved and correctly labeled container. 1. The Solo engine has a non-vented gas cap. Air is supplied to the tank using an external venting system. (Fig 1) 2.

  • Page 7: Engine Start Preparations

    Be sure the on/off switch is NOT in the off position and start once Fig 4 again. If the engine still fails to start, contact your local Solo authorized repair center located on our website. STARTING TIPS: As you know, very cold temperatures make all engines a little harder to start.

  • Page 8: Maintenance

    Never wash or clean the air filter with high compressed SECURING YOUR AUGER DURING TRANSPORT air or by wetting it; never place in an oil bath or With your purchase of a StrikeMaster power auger, you cleaning solution. have acquired one of the world’s best precision cutting machines.

  • Page 10: Solo® Engines Limited Warranty

    If in doubt, ask your equipment vendor. They are responsible for warranty matters. Solo Inc. provides the initial purchaser with a 2 year engine warranty. We hope you will understand that we cannot be liable for damage resulting from the following causes: •...
  • Page 11 Your emission control system includes parts such as the carburetor, the ignition system and the exhaust system. Where a warrantable condition exists Solo will repair your small non-road power equipment engine at no cost to you including diagnosis, parts, and labor.
  • Page 12 LIMITED WARRANTY The warrantor’s obligation shall be limited to repairing or replacing any part, which upon examination by StrikeMaster, is determined to be defective.  This obligation begins on the date of purchase (as evidenced by a product receipt) and continues for a period of ONE YEAR after purchase (“warranty period”), with the exception of engines and parts subject to wear and tear.

This manual is also suitable for:

Solo pro laxerSolo lazer magSolo chipper mag

Table of Contents

Save PDF