Nilfisk-Advance SW700B Operator's Manual
  1. Manuals
  2. Brands
  3. Nilfisk-Advance Manuals
  4. Floor Machine
  5. SW700B
  6. Operator's manual
Nilfisk-Advance SW700B Operator's Manual

Nilfisk-Advance SW700B Operator's Manual

Hide thumbs Also See for SW700B:
Table of Contents

Advertisement

Quick Links

Electronic Service
Manuals
This electronic document is provided as a service to our custom-
ers. We do not create the contents of the information contained in
this document. Should you have detailed questions pertaining to
the information contained in this document, you may contact Michco,
or the manufacturer which provided the original information in this
electronic deliverable. Michco's only part in this electronic deliver-
able was the electronic assembly process.
You may contact Michco through the following methods:
Phone (517) 484-9312 or (800) 331-3339 MI, OH, IN only
2011 N. High St. -- Lansing, Michigan -- 48906
Fax: (517) 484-9836
Email: CustServ@Michco.com
Web site: www.Michco.Com
Parts Web site: www.FloorMachineParts.Com
Order Parts on Line at:
www.FloorMachineParts.Com
Directly to Parts & Service:
By Email:
Shop@Michco.com
By Fax: (517) 702-2041
By Voice: Use numbers above.
Serving the Cleaning Industry Since 1922
Notice: All copyrighted material remains property of original owners, all trademarks are property of respective
owners. Manuals are subject to Manufacturer's reproduction limitations. Originals or reproductions were provided
by manufacturers through a request. We make no warranty as to the correctness of information provided in this
document and you assume all risk.

Advertisement

Table of Contents
loading

Related Manuals for Nilfisk-Advance SW700B

Summary of Contents for Nilfisk-Advance SW700B

  • Page 1 Electronic Service Manuals This electronic document is provided as a service to our custom- ers. We do not create the contents of the information contained in this document. Should you have detailed questions pertaining to the information contained in this document, you may contact Michco, or the manufacturer which provided the original information in this electronic deliverable.
  • Page 2 SW700B/SW850B/G OPERATOR MANUAL Advance MODEL 908 2115 010 Advance MODELS 908 2213 010, 908 3401 010 FORM No. 56041472(2)00-02...

  • Page 3: Table Of Contents

    TABLE OF CONTENTS 56041472(2)00-02 pag. INTRODUCTION/GENERAL INFORMATION..........1 UNPACKING....................2 TECHNICAL DATA ..................3 CONTROL PANEL DESCRIPTION ..............4 PREPARING A NEW MACHINE (battery version)........5-7 PREPARING A NEW MACHINE (gasoline version)........8 START-UP (gasoline version)...............9-10 START-UP (battery version) ................11 USE OF THE MACHINE .................12-13 CENTRAL BRUSH ADJUSTMENT AND REPLACEMENT .......14-15 SIDE BRUSH ADJUSTMENT AND REPLACEMENT ........16 FILTER CLEANING AND REPLACEMENT ............17-18 MAINTENANCE (battery version) ...............19-20...

  • Page 4: Introduction/General Information

    Voltage: LISTED Conforms to UL STD. 583 9901122 MADE IN ITALY Nilfisk-Advance, Inc. Plymouth, MN, USA www.nilfisk-advance.com GENERAL SAFETY RULES Carefully follow the rules described below to avoid injury to the operator and damage to the machine. Carefully read the labels on the machine, do not cover them for any reason and replace them immediately if they become worn or damaged.

  • Page 5: Unpacking

    UNPACKING 56041472(2)00-02 When the machine is delivered, carefully inspect the shipping carton and the machine for damage. If damage is evident, save the shipping carton so that it can be inspected. Contact the Advance Customer Service Department immediately to file a freight damage claim.

  • Page 6: Technical Data

    TECHNICAL DATA 56041472(2)00-02 VERSION SW 700 B SW 850 B SW 850 G Voltage Main electric motor 600W-3000RPM 600W-3000RPM Gasoline engine model Vanguard OHV Nominal power at 3600 RPM 4HP-2,97 kw Displacement 126 cc / 7,69 cn.in Start Manual Max forward speed max 4,5 km/h (2,8mi/h) max 4,5 km/h (2,8mi/h) max 4,5 km/h (2,8mi/h) Main brush size diameter 265 mm...

  • Page 7: Control Panel Description

    CONTROL PANEL DESCRIPTION 56041472(2)00-02 BATTERY VERSION GASOLINE VERSION N° GASOLINE VERSION BATTERY VERSION DRIVE CONTROL LEVER DRIVE CONTROL LEVER FLAP LIFT-UP LEVER FLAP LIFT-UP LEVER DISPLAY VOLTMETER/HOUR METER BUTTON ON/OFF KEY ON/OFF KEY ENGINE ON/OFF SWITCH SUCTION STOP SUCTION STOP FILTER SHAKING LEVER FILTER SHAKING LEVER (STANDARD) FILTER SHAKING PUSH-BUTTON (OPTION)

  • Page 8: Preparing A New Machine (Battery Version)

    PREPARING A NEW MACHINE 56041472(2)00-02 It requires one 12-volt battery or alternatively, it is also possible to use two 6-volt batteries with a serial connection and with a higher capacity (for instance: 240 Ah @ 20). According to the country where it is sold, there are three possibilities: 1 - Battery is supplied with the machine and it is set, complete with acid solution and...
  • Page 9 PREPARING A NEW MACHINE 56041472(2)00-02 2 - If the battery is set without acid solution it must be filled up (density from 1,27 to 1,29 kg at 25°C) according to the instructions contained in next paragraph. BATTERIES FILLING UP WITH ACID SOLUTION Please pay a strict attention when working with sulphuric acid, as it corrosive.
  • Page 10 PREPARING A NEW MACHINE 56041472(2)00-02 3 - If the machine is supplied with no battery, they have to be procured and mounted. It is recommended to use the service of qualified personnel to choose and to install the new battery. The electric connection cables that are supplied together with the machine can be used for the battery connection.

  • Page 11: Preparing A New Machine (Gasoline Version)

    PREPARING A NEW MACHINE 56041472(2)00-02 (gasoline version) Engine version: Fill the fuel tank with unleaded gasoline. For oil control please check at page: 21...

  • Page 12: Start-Up (Gasoline Version)

    START-UP (gasoline version) 56041472(2)00-02 N.B.: Please read the Vanguard engine instructions manual. Turn the gasoline tap as per the figure in order to enable the flow to the carburettor. Move the starter lever as per the relevant figure. N.B.: Do not use the starter lever if the engine is hot and if the external temperature is high.

  • Page 13: Start-Up (Gasoline Version)

    START-UP (gasoline version) 56041472(2)00-02 If you wish to stop the engine, reduce the number of revolutions to a minimum (lever of previous figure), turn selector onto the “OFF” position and turn tap onto the “OFF/CLOSED” position.

  • Page 14: Start-Up (Battery Version)

    START-UP (battery version) 56041472(2)00-02 Insert the ignition key, turn it clockwise: the main motor will then be started-up while display “ A ” will show the battery voltage level. Check for the battery charge status by means of the specially-conceived display. The display has two functions: voltmeter and hour meter.

  • Page 15: Use Of The Machine

    USE OF THE MACHINE 56041472(2)00-02 Low the side brush. BATTERY VERSION When the motor is in operation, make sure that handle “ A ” has been lowered (suction enabled) ; if you pull the drive lever “ B ” you can adjust the running speed depending onto the quality and onto the quantity of the debris to be picked up.

  • Page 16: Use Of The Machine

    USE OF THE MACHINE 56041472(2)00-02 For efficient suction operation, the air filter must always be clean. Activate the filter shaker (you can also perform this operation when the machine is working) by pulling and releasing the handle as shown in the figure. Warning: always disable the suction function during this operation.

  • Page 17: Central Brush Adjustment And Replacement

    CENTRAL BRUSH ADJUSTMENT AND 56041472(2)00-02 REPLACEMENT Warning: these operations must be carried out with the machine off, the key switched off (for battery-operated version), and with the machine on even floor. When the main brush is fairly worn, its height must be adjusted to recover as much of the brush consumption as possible.
  • Page 18 CENTRAL BRUSH ADJUSTMENT AND 56041472(2)00-02 REPLACEMENT Remove the hub from the brush stem and place it onto the new brush; please do not change the direction of the bristles (please see following figu-re). Note: Before inserting the brush, replace the adjustment devices in the position that is farthest away from the ground.

  • Page 19: Side Brush Adjustment And Replacement

    SIDE BRUSH ADJUSTMENT AND 56041472(2)00-02 REPLACEMENT When the side brush is fairly worn, its height must be adjusted to recover as much of the brush consumption as possible. Lower the brush (motor on). Please make sure that the ground contact area is as shown in the figure.

  • Page 20: Filter Cleaning And Replacement

    FILTER CLEANING AND REPLACEMENT 56041472(2)00-02 The filter requires a periodical and complete cleaning operation. Remark: Depending onto the customer’s request, the machine is supplied with two options : 1- Manually-operated filter shaker (battery- fed). 2- Electrically-operated filter shaker (only battery-operated version). Lift the bonnet to remove the filter.

  • Page 21: Filter Cleaning And Replacement

    FILTER CLEANING AND REPLACEMENT 56041472(2)00-02 After cleaning, reinstall both the filter and the fixing cover. Turn the two cover side levers inwards. Reconnect the cable of the electric filter shaker motor (if installed).

  • Page 22: Maintenance (Battery Version)

    MAINTENANCE 56041472(2)00-02 The location of the adjustment device for Battery version, is as shown in the figure. To carry out the adjustment, loosen the lock nut "A" and turn the adjusting nut "B". Check the correct tightening, operating the traction control lever. BATTERY CONTROL AND RECHARGE Please perform a periodical control of the electrolyte level inside the battery.
  • Page 23 MAINTENANCE 56041472(2)00-02 - connect the battery connector to the battery charger. - connect the battery charger to the mains (the mains voltage level and the frequency have to match the corresponding levels that are applicable for the battery charger). At the end of the recharge disconnect the battery from the battery charger and reconnect it to the machine.

  • Page 24: Maintenance (Gasoline Version)

    MAINTENANCE (gasoline version) 56041472(2)00-02 We remaind you that it is necessary to carefully read the Vanguard engine use and maintenance manual and we offer you some other practical advice: Check the engine oil level twice a week by means of the specially-conceived gauge; to top up use the oil indicated in the engine Use and Maintenance manual Remark: Replace engine oil the first time after...
  • Page 25 MAINTENANCE (gasoline version) 56041472(2)00-02 Check regularly the engine air filter condition. If necessary, wash the filter with water and soap or with another home-use detergent. Squeeze and dry it properly. Soak it with engine oil and squeeze it in order to get rid of extra oil.

  • Page 26: Summary Table (Battery-Operated Version Maintenance)

    SUMMARY TABLE 56041472(2)00-02 Warning: these operations must be carried out with the machine off and the key switched off. All periodic or extraordinary maintenance operations must be performed by skilled personnel, or by an authorised service centre. UPON EVERY EVERY EVERY EVERY CONTROL...

  • Page 27: Summary Table (Gasoline-Operated Version Maintenance)

    SUMMARY TABLE 56041472(2)00-02 (gasoline-operated version maintenance) Warning: these operations must be carried out with the machine off. All periodic or extraordinary maintenance operations must be performed by skilled personnel, or by an authorised service centre. For any maintenance work on the engine, refer to its instruction manual.

  • Page 28: Optional Accessories

    OPTIONAL ACCESSORIES 56041472(2)00-02 High capacity batteries for electrical version High capacity batteries for electrical version 6V-244 Ah @ 20 Battery charger. Different kinds of brushes (central and side) for various applications. Polyester-made washable filter. For all optional accessories, please call your dealer.

  • Page 29: Safety Functions/Troubleshooting

    SAFETY FUNCTIONS 56041472(2)00-02 The battery-operated version is equipped with a display. The display has two functions: voltmeter and hour meter. The voltmeter includes a stop function for under-voltage that disables automatically all functions, including the drive, when the battery reaches a voltage level of 10,5 volts (flashing display).
  • Page 30 Nilfisk-Advance, Inc. 14600 21st Avenue North Plymouth, MN, 55447-3408 www.nilfisk-advance.com Phone: 800-989-2235 Fax: 800-989-6566 ©1999 Nilfisk-Advance, Inc. Plymouth, MN, 55447-3408 Printed in the U.S.A.

This manual is also suitable for:

Sw850b/gSw850bSw850g

Table of Contents