CONTROLLO VISIVO E REGOLAZIONE DELLE CINGHIE DI TRASMISSIONE E DELLA FRIZIONE ............................31 CONTROLLO DELL’ASSORBIMENTO ELETTRICO DEL MOTORE PRINCIPALE ........... 32 CONTROLLO E SOSTITUZIONE DEI CARBONCINI DEL MOTORE PRINCIPALE .......... 33 SMONTAGGIO/MONTAGGIO DEL MOTORE PRINCIPALE ................34 RICERCA GUASTI .............................. 36 SW 750 1463162000(2)2009-02...
Page 4
SMONTAGGIO/MONTAGGIO DELLE BATTERIE ....................41 CONTROLLO DELLA FUNZIONALITÀ DELL’INTERRUTTORE DI SICUREZZA APERTURA COFANO ..42 CONTROLLO/SOSTITUZIONE DEL FUSIBILE LAMELLARE ................42 RICERCA GUASTI .............................. 43 DISPOSIZIONE COMPONENTI ......................... 43 SCHEMA ELETTRICO ............................44 PIEDINATURA CONNETTORE CARICABATTERIE (CH1) ................. 45 SW 750 1463162000(2)2009-02...
La macchina sia saldamente legata al mezzo di trasporto ALTRI MANUALI DISPONIBILI Presso Nilfisk Literature Service Department sono disponibili i seguenti manuali: – SW 750, Catalogo Ricambi - Codice Nilfisk 146 3085 000 – SW 750, Manuale operatore - Codice Nilfisk 146 3080 000 –...
Non lavorare sotto la macchina sollevata senza adeguati sostegni fissi di sicurezza. – Non operare con questa macchina in ambienti dove sono presenti polveri, liquidi o vapori nocivi, pericolosi, infiammabili e/o esplosivi: questa macchina non è adatta a raccogliere polvere pericolosa. SW 750 1463162000(2)2009-02...
Page 7
La macchina non deve essere abbandonata, al termine del suo ciclo di vita, per la presenza al suo interno di materiali tossico-nocivi (batterie, plastica, ecc.), soggetti a norme che prevedono lo smaltimento presso centri appositi (vedere il capitolo Rottamazione nel Manuale operatore). SW 750 1463162000(2)2009-02...
Motore spazzola laterale 40 W Motore impianto di aspirazione 50 W Aspirazione e filtraggio polveri Valori Filtro polveri da 5-10 µm (poliestere) Superficie filtro polveri (10.8 ft2) Depressione vano spazzola centrale 12 mm H O (0.47 in H SW 750 1463162000(2)2009-02...
Controllo visivo delle cinghie di trasmissione e della ruota di frizione Regolazione del tenditore della cinghia di trazione Controllo del serraggio dei dadi e delle viti Controllo o sostituzione dei carboncini dei motori (1): e dopo le prime 8 ore. SW 750 1463162000(2)2009-02...
Eseguire di nuovo il punto 1 per controllare la corretta regolazione dell’altezza da terra della spazzola laterale. Quando l’eccessivo consumo della spazzola non ne permette più la regolazione, sostituire la spazzola come previsto al paragrafo specifico. S301585 SW 750 1463162000(2)2009-02...
All’interno della spazzola laterale, svitare il pomello (A) quindi rimuovere la spazzola (B) sganciandola dai tre perni (C). Montaggio Montare sulla macchina la nuova spazzola agganciandola ai perni (C), quindi avvitare la manopola (A). Regolare l’altezza della nuova spazzola operando come riportato al paragrafo precedente. S301586 SW 750 1463162000(2)2009-02...
Porre particolare attenzione nell’eseguire l’operazione di controllo sopraindicata e non fare mai funzionare la macchina al di fuori delle condizioni indicate. 1.2 in - 2 in 3 cm - 5 cm S301587 SW 750 1463162000(2)2009-02...
Installare la nuova spazzola centrale, orientando le setole (D) come indicato in figura. Montare la nuova spazzola eseguendo i punti da 3 a 6 in ordine inverso. Regolare l’altezza della spazzola centrale operando come indicato al paragrafo specifico. S301588 SW 750 1463162000(2)2009-02...
Eseguire i punti da 2 a 4 in ordine inverso. Controllare visivamente e regolare le cinghie di trasmissione e della ruota di frizione (vedere procedura al paragrafo specifico). Installare il cofano (vedere procedura al paragrafo specifico). S301589 SW 750 1463162000(2)2009-02...
Eseguire i punti da 3 a 5 in ordine inverso. Controllare visivamente e regolare le cinghie di trasmissione e della ruota di frizione (vedere procedura al paragrafo specifico). Installare la spazzola centrale (vedere procedura al paragrafo specifico). Installare il cofano (vedere procedura al paragrafo specifico). S301590 SW 750 1463162000(2)2009-02...
Nel caso in cui le operazioni sopradescritte non portino ad un corretto assorbimento elettrico, è necessario sostituire il motore (vedere procedura al paragrafo specifico). Installare la copertura della spazzola laterale (vedere procedura al paragrafo specifico). S301591 SW 750 1463162000(2)2009-02...
Rimuovere il mozzo (B) della spazzola laterale. Scollegare il connettore (C) del motore (E) della spazzola laterale. Rimuovere le viti (D). Rimuovere il motore (E) della spazzola laterale. Montaggio Montare i componenti nell’ordine inverso rispetto allo smontaggio. S301592 SW 750 1463162000(2)2009-02...
La tensione della batteria è troppo bassa, il segnalatore luminoso (4) è acceso (caricare la batteria). I carboncini del motore sono consumati (sostituirli). Il motore è in avaria (ripararlo o sostituirlo). Il cablaggio è danneggiato (ripararlo). Il fusibile ripristinabile è interrotto (ripristinarlo). L’interruttore generale è danneggiato (sostituirlo). SW 750 1463162000(2)2009-02...
Considerare che il flap anteriore ha dei tagli verticali tipici (E). Se necessario sostituire i flap anteriore e/o posteriore (vedere procedura al paragrafo specifico). 0-2 mm 0-0.08 in S301593 SW 750 1463162000(2)2009-02...
Al banco, rimuovere le viti (D), quindi rimuovere il gruppo flap con bandelle (E). Rimuovere la vite con dado (F) e separare il flap sinistro (G) dalle bandelle (H). Montaggio Montare i componenti nell’ordine inverso rispetto allo smontaggio. S301594 SW 750 1463162000(2)2009-02...
Rimuovere le viti (A), quindi rimuovere il gruppo flap destro con bandelle (B). Al banco, rimuovere la vite con dado (C) e separare il flap destro (D) dalle bandelle (E). Montaggio Montare i componenti nell’ordine inverso rispetto allo smontaggio. S301595 SW 750 1463162000(2)2009-02...
S301596 SMONTAGGIO/MONTAGGIO DEL FLAP ANTERIORE Smontaggio Rimuovere il contenitore rifiuti (9). Al banco, rimuovere le viti (A), quindi rimuovere la bandella (B). Rimuovere il flap anteriore (C). Montaggio Montare i componenti nell’ordine inverso rispetto allo smontaggio. S301597 SW 750 1463162000(2)2009-02...
Pulire la guarnizione (L) del contenitore rifiuti lungo tutta la superficie perimetrale e controllare inoltre che sia integra e idonea alla tenuta. In caso contrario, procedere alla sostituzione. Montare i componenti nell’ordine inverso rispetto allo smontaggio. NOTA Al montaggio, il filtro deve essere orientato con la guarnizione (J) rivolta come indicato in figura. S301598 SW 750 1463162000(2)2009-02...
Controllare che i terminali (A) dello scuotifiltro, siano integri e che siano a contatto del filtro polveri (B). Azionare la manopola scuotifiltro (C) e controllare che i terminali (A) scuotano correttamente il filtro polveri (B). Installare il contenitore rifiuti (9). S301599 SW 750 1463162000(2)2009-02...
Nel caso in cui le operazioni sopradescritte non portino ad un corretto assorbimento elettrico, è necessario sostituire il motore (vedere procedura al paragrafo specifico). Installare il cofano (vedere procedura al paragrafo specifico). S301600 SW 750 1463162000(2)2009-02...
Presenza di corpi estranei che bloccano la ventola di aspirazione (rimuovere il motore con la ventola di aspirazione). Il motore dell’impianto di aspirazione è in avaria (ripararlo/sostituirlo). LO SCUOTIFILTRO NON FUNZIONA Possibili cause: I terminali dello scuotifiltro sono danneggiati (sostituire lo scuotifiltro). SW 750 1463162000(2)2009-02...
Allentare il dado (E), quindi regolare il cavo di comando trazione con il registro (D). A regolazione raggiunta, serrare il dado (E). Controllare la funzionalità della molla di richiamo (F). Installare il cofano (vedere procedura al paragrafo specifico). S301602 SW 750 1463162000(2)2009-02...
Eseguire i punti da 4 a 8 in ordine inverso. Controllare visivamente e regolare le cinghie di trasmissione e della ruota di frizione (vedere procedura al paragrafo specifico). Eseguire i punti da 1 a 3 in ordine inverso. S301603 SW 750 1463162000(2)2009-02...
Il cavo di comando trazione è sregolato o rotto (regolarlo/sostituirlo). La cinghia di trazione è sregolata o rotta (regolarla/sostituirla). I carboncini del motore principale sono consumati (sostituirli). Il motore principale è in avaria (ripararlo/sostituirlo). La ruota di frizione è sregolata o usurata (regolarla/sostituirla). SW 750 1463162000(2)2009-02...
(R) con l’asola del supporto (U). Per l’allineamento utilizzare una punta da 5.5 mm. Con la ruota integra o non usurata è consigliato allineare con il 3° foro (R). A regolazione raggiunta serrare il dado (N). Eseguire i punti da 1 a 3 in ordine inverso. S301604 SW 750 1463162000(2)2009-02...
Nel caso in cui le operazioni sopradescritte non portino ad un corretto assorbimento elettrico, è necessario sostituire il motore (vedere procedura al paragrafo specifico). Installare il cofano (vedere procedura al paragrafo specifico). S301605 SW 750 1463162000(2)2009-02...
Se necessario, sostituire i carboncini. I carboncini devono essere sostituiti in blocco. Rassetto Montare i componenti nell’ordine inverso rispetto allo smontaggio. S301606 SW 750 1463162000(2)2009-02...
Eseguire i punti da 6 a 11 in ordine inverso. Controllare visivamente e regolare le cinghie di trasmissione e della ruota di frizione (vedere procedura al paragrafo specifico). Eseguire i punti da 1 a 5 in ordine inverso. S301607 SW 750 1463162000(2)2009-02...
Page 37
MANUALE DI ASSISTENZA ITALIANO MOTORE PRINCIPALE SMONTAGGIO/MONTAGGIO DEL MOTORE PRINCIPALE (Continua) S301608 SW 750 1463162000(2)2009-02...
LA MACCHINA NON SI MUOVE/LA SPAZZOLA CENTRALE NON RUOTA Possibili cause: Le cinghie di trasmissione sono sregolate o rotte (regolarle/sostituirle). Vedere anche la ricerca guasti relativa ai seguenti sistemi: – Sistema di spazzatura – Impianto di trazione SW 750 1463162000(2)2009-02...
• se ci sono anomalie visibili nei vari componenti; Collegare il connettore negativo della batteria (22), quindi installare il cofano (vedere procedura al paragrafo specifico). Installare la copertura della spazzola laterale (vedere procedura al paragrafo specifico). SW 750 1463162000(2)2009-02...
Sollevare il cofano (F) e appoggiarlo a terra. Se necessario, scollegare i connettori elettrici (G) (dopo avere segnato la loro posizione reciproca); quindi scollegare il connettore elettrico (H) e rimuovere il cofano (I). Montaggio Montare i componenti nell’ordine inverso rispetto allo smontaggio. S301609 SW 750 1463162000(2)2009-02...
6. Svitare il dado autobloccante (B). 7. Svitare la manopola (C) dalla piastra (D). 8. Rimuovere le viti (E) e rimuovere la copertura spazzola laterale (F). Montaggio 9. Montare i componenti nell’ordine inverso rispetto allo smontaggio. S301610 SW 750 1463162000(2)2009-02...
Quando si accende il segnalatore luminoso verde (F), la batteria è carica. Scollegare il cavo del caricabatterie (B) dalla rete elettrica e inserirlo nel proprio alloggiamento (C). NOTA Quando il caricabatterie è collegato alla rete elettrica, tutte le funzioni della macchina vengono automaticamente escluse. S301611 SW 750 1463162000(2)2009-02...
(E) ed (F). Se necessario, quando viene installata una batteria di maggiori dimensioni, utilizzare i fori (K) e (L) per bloccare la batteria mediante le squadrette (G) e (H) con le viti (E) ed (F). S301612 SW 750 1463162000(2)2009-02...
S301613 CONTROLLO/SOSTITUZIONE DEL FUSIBILE LAMELLARE Rimuovere il cofano (30) (vedere procedura al paragrafo specifico). Controllare/sostituire il fusibile lamellare da 7.5 A (A) del motore dell’impianto di aspirazione. Installare il cofano (30) (vedere procedura al paragrafo specifico). S301614 1463162000(2)2009-02 SW 750...
Il cablaggio è tagliato o schiacciato (ripararlo). DISPOSIZIONE COMPONENTI Legenda: Batterie Caricabatterie - controllo funzioni Scheda led Relè Fusibile principale Fusibile ventola di aspirazione Fusibile spazzola laterale Motore principale Motore impianto di aspirazione Motore spazzola laterale Interruttore generale Microinterruttore contenitore rifiuti S301615 SW 750 1463162000(2)2009-02...
Rosso Motore impianto di aspirazione Viola Motore spazzola laterale Bianco Interruttore generale Giallo Microinterruttore contenitore rifiuti Il caricabatterie svolge anche la funzione di controllo del livello di carica della batteria e di controllo dell’accensione della macchina. S301616 SW 750 1463162000(2)2009-02...
Con SW1 su pos. I o II e batt. quasi Scarica o caricabatterie in fase Anodo LED giallo (LDY) (12V) di carica Con SW1 su pos. I o II e batt. carica o caricabatterie in fase di carica Anodo LED verde (LDG) (12V) terminata SW 750 1463162000(2)2009-02...
Page 49
MAIN MOTOR ................................31 DRIVING BELT AND CLUTCH VISUAL INSPECTION AND ADJUSTMENT ............31 MAIN MOTOR ELECTRICAL INPUT CHECK ..................... 32 MAIN MOTOR CARBON BRUSH CHECK AND REPLACEMENT ..............33 MAIN MOTOR DISASSEMBLY/ASSEMBLY ....................... 34 TROUBLESHOOTING ............................36 SW 750 1463162000(2)2009-02...
The machine is securely fastened to the means of transport. OTHER AVAILABLE MANUALS The following manuals are available at Nilfisk Literature Service Department: – SW 750, Spare Parts List – Nilfisk Form Number 146 3085 000 – SW 750, User Manual – Nilfisk Form Number 146 3080 000 –...
Do not work under the lifted machine without supporting it with safety stands. – Do not operate the machine near toxic, dangerous, flammable and/or explosive powders, liquids or vapours: This machine is not suitable for picking up hazardous dust. SW 750 1463162000(2)2009-02...
Page 53
If parts must be replaced, require ORIGINAL spare parts from a Dealer or Authorised Retailer. – The machine must be disposed of properly, because of the presence of toxic-harmful materials (batteries, plastics, etc.), which are subject to standards that require disposal in special centers (see Scrapping chapter in the User Manual). SW 750 1463162000(2)2009-02...
Side broom motor 40 W Vacuum system motor 50 W Dust vacuuming and filtering Values Dust filter 5-10 µm (polyester) Dust filter surface 10.8 ft2 (1 m Main broom compartment vacuum 0.47 in H O (12 mm H SW 750 1463162000(2)2009-02...
Hopper gasket check Filter shaker operation check Drive belt and wheel clutch visual inspection Drive system belt tensioner adjustment Nut and screw tightening check Motor carbon brush check or replacement (1): And after the first 8 hours. SW 750 1463162000(2)2009-02...
Battery charger - Function control Vacuum system motor lamellar fuse (7.5 A) Hood Hopper upper handle Hopper lower handles Serial number plate/technical data/conformity certification Side skirts Front skirt Rear skirt Side broom cover Drive system control cable adjuster SW 750 1463162000(2)2009-02...
Page 58
ENGLISH SERVICE MANUAL GENERAL INFORMATION 20 19 S301584 SW 750 1463162000(2)2009-02...
Perform step 1 again to check that the side broom is at the correct distance from the ground. When the broom is too worn and can no longer be adjusted, replace it according to the procedure shown in the relevant paragraph. S301585 SW 750 1463162000(2)2009-02...
Loosen the knob (A) inside the side broom, then remove the broom (B) by disengaging it from the pins (C). Assembly Install the new broom on the machine engaging it on the pins (C), then tighten the knob (A). Adjust the height of the new broom according to the procedure shown in the previous paragraph. S301586 SW 750 1463162000(2)2009-02...
Pay careful attention when performing the above-mentioned checks, and always use the machine according to the indicated conditions. 1.2 in - 2 in 3 cm - 5 cm S301587 SW 750 1463162000(2)2009-02...
Install the new main broom with the bristles rows (D) bent as shown in the figure. Install the new broom by performing steps 3 to 6 in the reverse order. Adjust the main broom height according to the procedure shown on the relevant page. S301588 1463162000(2)2009-02 SW 750...
Perform steps 2 to 4 in the reverse order. Visually inspect and adjust the driving belts and wheel clutch (see the procedure in the relevant paragraph). Install the hood (see the procedure in the relevant paragraph). S301589 SW 750 1463162000(2)2009-02...
Visually inspect and adjust the driving belts and wheel clutch (see the procedure in the relevant paragraph). Install the main broom (see the procedure in the relevant paragraph). Install the hood (see the procedure in the relevant paragraph). S301590 SW 750 1463162000(2)2009-02...
If necessary, disassemble the motor (see the procedure in the relevant paragraph), clean it and check its moving parts. If the above-mentioned procedures do not lead to a correct electrical input,the motor must be replaced (see the procedure in the relevant paragraph). Install the side broom cover (see the procedure in the relevant paragraph). S301591 SW 750 1463162000(2)2009-02...
Remove the side broom hub (B). Disconnect the connector (C) of the side broom motor (E). Remove the screws (D). Remove the side broom motor (E). Assembly Assemble the components in the reverse order of disassembly. S301592 SW 750 1463162000(2)2009-02...
The battery voltage is too low, the warning light (4) is on (charge the battery). The motor carbon brushes are worn (replace). The motor is faulty (repair/replace). The wiring harness is damaged (repair). There is an open in the circuit breaker (reset). The main switch is damaged (replace). SW 750 1463162000(2)2009-02...
Check that the front and rear skirts (C and D) slightly rub on the ground. Check the skirts for integrity, cuts or tears, which can reduce the machine vacuum capabilities. Note that the front skirt has typical vertical cuts (E). If necessary replace the front and/or rear skirts (see the procedure in the relevant paragraph). 0-2 mm 0-0.08 in S301593 SW 750 1463162000(2)2009-02...
At the workbench, remove the screws (D), then remove the skirt assembly with straps (E). Remove the screw (F) and separate the left skirt (G) from the straps (H). Assembly Assemble the components in the reverse order of disassembly. S301594 SW 750 1463162000(2)2009-02...
Remove the screws (A), then remove the right skirt assembly with straps (B). At the workbench, remove the screw (C) and separate the right skirt (D) from the straps (E). Assembly Assemble the components in the reverse order of disassembly. S301595 SW 750 1463162000(2)2009-02...
S301596 FRONT SKIRT DISASSEMBLY/ASSEMBLY Disassembly Remove the hopper (9). At the workbench, remove the screws (A), then remove the strap (B). Remove the front skirt (C). Assembly Assemble the components in the reverse order of disassembly. S301597 SW 750 1463162000(2)2009-02...
Clean the bearing surface of the hopper gasket (L) and check it for integrity and sealing capabilities. If necessary, replace Assemble the components in the reverse order of disassembly. NOTE Assemble the filter with the gasket (J) positioned as shown in the figure. S301598 SW 750 1463162000(2)2009-02...
Check the filter shaker terminals (A) for integrity and contact with the dust filter (B). Activate the filter shaker knob (C) and check that the terminals (A) shake the dust filter (B) correctly. Install the hopper (9). S301599 SW 750 1463162000(2)2009-02...
If the above-mentioned procedures do not lead to a correct electrical input,the motor must be replaced (see the procedure in the relevant paragraph). Install the hood (see the procedure in the relevant paragraph). S301600 SW 750 1463162000(2)2009-02...
There are foreign materials clogging the vacuum fan (remove the motor and the vacuum fan). The vacuum system motor is faulty (repair/replace). THE FILTER SHAKER DOES NOT WORK Possible causes: The filter shaker terminals are damaged (replace the filter shaker). SW 750 1463162000(2)2009-02...
Loosen the nut (E), then adjust the drive system control cable with the adjuster (D). When the adjustment is completed, tighten the nut (EN). Check the return spring (F) for proper operation. Install the hood (see the procedure in the relevant paragraph). S301602 SW 750 1463162000(2)2009-02...
Assembly Perform steps 4 to 8 in the reverse order. Visually inspect and adjust the driving belts and wheel clutch (see the procedure in the relevant paragraph). Perform steps 1 to 3 in the reverse order. S301603 SW 750 1463162000(2)2009-02...
The drive system control cable is misadjusted or broken (adjust/replace). The driving belt is misadjusted or broken (adjust/replace). The main motor carbon brushes are worn (replace). The main motor is faulty (repair/replace). The wheel clutch is misadjusted or broken (adjust/replace). 1463162000(2)2009-02 SW 750...
With an integral wheel clutch (O) or not worned it is suggested the alignment with the 3rd hole (R). When the adjustment is completed, tighten the nut (N). Perform steps 1 to 3 in the reverse order. S301604 SW 750 1463162000(2)2009-02...
If necessary, disassemble the motor (see the procedure in the relevant paragraph), clean it and check its moving parts. If the above-mentioned procedures do not lead to a correct electrical input,the motor must be replaced (see the procedure in the relevant paragraph). Install the hood (see the procedure in the relevant paragraph). S301605 SW 750 1463162000(2)2009-02...
If necessary, replace the carbon brushes. Replace the carbon brushes as an assembly. Reset Assemble the components in the reverse order of disassembly. S301606 SW 750 1463162000(2)2009-02...
Assembly Perform steps 6 to 11 in the reverse order. Visually inspect and adjust the driving belts and wheel clutch (see the procedure in the relevant paragraph). Perform steps 1 to 5 in the reverse order. S301607 SW 750 1463162000(2)2009-02...
Page 83
SERVICE MANUAL ENGLISH MAIN MOTOR MAIN MOTOR DISASSEMBLY/ASSEMBLY (Continues) S301608 SW 750 1463162000(2)2009-02...
Wait at least 2 minutes after the open circuit. After repairing, press the circuit breaker button (21). THE MACHINE DOES NOT MOVE/THE MAIN BROOM DOES NOT TURN Possible causes: The driving belts are misadjusted or broken (adjust/replace). See also the Troubleshooting of the following systems: – Sweeping system – Drive system SW 750 1463162000(2)2009-02...
• Visible faults in the components; Connect the negative connector of the battery (22), then install the hood (see the procedure in the relevant paragraph). Install the side broom cover (see the procedure in the relevant paragraph). SW 750 1463162000(2)2009-02...
Lift the hood (F) and lay it on the ground. If necessary, disconnect the connectors (G) (mark their positions to reinstall them correctly); then disconnect the connector (H) and remove the hood (I). Assembly Assemble the components in the reverse order of disassembly. S301609 SW 750 1463162000(2)2009-02...
Remove the lever (A). Remove the self-locking nut (B). Unscrew the knob (C) from the plate (D). Remove the screws (E), then remove the side broom cover (F). Assembly Assemble the components in the reverse order of disassembly. S301610 SW 750 1463162000(2)2009-02...
When the green warning light (F) turns on, the batteries are charged. Disconnect the battery charger cable (B) from the electrical mains and place it in the housing (C). NOTE When the battery charger is connected to the electrical mains, all machine functions are automatically disabled. S301611 SW 750 1463162000(2)2009-02...
Place the battery against the edges (I) and (J), then bring the brackets (G) and (H) against the battery (C) and tighten the screws (F). If necessary, when installing a bigger battery, use the holes (K) and (L) to hold the battery with the brackets (H), with the screws (F). S301612 SW 750 1463162000(2)2009-02...
S301613 LAMELLAR FUSE CHECK/REPLACEMENT Remove the hood (30) (see the procedure in the relevant paragraph). Check/replace the 7.5 A vacuum system motor lamellar fuse (A). Install the hood (30) (see the procedure in the relevant paragraph). S301614 SW 750 1463162000(2)2009-02...
The wiring harness is cut or squashed (repair). COMPONENT LAYOUT Key: Batteries Battery charger - Function control Electronic board LED Relay Main fuse Vacuum fan fuse Side broom fuse Main motor Vacuum system motor Side broom motor Main switch Hopper microswitch S301615 SW 750 1463162000(2)2009-02...
Side broom fuse Pink Main motor Vacuum system motor Violet Side broom motor White Main switch Yellow Hopper microswitch The battery charger cable has also the function of checking the battery charge and the machine ignition. S301616 SW 750 1463162000(2)2009-02...
SW1 on I or II and nearly discharged battery or plugged charger in III Yellow LED anode (LDY) (12V) charge phase SW1 on I or II and charged battery or plugged charger with charge Green LED anode (LDG) (12V) completed SW 750 1463162000(2)2009-02...
Need help?
Do you have a question about the SW 750 and is the answer not in the manual?
Questions and answers