Table of Contents
Advertisement
ELECTRICAL CONNECTION
WARNING
E E l l e e c c t t r r i i c c a a l l R R e e q q u u i i r r e e m m e e n n t t s s
A 115 volt, 60 Hz, AC only 15 amp fused electrical supply is required. (A time delay
fuse or circuit breaker is recommended.) It is recommended that a separate circuit,
serving only this appliance, be provided.
• • E E L L E E C C T T R R I I C C A A L L G G R R O O U U N N D D I I S S R R E E Q Q U U I I R R E E D D O O N N T T H H I I S S A A P P P P L L I I A A N N C C E E . .
• • D D O O N N O O T T U U N N D D E E R R A A N N Y Y C C I I R R C C U U M M S S T T A A N N C C E E S S R R E E M M O O V V E E T T H H E E P P O O W W E E R R S S U U P P P P L L Y Y C C O O R R D D
G G R R O O U U N N D D P P L L U U G G . .
• • D D O O N N O O T T U U S S E E A A N N E E X X T T E E N N S S I I O O N N C C O O R R D D
R R e e c c o o m m m m e e n n d d e e d d G G r r o o u u n n d d i i n n g g M M e e t t h h o o d d s s
For your personal safety, this unit must be grounded. This appliance is equipped with a 7' (2.1 m) power supply cord having a 3-
prong grounding plug. To minimize possible shock hazard, the cord must be plugged into a mating 3-prong grounding type wall
receptacle grounded in accordance with the National Electrical Code and local codes and ordinances. If the circuit does not have
a grounding type receptacle, it is the responsibility and obligation of the customer to exchange the existing receptacle in
accordance with the National Electrical Code and applicable local codes and ordinances. The third ground plug SHOULD NOT,
under any circumstances, be cut or removed. All UL listed refrigerated drawers are equipped with this type of plug.
FINAL PREPARATION
1. Some stainless steel parts may have a plastic protective wrap which must be peeled off. The interior of the unit should be
washed thoroughly with hot, soapy water, rinsed and wiped dry to remove film residue and any installation dust or debris
before being used. Solutions stronger than soap and water are rarely needed.
2. All stainless steel parts should be wiped with hot soapy water. If buildup occurs, do not use steel wool, abrasive cloths,
cleaners, or powders. If it is necessary to scrape stainless steel to remove encrusted materials, soak with hot, wet cloths to
loosen the material, then use a wood or nylon scraper. Do not use a metal knife, spatula, or any other metal tool to scrape
stainless steel; scratches are almost impossible to remove.
OPERATING INSTRUCTIONS
G G e e n n e e r r a a l l T T i i p p s s a a n n d d S S u u g g g g e e s s t t i i o o n n s s
•After making a temperature adjustment, allow at least 24 hours for your unit to reach a new temperature setting.
•The motor will start and stop often. It must do this to maintain the temperature setting.
•Unplug the unit before working on anything with the electrical system.
•Exercise caution when sweeping, vacuuming, or mopping near the front of the unit.
•Avoid leaning on the drawer fronts. You may bend the drawer slides or tip the unit.
ELECTRICAL SHOCK HAZARD
Failure to follow these instructions could result in fire or electrical
shock.
11
Power Supply
Grounding type wall
with 3-prong
receptacle
grounding plug
Advertisement
Table of Contents
